HP 1050c HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60
HP 1050c - DesignJet Plus Color Inkjet Printer Manual
View all HP 1050c manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 1050c manual content summary:
- HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 1
+3 'HVLJQ-HW 6HULHV 7DNH8S 5HHO User's Guide - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 2
fitness for a particular purpose. The Hewlett-Packard Company shall not be liable for incidental or consequential damages in connection with, or arising out of the furnishing. performance. or use of this document and the program material which it describes. HP DesignJet 1000 Series Take-Up Reel 2 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 3
Contents Upgrading your Printer 4 Checking the Firmware Revision Number 4 Installing a New Firmware Module 5 Take-Up Reel Components 11 Installing the Take-Up Reel 13 Loading Paper on to the Take-Up Reel 21 Unloading Paper from the Take-Up Reel 29 Changing the Core Tube on the Take-Up Reel 32 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 4
Upgrading your Printer Utilities Statistics Code rev Before installing your take-up reel, you should check that the firmware module installed in your printer supports a take-up reel. Checking the Firmware Revision Number You can find out your firmware revision number from the printer's front panel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 5
1 If the printer is turned on, turn it off at the front panel. 2 Looking at the rear of the printer, remove the paper path deflector from the left rear side of the printer. To do this, push the two slots in the deflector downwards and then pull it towards you. 2 1 5 HP DesignJet 1000 Series Take - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 6
the power cord and the interface cable. 2 1 Power Cord Power Off the Printer 4 Unscrew the four screws and remove the cover plate at the back of the printer. To prevent loss of these screws, loosely re-install them in the printer. 2 1 Cover Plate HP DesignJet 1000 Series Take-Up Reel 6 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 7
firmware module in the slot that is furthest to the right. 6 Put on a grounding wrist strap and attach the other end to the metal chassis of the printer Take the firmware module out of its bag. Hold the firmware module by its edges with the non-metallic edges toward you. 7 HP DesignJet 1000 Series - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 8
9 Carefully push the top edge of the firmware module into the slot. 10 Continue pushing the top edge of the firmware module until you feel it "click" into position. At the same time you will see that the top locking tab locks into position. HP DesignJet 1000 Series Take-Up Reel 8 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 9
the firmware module into the slot until you feel it "click" into position. Again, you will see that the bottom locking tab locks into position. 12 Remove the grounding wrist strap and then re-install the cover plate on the back of the printer, using the four screws. 2 1 9 HP DesignJet 1000 Series - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 10
-install the paper path deflector on the left side of the printer. 2 1 14 Reconnect the power cord and the interface cable and switch on the power isolator switch at the back of the printer. 1 Power Isolator Switch Power Cord You have now finished installing the firmware module. HP DesignJet 1000 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 11
-hand assembly Take-up reel spindle 3-inch core adaptors Paper guide Documentation, assembly tool, etc. +2++4''=/==3656510''4/0'9''/'m11/125m37m70m2mmmm +2++4''=/== 8'' / 203mm Paper weight (different lengths) 8'' / 203mm Deflector supports Deflector rod 11 HP DesignJet 1000 Series Take- - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 12
The following picture shows the main components of the take-up reel and where they are installed on the printer, Right-hand assembly Take-up reel sensor Left-hand assembly Deflector HP DesignJet 1000 Series Take-Up Reel 12 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 13
to Yes. If you do not find any "TUR installed" option, you may need to upgrade your printer's firmware (see Upgrading your Printer, on page 4). 2. If a roll of paper is loaded, remove it (see Chapter 3 of the User's Guide). 3. If the bin cover is in use, remove it. 4. Remove the bin assembly with - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 14
Remove the bin support from the legs assembly by removing four screws. Do not use these (shorter) screws for the next step. 10. Install the four (longer) screws from the take- up reel kit loosely into the legs as shown below. Do not tighten them yet. Install 4 screws HP DesignJet 1000 Series Take - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 15
10. screw as shown below. 13. Pull the left-hand assembly down so that it rests securely on the screws. 15. Tighten the two screws supporting the assembly. 16. Release the clamp on the right-hand assembly. by loosening the screw shown below. Do not remove the screw. 15 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 16
shown below. Clamp 18. Pull the right-hand assembly down so that it rests securely on the screws. Clamp screw 20. Tighten the two screws supporting the assembly. 21. Unscrew the screw on the sensor assembly shown below (but do not remove it) and open the clamp - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 17
. Tighten the screw to secure the clamp in place and connect the sensor cable as shown below. Ensure this is clipped under the foot 17 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 18
spindle lock is open. Power switch 27. Use the blue lever to unlock the left-hand paper guide on the take-up reel spindle. Remove the paper guide. 30. Install the take-up reel spindle into the printer 28. Assemble the take-up reel core and put it on to the spindle as shown below - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 19
-up reel assembly. 12'' / 305mm 32. A paper deflector, which consists of a rod and two supports, is supplied with the take-up reel kit. Fit the left and right supports on top of the printer's cross brace. 34. Rest the deflector rod on the two supports. 19 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 20
at the back of the printer, then turn on the printer using the on/off button on the front panel. 38. Wait until the printer has finished initializing and a "Ready" message is displayed on the front panel. You have now finished installing the take-up reel. HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 21
option to Yes. Now go to step 1 below. s If you do not already have a roll of paper in the printer, load the roll according to the instructions in Chapter 3 of the User's Guide. Soon after you have selected the paper type, the front panel will offer the option "Load Take-Up Reel (TUR)", which can be - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 22
2 Ensure that the spindle lock is closed. 3 Move the adjustment levers on the left and right paper guides to the unlocked position. HP DesignJet 1000 Series Take-Up Reel 22 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 23
the paper guides. Adjust the position of the core as shown below. The paper guides may be slightly stiff on the spindle: you may have to use both hands. 5 When you have adjusted the position of the core, pull the adjustment levers on both paper guides to the locked position. 23 HP DesignJet 1000 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 24
6 Pull the paper taut to the position shown below. Do not attempt to pull more paper out of the printer; if you need more paper, use the front panel. HP DesignJet 1000 Series Take-Up Reel 24 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 25
wound onto the core tube, ensure the paper is straight when it is attached. 8 Press the ↓ key on the front panel to advance the paper. Enough paper should be advanced so that the paper can wrap at least once around the core. Advance about this much paper 25 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 26
important that the paper weight is the same width as the paper you are using. By matching color coded lengths of plastic tube, you can make a paper weight for different widths of standard paper sizes: 24", 36". 12'' / 305mm +2+4+''=/=3=66515'0'0/4'9''/m'11/152m3m770m2mmmm HP DesignJet 1000 Series - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 27
3056650''47/'9''/m'1/1125m37m702mmmmm 12'' / 305mm 12 Press Enter on the printer's front panel, which will then display the Ready message. NOTE: When the take-up reel is in operation it is important to ensure that the takeup reel sensor is not blocked. 27 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 28
13 Shown below is how the printer should look when it is in operation. As paper is fed from the printer it drops down in a loop and up into the take-up reel spindle. Do not block the take-up reel sensor Make sure endcaps are clear of paper HP DesignJet 1000 Series Take-Up Reel 28 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 29
CUT key on the front panel. The front panel will prompt you to remove the paper weight and wind excess paper using the take-up reel buttons. 3 Important: Remove the paper weight as shown below. It may help you to remove the end-caps first. 12'' / 305mm 29 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 30
4 Press the paper wind button shown below to wind the paper hanging down onto the take-up reel. 5 Press Enter on the printer's front panel. The printer will now cut the paper. 6 Slide open the spindle lock on the right-hand side of the take-up reel. HP DesignJet 1000 Series Take-Up Reel 30 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 31
+ 12'' / 305mm 8 Unlock and remove the left-hand paper guide from the take-up reel spindle. Remove the core from the spindle. Take-up reel spindle Take-Up Core (with paper) Paper guide To remove roll paper from the printer, see the User's Guide. 31 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 32
on the take-up reel must be the same width as the paper you are using. To change the core, perform the following procedure. the printer as shown by pulling firmly on each end of the spindle, A then B. 42'' + + / =1=03=6655'07'/4'9m'/'1'1/m1523m770m2mmmm + 12'' / 305mm HP DesignJet 1000 Series - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 33
re-install the left hand guide assembly. NOTE: You can also use an empty cardboard tube to replace the plastic take-up core that was supplied with your printer. It is important that the take-up core is the same width as the paper you are using. By matching color coded lengths of plastic tube - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 34
to use a three-inch cardboard core, use the three-inch core adaptors shown below. Take-up reel spindle Right-hand paper guide 3-inch core adaptors XX'' / XXXmm XX'' + + + /==X=35X650'4X'/''9'/'X/1112m537m7m02mmmmm Left-hand paper guide Take-up core HP DesignJet 1000 Series Take-Up Reel 34 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 35
6 Install the take-up reel spindle into the printer by pushing firmly on each end of the spindle, A then B. 42'' + + / =1=03=6655'07'/4'9m'/'1'1/m1523m770m2mmmm + 12'' / 305mm 7 Slide shut the spindle lock on the right-hand side of the take-up reel. 35 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 36
Setup menu on the printer's front panel, then "Device setup" and "Drying time". This is explained in more detail in Chapter 2 of the User's Guide. Drying time=None This setting means there is no delay to the printing process. Hewlett-Packard has tested the HP paper range in different environmental - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 37
=Manual In this mode you can override the amount of time that the printer has estimated to print your image. However, the printer needs a certain minimum amount of time to print. If the amount of time that you have specified is less than this, the printer will ignore your setting. 37 HP DesignJet - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 38
Troubleshooting This page lists some possible explanations of problems that may occur with the take-up reel. Take-Up Reel Does Not Function s Perhaps you have a power problem. Check that the power cable is connected and that there is power available at the socket. s Check that the ON/OFF switch is - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 39
86° F) Operating Relative Humidity: 20% to 80% Noncondensing Storage ranges 95% humidity -40°C to 70°C (-40° F to 158° F) Printhead and Printhead Cleaners stored in the HP DesignJet Ink System Storage Container: Temperature: +15°C to +35°C (+59° F to +95° F) @ 20% - 80% Relative Humidity 39 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 40
SABS licensed. USA Federal Communications Commission. Class B digital device. CFR 47 Part 15 Australia New Zealand Meets AS/NZS 3548 Taiwan (ROC) BCIQ Certified Safety ' Laboratories UL 1950 Listed Poland PCBC certified Russia GOST certified HP DesignJet 1000 Series Take-Up Reel 40 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 41
Part 15.21 of the FCC Rules, any changes or modifications to this equipment not expressly approved by the Hewlett-Packard which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interferences by one or more 41 HP DesignJet 1000 Series Take-Up Reel - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 42
The user may find useful the following booklet prepared by the FCC: "How to Identify and Resolve Radio-TV Interference Problems". This booklet is available Canadian Department of Communications. Taiwanese EMI statement Address Hewlett-Packard Company Manager of Corporate Product Regulations 3000 - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 43
(1994) / EN 61000-3-3 (1995); FCC Part 15 - Class B / DOC-B / BCIQ Hewlett-Packard DesignJet series printer. Sant Cugat del Valles (Barcelona), 10th of May 1999 Josep-Maria Pujol, Site Quality Services Manager European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard - HP 1050c | HP DesignJet 1000 Series Take-Up Reel UserÂ’s Guide - C60 - Page 44
© Copyright Hewlett-Packard Company 1999 Part number: C6079-90001 First edition Printed in Europe Hewlett-Packard Company Barcelona Division Avda. Graells, 501 08190 Sant Cugat del Vallès Barcelona, Spain
7DNH±8S²5HHO
’HVLJQ-HW²³´´´²6HULHV
+3
User’s Guide