HP 4300n HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit
HP 4300n - LaserJet B/W Laser Printer Manual
 |
UPC - 808736314381
View all HP 4300n manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 4300n manual content summary:
- HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 1
q2429a •q2430a• q2436a• q2437a maintain maintenance wartung manutenzione mantenimiento lea esto primero - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 2
fuser, one transfer roller, one plastic transfer-roller tool, one pickup roller, six feed rollers, and one pair of disposable gloves. Depending upon which optional accessories are installed, you might not need all of these parts. Note: The cost of this kit is not covered under the original printer - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 3
duplexer, if it is installed. Disconnect all cables from the rear of the printer. To replace the transfer roller: Turn the printer so that the front is facing you. Open the top cover and remove the print cartridge stampante in modo da visualizzare la parte anteriore. Aprire il coperchio superiore - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 4
from the new transfer roller. CAUTION: Do not touch the new transfer roller with bare hands. Skin oils on the roller can cause print-quality problems. Make sure that the black collar on the left side is oriented properly, with the open end down. Install the new transfer roller by sliding - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 5
8 9 10 1 2 Install the print cartridge, and then close the top cover. To replace the tray-1 pickup roller: If an optional envelope feeder is installed, remove it by pressing the envelope- - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 6
12 13 Locate located on each side of the opening. Slide the roller into the printer until the roller snaps into place. Repérez le rouleau d'entraî en bas du rouleau, de chaque côté, sur la fente du support situé de part et d'autre de l'ouverture. Faites glisser le rouleau dans l'imprimante - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 7
14 15 16 1 1 2 2 Insert the envelope-entrance cover (1) or the optional envelope feeder (2). To replace the feed rollers in tray 2: Remove tray 2 from the printer. Find the cover that is located on the tray, next to the feed roller. Open the cover by rotating it upward. Pinch the blue latch - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 8
located inside the printer. WARNING! Do not allow the front of the printer to extend beyond the edge of the table. The printer can become unbalanced sbilanciarsi e cadere, provocando lesioni personali o subendo dei danni. Mueva la parte frontal de la impresora hasta el borde de la mesa para tener - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 9
20 21 22 Slide a new feed roller onto the shaft and rotate the roller until it locks into place. Note: It is important that the roller locks into place. Insert tray 2. If no optional trays are installed, go to step 31. To replace the feed rollers in an optional 500-sheet feeder: If an optional - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 10
Altrimenti, passare alle istruzioni al punto 31. Premere la leva di rilascio ed aprire lo sportello dell'alimentatore da 1500 fogli. Nella parte interna dello sportello, aprire lo sportello più piccolo accanto al rullo di alimentazione. Para sustituir los rodillos alimentadores en un alimentador - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 11
el espaciador negro y redondo situado junto al rodillo está colocado adecuadamente y encaja en el pasador del eje. El rodillo está situado en la parte central superior dentro del alimentador de 1500 hojas. Apriete la palanca azul que está situada en el lado izquierdo del rodillo (1). Extraiga el - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 12
it locks into place. Note: It is important that the roller locks into place. Close the door of the 1500-sheet feeder. To replace the fuser: Open the rear output bin and pull the extension outward until it stops. Faites glisser un nouveau rouleau d'alimentation sur l'axe. Faites-le pivoter jusqu - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 13
fuser straight out of the printer. WARNING! The fuser might be hot. Make sure that the printer has been turned off for 30 minutes before removing the fuser. Remove all packing material from the new fuser e l'estensione piegando verso il basso la parte centrale dello scomparto e rilasciando i due - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 14
fuser firmly into the printer until the blue levers on both sides click into place. Install the rear output bin. Pull gently on the bin to make sure that the hinge pins are fully inserted. Connect the cables to the rear of the printer parte posterior de la impresora. Deutsch Italiano Español 13 - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 15
38 39 40 Install the optional duplexer, if it was removed. To finish the installation: Turn the printer power on while holding down for several seconds, until all three control panel lights turn on and remain on. Press until the NEW MAINTENANCE KIT message appears on the display, and then press - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 16
maintenance" is reset to zero. If the number is not reset, repeat step 39, or see the support flyer that came with the printer. Note: If any kit components were improperly installed or not completely seated, jams can occur. If you purchased an exchangeable kit, you can return your old fuser to HP - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 17
16 - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 18
17 - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 19
18 - HP 4300n | HP q2429a, q2430a, q2436a, q2437a - Maintenance Kit - Page 20
copyright © 2002 Hewlett-Packard Company www.hp.com *Q2436-90901* *Q2436-90901* Q2436-90901
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
 |
 |
maintain
maintenance
wartung
manutenzione
mantenimiento
lea esto primero
q2429a
•
q2430a
•
q2436a
•
q2437a