HP 8/20q HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction
HP 8/20q Manual
View all HP 8/20q manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 8/20q manual content summary:
- HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 1
HP StorageWorks 8/20q Fibre Channel Switch Rack-Mount Kit quick start installation instructions • One HP StorageWorks Simple SAN Connection Manager software CD, which includes HP • One Ethernet port • One or more PCIe slots for the HP StorageWorks 81Q PCIe FC HBA (or other supported QLogic FC HBA) • - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 2
in a 19" EIA rack following the steps in the HP StorageWorks 8/20q Fibre Channel Switch Rack-Mount Kit quick start installation instructions. 2. Install each SFP transceiver by inserting the transceiver into any of the active switch ports and pressing gently until it snaps in place. The transceiver - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 3
installation instructions. For configuration of servers using non-QLogic HBAs or other operating systems, refer to the HP StorageWorks Simple SAN Connection Manager user guide. IMPORTANT: Simple SAN Connection Manager version 2.10 or later can manage HP StorageWorks 8/20q Fibre Channel Switches - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 4
growth requirements. • HP SAN Visibility is a SAN data analysis tool that securely analyzes your SAN configuration, providing an automated inventory process for switches, HBAs, and storage systems, including firmware version verification. 5. Click Install. Figure 7 Installation wizard: progress - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 5
When the first component, the HP FC driver, is installed, a diagnostic window (Figure 8) shows the HBA properties and targets found. your EVA), select one to add to the HP Storage Admin group. Then click Add To Group. When prompted, enter a password for the existing user account, and then click OK. - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 6
) When the first component, the HP FC driver, is installed, a diagnostic window (see Figure 8 on page 5) shows the HBA properties and targets found. 6. Click OK to close the SAN diagnostics window and continue the installation. The message Your installation is complete is displayed (see Figure - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 7
opens. This dialog box guides you through setting the switch IP address, administrator password, and default zoning. For details, refer to the "Getting started" section of the HP StorageWorks Simple SAN Connection Manager user guide. If the switch is already configured, the New Switch Setup does not - HP 8/20q | HP StorageWorks 8Gb Simple SAN Connection Kit quick start instruction - Page 8
14 New Switch Setup wizard Figure 15 shows an example of the main window for Simple SAN Connection Manager. Figure 15 Simple SAN Connection Manager main window For assistance with this software, refer to the HP StorageWorks Simple SAN Connection Manager user guide, available online at www.hp.com/go
Page 1
*5697-0082*
Congratulations on your purchase of the 8Gb
Simple SAN Connection Kit. This document
provides procedures for installing the kit
components, including the HP StorageWorks
8/20q Fibre Channel Switch, the host bus
adapters (HBAs), and the HP StorageWorks
Simple SAN Connection Manager (Simple SAN
Connection Manager) software bundle on a
Windows or Linux system.
Verify contents and requirements
1.
Verify the package contents.
The 8Gb Simple SAN Connection Kit is shipped with the
following items and quantities:
• One
quick start instructions
(this document)
• One
Read-Me-First
document
• One
End User License Agreement
(EULA)
• One
HP StorageWorks 8/20q Fibre Channel Switch
Rack-Mount Kit quick start installation instructions
•
One HP StorageWorks Simple SAN Connection Manager
software CD, which includes HP Enterprise Virtual Array (EVA)
Management, Modular Smart Array (MSA) Management,
and other related software components
•
One HP StorageWorks 8/20q Fibre Channel Switch
•
One HP StorageWorks 8/20q Fibre Channel Switch
Rack-Mount Kit
•
Four rubber mounting feet for the HP StorageWorks 8/20q
Fibre Channel Switch (for desktop placement, if you are not
using the rack-mount kit)
•
Ten 8 Gb shortwave fiber optic transceivers
•
Six 5m LC-LC Multi-Mode Fibre Channel (FC) cables
•
Four 8 Gb HP StorageWorks 81Q PCI Express (PCIe) Fibre
Channel HBAs (PCIe x8 physical connector)
•
Four low-profile HBA mounting brackets
•
One standard power cord
•
One HP Power Distribution Unit (PDU) power cable
•
One serial cable
2.
Verify that the server running your management software
(management station) meets the following minimum requirements
for supporting the software (including Simple SAN Connection
Manager and other HP software):
•
Operating system:
•
Windows Server 2003 R2 x64/x86 with SP2 and
Microsoft hotfix QFE932755 (updated Storport storage
driver). The update is available on the Microsoft website:
.
•
Windows Server 2008 x64/x86 with SP1 or later.
•
512 MB of memory
•
200 MB of disk space
•
One 2.0 GHz processor
•
One CD-ROM drive
•
One Ethernet port
•
One or more PCIe slots for the HP StorageWorks 81Q PCIe
FC HBA (or other supported QLogic FC HBA)
•
Java Runtime Environment (JRE) x86 1.5 or later
© Copyright 2008–2009 Hewlett-Packard Development Company,
L.P.
Fifth edition: July 2009
Product names mentioned herein may be trademarks of their
respective companies.
The information in this document is subject to change without notice.
Microsoft and Windows are U.S. registered trademarks of Microsoft
Corporation.
Java is a U.S. trademark of Sun Microsystems, Inc.
Printed in the U.S.
www.hp.com
HP StorageWorks
8Gb Simple SAN Connection
Kit quick start instructions