HP 2.8kVA 120 Volt L5-30 Input 12xNEMA HP Basic Power Distribution Unit Instal
HP 2.8kVA 120 Volt L5-30 Input 12xNEMA Manual
 |
View all HP 2.8kVA 120 Volt L5-30 Input 12xNEMA manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 2.8kVA 120 Volt L5-30 Input 12xNEMA manual content summary:
- HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 1
HP Basic Power Distribution Unit Installation Guide Abstract This document is for the person who installs and maintains HP PDU products. HP assumes you are qualified in the installation of electrical equipment - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 2
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 3
Contents Before you begin ...4 Overview ...4 Safety and regulatory compliance...4 Important safety information ...4 Required tools ...5 Additional requirements ...5 Recommended hardware configurations 6 Configurations ...6 Hardware installation ...9 Installing the PDU ...9 Installing 1U and 0U PDUs - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 4
document provides installation instructions for qualified available on the HP website (http://www.hp.com/support/importantsafetyinformation). This PDU is intended only for ITE loads The installation of options and routine maintenance and service of this product must be performed by individuals - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 5
WARNING: To reduce the risk of personal injury from high-leakage current, verify earth connection before connecting the power supply. The summation of input power for multiple pieces of information technology equipment through the use of power products can result in high-leakage currents. If the - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 6
Recommended hardware configurations Configurations The PDU is installed in a rack in the following configurations: • A single PDU configuration, with the outlets facing the center of the rack • A single PDU configuration, with the outlets facing the rear of the rack Recommended hardware - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 7
• A double PDU configuration, with the outlets facing the center of the rack • An inverted PDU, with the input power cable exiting the top of the rack Recommended hardware configurations 7 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 8
• 1U and 0U configurations Recommended hardware configurations 8 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 9
Hardware installation Installing the PDU 1. Align and install the power cord retention bracket with the screw holes marked "C." 2. Align and install the mounting pins with the screw holes marked "M." Hardware installation 9 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 10
3. If installing the PDU inverted, install a mounting pin on the bottom of the PDU. 4. If needed, install the input power cable retention band. Hardware installation 10 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 11
5. If needed, insert and secure the power cable. 6. Install the PDU and ensure the mounting pins are engaged with the rack. CAUTION: When moving a rack with installed components, always use the shipping bracket to secure the PDU. Hardware installation 11 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 12
7. If the PDU is not inverted, install the shipping bracket above the PDU. 8. If the PDU is installed above 39U, flip the PDU shipping bracket to allow space for the rack shipping bracket. Hardware installation 12 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 13
9. If the PDU is inverted, install the shipping bracket over the mounting pin below the PDU. Installing 1U and 0U PDUs 1. Attach the power cord retention bracket. Hardware installation 13 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 14
2. Attach the appropriate mounting brackets. Each bracket only requires two screws per side for this product. o 1U bracket installation o 0U bracket installation 3. Install cage nuts. Hardware installation 14 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 15
4. Install the PDU: o 1U installation o 0U installation Hardware installation 15 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 16
Securing the cables Secure the cable weight to the retention bracket. The installation is complete. Hardware installation 16 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 17
Acronyms and abbreviations AC alternating current ITE Information Technology Equipment kVA kilovolt-ampere PDU power distribution unit PFC power factor corrected Acronyms and abbreviations 17 - HP 2.8kVA 120 Volt L5-30 Input 12xNEMA | HP Basic Power Distribution Unit Instal - Page 18
Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:[email protected]). Include the document title and part number, version number, or the URL when
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
HP Basic Power Distribution Unit
Installation Guide
Abstract
This document is for the person who installs and maintains HP PDU products. HP assumes you are qualified in the installation of electrical equipment
and trained in recognizing hazards in products with hazardous energy levels.
Part Number: 720595-002
May 2013
Edition: 2