HP 1606 HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J
HP 1606 Manual
View all HP 1606 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 1606 manual content summary:
- HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 1
Gb SAN Switch Hardware Reference Guide Abstract This document provides information on installing, configuring, and maintaining the 8-Gb SAN family of HP StorageWorks Fibre Channel switches. This document is intended for system administrators and technicians with knowledge of SANs and HP StorageWorks - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 2
computer software. Valid license from HP required HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 3
of the 1606 Extension SAN Switch 25 Installing and activating Port Upgrade licenses 25 SAN Switch ISL Trunking groups 26 Supported SFP transceiver options 27 8-Gb SAN Switch software options 28 8-Gb SAN Switch hardware options 29 2 Installing and configuring an 8-Gb SAN Switch 31 Shipping - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 4
SAN Switches 55 Configuring the Encryption SAN Switch 55 Configuring the FCoE Converged Network Switch 56 Configuring the 1606 Extension SAN Switch 56 FCIP and Fibre Channel routing services configuration 56 Verifying switch operation 57 8-Gb SAN Switch LEDs ...58 8/8 and 8/24 SAN Switch LEDs - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 5
ranges ...89 FCoE Converged Network Switch data flow latency 93 Fibre Channel port specifications 93 POST and boot specifications ...93 POST ...93 Boot ...94 Supported HBAs and CNAs ...94 5 Support and other resources 95 HP technical support ...95 Subscription service ...95 Documentation feedback - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 6
Estonian notice ...104 Finnish notice ...104 French notice ...105 German notice ...105 Greek notice ...106 Hungarian notice ...106 Italian notice ...106 Latvian notice ...107 Lithuanian notice ...107 Polish notice ...107 Portuguese notice ...107 Slovakian notice ...108 Slovenian notice ...108 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 7
7 Port side of the FCoE Converged Network Switch 21 8 Nonport side of the FCoE Converged Network Switch 21 9 Port side of the HP 1606 Extension SAN Switch 24 10 Port numbering on the 1606 Extension SAN Switch 24 11 Nonport side of the 1606 Extension SAN Switch 25 12 Trunking groups example 27 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 8
the upper row of port slot 75 35 Nonport side LEDs 76 36 8/80 and Encryption SAN Switch fan assemblies on the nonport side 78 37 Inserting the fan assembly in the 8/80 SAN Switch 80 38 Installing a power supply in the 8/80 or Encryption SAN Switch 81 39 Class 1 laser product label 100 8 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 9
Converged Network Switch ...91 28 Laser data transmission ranges for the 1606 Extension SAN Switch Fibre Channel ports ...92 29 GbE data transmission ranges for the 1606 Extension SAN Switch 92 30 Data flow latency for the FCoE Converged Network Switch 93 8-Gb SAN Switch Hardware Reference Guide 9 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 10
31 Document conventions 97 10 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 11
Converged Network Switch provides low-latency lossless CEE ports, and 8-Gb FC ports in a single switch. The 1606 Extension SAN Switch is Tools, Advanced Zoning, and EGM as standard software components. • HP StorageWorks 8/24 SAN Switch-Ships with 16 ports activated and includes a Full Fabric license. - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 12
include Adaptive Networking or Extended Fabric. The HP StorageWorks 1606 Extension SAN Switch ships with the following additional license options: • Advanced Extension • Integrated Routing For more information on these features, see the Fabric OS Administrator's Guide for the firmware version you - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 13
Setup Wizard for easy setup and basic configuration. • Provides on-demand scaling of 8 to 24 ports. • Operates as a fully functional switch LEDs. Additionally, a pull-out tab identifies the serial number, MAC address, and WWN. Record the switch IP address on the pull-out tab for easy access. Figure - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 14
isolation. • Integrates a USB port that provides storage for firmware updates, output of the supportsave command and storage for configuration uploads and downloads. Port side of the 8/40 SAN Switch The port side of the 8/40 SAN Switch includes the system status LED, console port, Ethernet port and - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 15
8/40 SAN Switch ports By default, the 8/40 SAN Switch model integrates 24 licensed ports (ports 0 through 23). To enable additional ports, you must purchase and install the HP Storage Works 8/40 SAN Switch 8-Gb 8-port Upgrade LTU (part number T5519A): 8-Gb SAN Switch Hardware Reference Guide 15 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 16
isolation. • Integrates a USB port that provides storage for firmware updates, output of the supportsave command, and storage for configuration uploads and downloads. Port side of the 8/80 SAN Switch The port side of the 8/80 SAN Switch includes the system status LED, console port, Ethernet port - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 17
. Nonport side of the 8/80 SAN Switch and the Encryption SAN Switch Figure 5 shows the nonport side of the 8/80 SAN Switch and the Encryption SAN Switch, which contains the power supplies (including the AC power receptacle and AC power switch) and fans. 8-Gb SAN Switch Hardware Reference Guide 17 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 18
traffic) • Integrated with HP SKM system • Full 1:1 subscription on all 32 ports at 8 Gb/s • HA cluster, DEK cluster, and EG to enable transparent failover, host MPIO failover, and centralized management of multiple encryption switches • Support for automatic expiry or CLI manual based re-keying 18 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 19
Service (optional) to enable encryption capabilities across multiple fabrics • NPIV support • Two hot-swappable, redundant power supply FRUs • Three hot-swappable fan FRUs in the N+1 configuration facilitates firmware upgrades, serviceability, and system-log functionality • A switch subsystem and - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 20
45 Ethernet management port and EZSwitch Setup, which supports switch IP address discovery and configuration • Integrates a USB port that provides storage for firmware updates, as well as supportsave command output and configuration uploads and downloads • Provides two hot-swappable, redundant power - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 21
A fully licensed 1606 Extension SAN Switch has the following features: • FCIP capability • Includes up to eight FCIP tunnels. • Each FCIP tunnel is represented and managed as a VE_Port. • Fibre Channel Routing Services can be used over the FCIP link. 8-Gb SAN Switch Hardware Reference Guide 21 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 22
interface • One RJ-45 terminal port • One USB port for storing firmware updates, supportSave command output, and configuration uploads and downloads • Two redundant, hot-swappable combined power supply/fan assembly FRUs • Five internal temperature sensors 22 HP StorageWorks 8-Gb SAN Switches - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 23
is available to virtualize two or more IP address pairs (circuits) as part of a single FCIP tunnel. You can configure up to four circuits for a single FCIP tunnel. For more information on configuring circuits, see the Fabric OS Administrator's Guide. • Multiple FCIP tunnels can share the same GbE - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 24
Networking • Server Application Optimization • ISL Trunking • Fabric Watch • Advanced Performance Monitor • FICON CUP • FICON Accelerator For information on these features, see the Fabric OS Administrator's Guide. Port side of the 1606 Extension SAN Switch of the HP 1606 Extension SAN Switch . The - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 25
1606 Extension SAN Switch switch. Alternately, you can use the switchshow command to display the WWN. 3. Contact your HP representative to purchase the appropriate Port Upgrade license. HP requires the switch WWN obtained in Step 2 to assign a license key. 8-Gb SAN Switch Hardware Reference Guide - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 26
5. Configure the laser. For example: portstart 16-31 6. Enter the portenable command to enable the ports. For example: portenable 16-31 7. Optional: Enter the portshow command to verify that the newly activated ports are started. SAN Switch ISL Trunking groups All 8-Gb SAN Switch models support - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 27
trunking, see the Fabric OS Administrator's Guide for the firmware version you are running. Supported SFP transceiver options Table 2 lists the only SFPs supported in your HP StorageWorks 8-Gb SAN Switches. Table 2 Supported SFP transceiver options Switch product Port type Option Part number - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 28
accessed from the HP website: http://h18006.www1.hp.com/storage/networking/b_switches/san/index.html • HP StorageWorks Full Fabric Upgrade License • HP StorageWorks 8/8 and 8/24 SAN Switch 8-Gb 8-port Upgrade LTU • HP StorageWorks 8/80 SAN Switch 8-Gb 16-port Upgrade LTU • HP StorageWorks 8/40 SAN - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 29
HP StorageWorks Extension SAN Switch Advanced LTU • HP StorageWorks 1606 Extension SAN Switch FICON Control Unit Port LTU • HP StorageWorks 1606 Extension SAN Switch Integrated Routing LTU (purchase for 1606 Extension SAN Switch only) • HP 1606 Switch -B26 8-Gb SAN Switch Hardware Reference Guide 29 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 30
Hardware kit 50 m LC-SC multi-mode FC cable Order number 221691-B27 NOTE: For the latest information on hardware and software components, see the B-series Switches section of the HP Storage Networking website: http://www.hp.com/go/san. 30 HP StorageWorks 8-Gb SAN Switches - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 31
2 Installing and configuring an 8-Gb SAN Switch This chapter provides information about and instructions to install and configure an 8-Gb SAN Switch. Shipping carton contents Figure 13 and Table 4 identify shipping carton contents for a typical 8-Gb SAN Switch. The shipping configuration for your - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 32
kit, containing the following items: • HP StorageWorks product documentation: • HP StorageWorks 8-Gb SAN Switch Quick Start Instructions • HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions • Read Me First • Safety Guides • User License • Warranty • A serial cable, approximately - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 33
on the nonport side of the switch. The temperature inside the switch can be up to 80ºC (176ºF) during switch operation. If the internal temperature range exceeds the operating ranges of the components, the LEDs, error messages, and Fabric Watch alerts indicate a problem. Enter the tempshow or fabric - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 34
: For FCoE Converged Network Switches, both HP-branded FC SFPs and CEE 10-GbE SFPs are required. FC SFP+ transceivers are required for 8-Gb/s performance; copper cables must be HP-branded. • Access to an FTP server to back up the switch configuration (optional) Installing the switch as a standalone - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 35
switch to the network until the IP address is set. See "Setting the switch IP address" on page 46. Installing the switch using the SAN Switch Rack Mount Kit The SAN Switch Rack Mount Kit is supplied with your 8-Gb SAN Switch. Use the SAN Switch Rack Mount Kit for installations in the following HP - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 36
80 SAN Switches, FCoE Converged Network Switch, Encryption SAN Switch, and 1606 Extension SAN Switch NOTE: All devices require 10 screws except for the Encryption SAN Switch, 1606 Extension SAN Switch, and FCoE Converged Network Switch, which require only 6 screws. 36 Installing and configuring an - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 37
washers Two 1/4-inch flat washers CAUTION: For proper airflow, the SFP+ media side of the SAN Switch must face the rear of the rack. This allows air to enter the front of the rack and Table 5.) 2. Choose a mounting location for the device in the rack. 8-Gb SAN Switch Hardware Reference Guide 37 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 38
14. • For an HP System/e Rack, install the HP 10000 Series rack) . Figure 15 Installing the rear mounting brackets (HP System/e rack) . NOTE: The SAN Switch Rack Mount Kit contains rails labeled Left and Right to designate the left side and right side of the cabinet. 38 Installing and configuring - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 39
16. Do not tighten the nuts. Figure 16 Installing the outer rails (HP 10000 Series rack) . b. Depending on the rack you are using, complete one of the following tasks: • left rail. (See Figure 17.) Figure 17 Assembling the outer rails (HP 10000 Series rack) . 8-Gb SAN Switch Hardware Reference Guide 39 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 40
rails (HP System Switches, use the screw holes marked 16, as shown in Figure 20 on page 41. • To attach the inner rails to the FCoE Converged Network Switch, Encryption SAN Switch, or 1606 Extension SAN Switch, use two screw holes marked R and one screw hole marked 16. 40 Installing and configuring - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 41
. Attaching both rails requires six screws. This figure also applies to the Encryption SAN Switch, FCoE Converged Network Switch, and 1606 Extension SAN Switch. Figure 20 shows an inner rail attached to the 4/64 SAN Switch with five screws, using the rail screw holes marked 16. Attaching both rails - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 42
switch accessory kit: • 8/8 SAN Switch • 8/24 SAN Switch See "Installing the plenum" on page 42 for complete installation instructions. If you are installing a different device, see "Securing the switch to the outer rails" on page attach the plenum. 42 Installing and configuring an 8-Gb SAN Switch - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 43
racks) . Figure 23 Securing the device in an HP System/e Rack . 3. Tighten the hex nuts installed in step 4 of Installing the HP SAN Switch Rack Mount Kit in your HP custom rack, page 36. (See Figure 16, page 39.) This completes the rack mount procedure. 8-Gb SAN Switch Hardware Reference Guide 43 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 44
information, see the EZSwitch Setup CD or HP StorageWorks 8-Gb SAN Switch Quick Start Instructions, included with your 8-Gb SAN Switch. If you do not want to use EZSwitch Setup, use the procedures that follow. Obtaining required items To configure the SAN Switch for use in a network, ensure that you - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 45
For the 8/40 and 8/80 SAN Switches, Encryption SAN Switch, FCoE Converged Network Switch, and 1606 Extension SAN Switch, set the two AC switches to the ON position (1). Power is supplied to the switch as soon as the first power supply is connected and turned on. The power supply LEDs display amber - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 46
switch using the default password, (password). 2. Enter ipaddrset to set the Ethernet IP address. If you are going to use an IPv4 IP address, enter the IP address in dotted decimal notation as prompted: Ethernet IP Address: [192.168.74.102] If you are going to use an IPv6 address, enter the network - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 47
for the Encryption SAN Switch. For DCFM 10.3.0 and later, any DCFM version (Professional, Professional Plus, or Enterprise) is supported with encryption. Setting the domain ID To set the switch domain ID: 1. Using Telnet, log in to the switch as admin. 8-Gb SAN Switch Hardware Reference Guide 47 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 48
settings without completing all the prompts. 7. Re-enable the switch by entering the switchenable command. Setting the switch date and time The 8-Gb SAN Switch are used for logging, error detection, and troubleshooting. 1. Log in to the switch using the default password, (password). 2. Enter the date - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 49
zone on a switch updates the local time zone setup and is reflected in local time calculations. • By default, all switches are in the GMT time zone (0,0). If all switches in a fabric are in one time zone, you can keep the time zone setup at the default setting. • System services that have already - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 50
page 50. The parameters do not apply if the time zone for the switch has already been changed from the default (UTC). Because the time value is stored in nonvolatile memory, you need only set from UTC) -4,0 -3,0 -5,0 -4,0 -6,0 -5,0 -7,0 -6,0 -8,0 -7,0 50 Installing and configuring an 8-Gb SAN Switch - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 51
to a maximum of eight external NTP servers. To keep the time in your SAN current, HP recommends that the principal or primary FCS switch has its time synchronized with at least one external NTP server. The other switches in the fabric set their time automatically from the principal or primary FCS - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 52
1. Log in to the switch using the default password: password. 2. Enter the tsclockserver command: switch:admin> tsclockserver "" where ntp1 is the IP address or DNS name of the first NTP server, which the switch must be able to access. The second ntp2 is the second NTP server and is - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 53
it available for downloading to a replacement switch, if necessary. For instructions on backing up the configuration, see the Fabric OS Administrator's Guide. Changing the switch name and chassis name Changing the switch and chassis names is important for accurate tracking of errors in the RASlog - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 54
54 Installing and configuring an 8-Gb SAN Switch - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 55
SAN Switch the FCoE Converged Network Switch, and the 1606 Extension SAN Switch. Configuring the Encryption SAN Switch NOTE: For procedures to configure the encryption functions, including HP Secure Key Manager information, see the Fabric OS Encryption Administrator's Guide. For additional SKM setup - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 56
Ethernet Administrator's Guide. Configuring the 1606 Extension SAN Switch The following sections provide information on configuring the 1606 Extension SAN Switch. FCIP and Fibre Channel routing services configuration Initially, the FC ports on the 1606 Extension SAN Switch are set to persistently - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 57
operation To verify correct operation of the 1606 Extension SAN Switch: 1. Check the LEDs to verify that all components are functional (see "Port side LED activity for the 1606 Extension SAN Switch" on page 69). 2. Execute the portcfgpersistentenable command to activate the FC ports for FC operation - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 58
The LED states are as follows: • No light • Steady light • Flashing light The LEDs are either green or amber. 8/8 and 8/24 SAN Switch LEDs 8/8 and 8/24 SAN Switch LEDs are located on the port side only. 1. System power LED (green) 2. System status LED (green/amber) 3. Link status LED 4. Link speed - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 59
Figure 28. 1. System status LED (top) and system power (bottom) 2. Ethernet port status LEDs (green/amber) 3. FC port status (port 9) Figure 27 Identifying 8/40 SAN Switch port side LEDs . 1. Power supply 1 status LED 2. Power supply 2 status LED Figure 28 Identifying 8/40 SAN - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 60
LEDs are located on the port side and nonport side. See Figure 29 and Figure 30. 1. 8/80 SAN Switch 2. System status LED 3. Ethernet port 4. Ethernet speed LED 5. Ethernet link LED 6. FC port status LED (port 0) 7. FC port status LED (port 4) 8. FC ports (0 through 7) 9. FC - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 61
service provider. System is on and power supplies No action required. are functioning properly. System is off or there is no power. Verify that the system is on and has completed booting. System is on and functioning properly. No action required. 8-Gb SAN Switch Hardware Reference Guide 61 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 62
fan or power supply FRU is not the problem, do the following: 1. Connect a serial cable to the system and the error log for details on the cause of the status. Contact your switch service provider. disabled because of dia- Verify that the diagnostic tests are (flashing in 2-second gnostics or the - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 63
for the 8/80 SAN Switch Table 9 describes LEDs switched off. • Power cable is disconnected. • Power supply has failed. NOTE: When the switch fan FRU is seated. • Verify the switch is on. Steady green Steady amber (for fan FRU was disabled by the user. NOTE: When the switch is first powered on, the - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 64
LED is not green, the unit may be faulty. Contact your service provider. Steady green Ethernet link No light Steady green Ethernet activity (media or cable) is detected. • The switch is initializing. • A connected device is configured in an offline state. Do the following: • Verify the power - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 65
switch. incompatible switch connection. Fast flashing green Port is online and an internal (on 1/4 second, loopback diagnostic test ) Replace the SFP. Reset the port. No light Indicates one of the following: • Power supply FRU is switched off. • Power supply Switch Hardware Reference Guide 65 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 66
failed. • The fan FRU was disabled by the user. NOTE: When the switch is first powered on, the fan status LED shows Network Switch. There are two port status LEDs above each of the top row of ports. The left LED is for the top port, and the right LED is for the bottom port. See Figure 7 on page - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 67
Table 11 FCoE Converged Network Switch port side LED patterns been exceeded. Check the management interface and the error log for details on the cause of the status. Contact your switch service provider. Port speed is 10 Mb/s. No action action required. 8-Gb SAN Switch Hardware Reference Guide 67 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 68
Verify that the diagnostic tests are not running. Re-enable the port using the portenable command. Fast blinking amber Port failure (1/2 second) Check the management interface and the error log for details on the cause of the failure. Contact HP technical support, if necessary. Steady green - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 69
switch. Table 12 FCoE Converged Network Switch When the switch is first seated correctly. • Verify the switch is powered on. Fan assembly disabled. NOTE: When the switch is first powered on, the 1606 Extension SAN Switch. Figure 33 shows the LEDs on the port side of the 1606 Extension SAN Switch - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 70
problem unless the LEDs do not indicate a healthy state after all boot processes and diagnostic tests are complete. 1. System status LED 2. System power LED 3. Console port 4. Ethernet link LED 5. Ethernet status LED 6. Ethernet port 7. IP on the 1606 Extension SAN Switch . 70 Managing the 8-Gb SAN - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 71
1606 Extension SAN Switch is powered on (power supply switches are set to 1). • The power cables 4. Contact your switch service provider. Flashing error log for details on the cause of the status. Contact your switch service . • Connected device is configured in an offline state. Verify that the - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 72
the SFP or reset the switch from the workstation. GbE Copper Port Status 2 LEDs per port one green, one amber No lights (both LEDs Port is offline. are off) off, steady amber Port is faulty. Reset the switch from the workstation. If the problem persists, use the other copper port or the optical - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 73
whether any errors were detected: 1. Verify that the LEDs on the switch indicate that all components are healthy. (LED patterns are described in Table 8 on page 61 and Table 9 on page 63.) If one or more LEDs do not display a healthy state, do the following: a. Verify that the LEDs are not set to - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 74
physical maintenance. They include diagnostic tests and FRUs for the 8/40, 8/80, Encryption SAN Switch, FCoE Converged Network Switch, and 1606 Extension SAN Switch, as described in the following sections. Installing an SFP The 8-Gb SAN Switches support only HP-branded SFPs. For ordering information - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 75
troubleshoot the hardware and firmware. This includes tests of internal connections and circuitry, fixed media, and the transceivers and cables in use. The tests are implemented by command, either through a Telnet session or through a console set up to the serial connection to the switch. Some tests - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 76
Converged Network, and 1606 Extension SAN Switch FRU in the event of failure. Check the management interface and the error log for details on the cause of status. • In Web verify that the fan is seated correctly. If the light does not turn green, the fan assembly may need to be replaced. • In Web - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 77
40 SAN Switch power supply and fan assembly CAUTION: Disassembling any part of the power supply and fan assembly voids the warranty and regulatory certifications. There are no user-serviceable parts inside to the chassis by screwing in the captive screw. 8-Gb SAN Switch Hardware Reference Guide 77 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 78
the fan status using the fanshow command from the CLI. 8/80 SAN Switch and Encryption SAN Switch FRU units Replace the following FRUs as required: • Fan assembly • Power supply The 8/80 SAN Switch and Encryption SAN Switch integrate three fan assemblies (see Figure 36). Fabric OS identifies the fans - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 79
no user-serviceable parts inside the fan assembly. Because the cooling system relies on pressurized air, do not leave any of the fan assembly slots empty longer than two minutes while the switch is Fan assembly #1, Fan assembly #2, and Fan assembly #3). 8-Gb SAN Switch Hardware Reference Guide 79 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 80
6. Nonport side Figure 37 Inserting the fan assembly in the 8/80 SAN Switch . Replacing an 8/80 SAN Switch or Encryption SAN Switch power supply CAUTION: If a power supply fails, leave the power supply in the switch until it can be replaced. Maintain both power supplies in operational condition - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 81
green LED. 2. If the power supply you are replacing is not already powered off, press the AC power switch to power it off. 3. Unplug the power cord from the power supply you are replacing. 1. AC power receptacle with the AC power receptacle on the left. 8-Gb SAN Switch Hardware Reference Guide 81 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 82
If the light does not turn green, the power supply may switch. Table 16 lists the management tools available. When running IP over FC, these management tools must be supported by both HBA and HBA drivers. For a list of supported HBAs, see the HP StorageWorks SAN Design Reference Guide: http:// www.hp - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 83
Center Fabric Manager Enterprise User guide or the Brocade Data Center Fabric Manager Professional User guide. Ethernet or serial connection In-band support IP over FC IP over FC IP over FC IP over FC Native in-band interface (over HBA only) IP over FC 8-Gb SAN Switch Hardware Reference Guide 83 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 84
84 Managing the 8-Gb SAN Switches - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 85
8/80 SAN Switch 2U = 8.6 cm nl (3.4 inches) Encryption SAN Switch FCoE nl Converged nl Network nl Switch 2U = 8.6 cm nl (3.34 inches) 1U = 4.3 cm nl (1.7 inches) 1606 Extension SAN Switch 4.45 cm 8/8, 8/24, and 8/40 SAN Switch memory specifications. 8-Gb SAN Switch Hardware Reference Guide 85 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 86
Requirements 8/8, 8/24, 8/80, Encryption, and 1606 Extension SAN Switches-Primary AC input: 100-240 VAC, 2.0 A, 47-63 Hz; switch autosenses input voltage. 8/40 SAN Switch-Primary AC input: 90-264 VAC; switch autosenses input voltage. FCoE Converged Network Switch-Primary AC input: 85-264 VAC; input - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 87
ft/min). 8/8, 8/24, and 8/40 SAN Switches, FCoE Converged Network Switch, and 1606 Extension SAN Switch-One rack unit in a 48.3 cm (19 inch) cabinet. 8/80 and Encryption SAN Switches-Cabinet space of 2U in an EIA 19-inch or latest CNS 13438(95) or latest 8-Gb SAN Switch Hardware Reference Guide 87 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 88
hr In-rush current 8/8 and 8/24 SAN Switches: 21.5 A at 240 VAC cold start 8/40 SAN Switch: 15-35 A maximum 8/80 SAN Switch: 15 A maximum for period of 10-150 mS Encryption SAN Switch: Less than 60 A peak FCoE Converged Network Switch and 1606 Extension SAN Switch: Maximum of 60 A for period of 10 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 89
N/A N/A N/A N/A 10 km Table 25 Laser data transmission ranges for the 8/40 SAN Switch Port speed 1 Gb/s 2 Gb/s Cable HP Extended Fabrics license 50 to 100 km with an HP Extended Fabrics license 40 km (24.8 miles) 4 Gb/s 50 150 m (492 ft) N/A N/A 8-Gb SAN Switch Hardware Reference Guide - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 90
Switch, up to 500 km at 1 Gb/s is supported when using a long distance transport system such as DWDM. Table 26 Laser data transmission ranges for the 8/80 SAN Switch N/A 10 km (6.2 miles) without an HP Extended Fabrics license 50 to 100 km with an HP Extended Fabrics license 80 km (50 miles) - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 91
Switch, up to 500 km at 1 Gb/s is supported when using a long-distance transport system such as DWDM. Table 27 Laser data transmission ranges for the Encryption SAN Switch and FCoE Converged Network Switch (69 ft) N/A N/A N/A N/A N/A 10 km (6.2 miles) 8-Gb SAN Switch Hardware Reference Guide 91 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 92
Switch) Long wavelength (FCoE Converged Network Switch) NOTE: For the Encryption SAN Switch and FCoE Converged Network Switch, up to 500 km at 1 Gb/s is supported when using a long-distance transport system such as DWDM. Table 28 Laser data transmission ranges for the 1606 Extension SAN Switch - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 93
speed. POST and boot specifications The switch performs POST by default each time it is powered on or rebooted or the system is reset. Boot time with POST is usually Manual. POST The success/fail results of the diagnostic tests that run during POST can be monitored through LED activity, the error - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 94
Enables normal port operation Supported HBAs and CNAs NOTE: CNAs apply to the FCoE Converged Network Switch only. For a list of HBAs that have been tested and are known to work with the SAN switches, see the latest version of the HP StorageWorks SAN Design Reference Guide, at http://www.hp.com/go - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 95
's Guide 6.3.0 • Brocade Fabric OS Encryption Administrator's Guide • Brocade Converged Enhanced Ethernet Administrator's Guide You can find these documents on the Manuals page of the HP Business Support Center website: http://www.hp.com/support/manuals 8-Gb SAN Switch Hardware Reference Guide 95 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 96
, and then click HP StorageWorks DC SAN Director Switches to access the Manuals web page. The Brocade SAN Glossary provides definitions for SAN-related terminology used throughout this document. To access the glossary, see http://h20000.www2.hp.com/bc/docs/support/ SupportManual/c01429405/c01429405 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 97
Convention Blue text: Table 31 Blue, underlined text: http://www.hp.com Bold text Italic text Monospace text Monospace, italic text Monospace, or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. 8-Gb SAN Switch Hardware Reference Guide 97 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 98
convenience. Some parts do not qualify for CSR. Your HP-authorized service provider will determine whether a repair can be accomplished by CSR. For more information about CSR, contact your local service provider, or see the CSR website: http://www.hp.com/go/selfrepair 98 Support and other resources - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 99
laser device comply with safety standards, including IEC 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies as a Class 1 laser product. The product does not emit hazardous light. 8-Gb SAN Switch Hardware Reference Guide - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 100
to open the laser device enclosure. There are no user-serviceable components inside. • Do not operate controls, make adjustments, or perform procedures to the laser device other than those specified herein. • Allow only HP authorized service technicians to repair the laser device. Certification and - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 101
érique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. European Union regulatory notice Japanese notice 8-Gb SAN Switch Hardware Reference Guide 101 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 102
part designated for this product. For more information about battery replacement or proper disposal, contact an HP authorized service provider. WARNING! Your switch contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack. There is risk of fire and burns - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 103
disposal. Power cords The power cord set must meet the requirements for use in about the type of power cord to use, contact an HP authorized service provider. NOTE: Route power cords so that they will of waste equipment by users in private households in the Switch Hardware Reference Guide 103 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 104
information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service, or the shop where you purchased the product. Dutch notice Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie Dit - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 105
de recyclage des appareils mis au rebut, veuillez contacter les autorités locales de votre région, les services de collecte des ordures ménagères ou le magasin dans lequel vous avez acheté ce produit. oder im Geschäft, in dem Sie das Gerät erworben haben. 8-Gb SAN Switch Hardware Reference Guide 105 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 106
Greek notice Hungarian notice Italian notice Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 107
um ponto de coleta para reciclagem. A coleta e a reciclagem seletivas desse tipo de lixo ajudarão a conservar as reservas naturais; sendo assim, a reciclagem será feita 8-Gb SAN Switch Hardware Reference Guide 107 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 108
ambiente e a saúde das pessoas. Para obter mais informações sobre locais que reciclam esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o serviço de coleta de lixo ou com a loja em que o produto foi adquirido. Slovakian notice Slovenian notice Spanish notice Eliminaci - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 109
kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du köpte produkten för att få mer information om var du kan lämna ditt avfall för återvinning. 8-Gb SAN Switch Hardware Reference Guide 109 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 110
110 Regulatory compliance and safety - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 111
. If you do not have any of the suggested equipment for proper grounding, have an HP authorized reseller install the part. NOTE: For more information on static electricity, or for assistance with product installation, contact your HP authorized reseller. 8-Gb SAN Switch Hardware Reference Guide 111 - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 112
112 Electrostatic discharge - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 113
Inc. CEE CLI CN CNA C-series CSP CUP Converged Enhanced Ethernet. Command line interface. Converged Network. Converged Network Adapter. Fibre Channel switches and FICON directors manufactured for HP by Cisco Systems, Inc. Critical Security Parameter. Control unit port. An optional feature used to - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 114
System. EVA HP StorageWorks Enterprise Virtual network of one or more Fibre Channel switches that transmit data between any two N_Ports on any of the switches. An automatic method for transferring operations from a failed system to a secondary, identical system. Fibre Channel. A comprehensive set - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 115
gate array. Fabric Provided Mac Addressing. Field-replaceable unit. Services Module. Integrated routing. Internet Small Computer System Interface. A standard protocol that uses SCSI commands to transfer data over IP networks. Interswitch link. A connection between two directors or switches - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 116
. Synonymous with WWPN. Quality of service. A traffic management feature. Reliability, availability, and serviceability. Reliable commit service. A Fabric OS feature. Reduced Instruction Set Computer. Real-time clock. Storage area network. An intelligent infrastructure that connects heterogeneous - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 117
Storage Networking Industry Association. Storage Optimized Transmission Control Protocol. Service pack. A collection of software updates. Single Point of Connectivity Knowledge. An HP website as the primary portal to obtain detailed information about supported HP StorageWorks product configurations - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 118
zone Wavelength division multiplexing. The technique of placing multiple optical signals on a single optical cable simultaneously. HP StorageWorks product consisting of two or more XP disk arrays performing disk-to-disk replication, and a management user interface that facilitates configuring - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 119
Index Symbols 1606 Extension SAN switch configuring, 56 features, 21 FRUs, 76 LED activity, 69 verifying operation, 57 8-Gb SAN switches hardware options, 29 ISL trunking groups, 26 management features, 82 powering off, 45 powering on, 44 software options, 28 8-Gb SAN switches installing and - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 120
configuring 1606 Extension SAN switch, 56 cabling and configuring, 44 connecting an Ethernet cable, 47 correcting time zone, 50 ezswitch setup, 44 FCoE Converged Network Switch, 56 making a serial connection, 45 opening a Telnet session, 47 SAN encryption switch, 55 setting time zone, 49 setting - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 121
FRUs, 75 IP address, setting, 46 ipaddrshow command, 47 ISL trunking groups, 26 L LEDs 1606 Extension SAN switch, 69 8/24 SAN switch, 58 8/40 SAN Switch, 59 8/8 SAN switch, 58 8/80 SAN switch, 60 Encryption SAN switch, 64 fan assembly, 77 FCoE Converged Network switch , 66 licenseadd command - HP 1606 | HP StorageWorks 8-Gb SAN Switch Hardware Reference Guide (5697-0291, J - Page 122
support HP, 95 technical specifications, 85 technical support service locator website, 96 Telnet session opening, 47 text symbols, 97 time zones correcting, 50 setting, 49 W warning rack stability, 96 websites customer self repair, 98 HP , 96 HP Subscriber's Choice for Business, 95 product manuals
HP StorageWorks
8-Gb SAN Switch Hardware Reference Guide
Abstract
This document provides information on installing, configuring, and maintaining the 8-Gb SAN family of HP
StorageWorks Fibre Channel switches. This document is intended for system administrators and technicians with
knowledge of SANs and HP StorageWorks Fibre Channel switches.
Part Number: 5697-0291
Sixth edition: July 2010