HP 2200 HP LaserJet 2200 Series - User Guide - Page 101

Wireless Printing Problems continued, Symptom, Possible Cause, Solution, The connection may

Get HP 2200 - LaserJet B/W Laser Printer PDF manuals and user guides View all HP 2200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

Wireless Printing Problems (continued) Symptom Possible Cause Solution The connection cannot be established or the transmission seems to be taking longer than usual (continued). Bright lights are interfering with the signal. Make sure that no bright light is shining directly into either IR port. Bright light of any kind (sunlight, incandescent light, fluorescent light, or light from an infrared remote control, such as those used for TVs and VCRs) shining directly into one of the IR ports may cause interference. Position the device closer to the IR port on the printer. The printer prints only part of a The connection has been page or document. interrupted during transmission. IrDA-compliant devices are designed to recover from temporary connection interruptions. Re-establish the connection. (Depending on the device you are using, it can take anywhere from 3 to 40 seconds to re-establish the connection.) The print job has been The connection may have properly sent to the printer, but been disrupted or broken. the printer will not print. If the connection is broken before the print job has started, the printer may not print any of the job. If the Ready (middle) light is on, press JOB CANCEL to clear the printer memory. Position the device within the range of operation and print the job again. The FIR status light turns off The connection may have during transmission. been broken. If the Ready (middle) light is on, press JOB CANCEL to clear the printer memory. Position the device within the range of operation and print the job again. ENWW Chapter 4 Problem Solving 91

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
ENWW
Chapter 4 Problem Solving
91
The connection cannot be
established or the
transmission seems to be
taking longer than usual
(continued).
Bright lights are interfering
with the signal.
Make sure that no bright light
is shining directly into either IR
port. Bright light of any kind
(sunlight, incandescent light,
fluorescent light, or light from
an infrared remote control,
such as those used for TVs
and VCRs) shining directly into
one of the IR ports may cause
interference. Position the
device closer to the IR port on
the printer.
The printer prints only part of a
page or document.
The connection has been
interrupted during
transmission.
IrDA-compliant devices are
designed to recover from
temporary connection
interruptions. Re-establish the
connection. (Depending on the
device you are using, it can
take anywhere from 3 to 40
seconds to re-establish the
connection.)
The print job has been
properly sent to the printer, but
the printer will not print.
The connection may have
been disrupted or broken.
If the connection is broken
before the print job has
started, the printer may not
print any of the job. If the
Ready (middle) light is on,
press
J
OB
C
ANCEL
to clear the
printer memory. Position the
device within the range of
operation and print the job
again.
The FIR status light turns off
during transmission.
The connection may have
been broken.
If the Ready (middle) light is
on, press
J
OB
C
ANCEL
to clear
the printer memory. Position
the device within the range of
operation and print the job
again.
Wireless Printing Problems (continued)
Symptom
Possible Cause
Solution