HP 8200 HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual
HP 8200 - ScanJet Digital Flatbed Scanner Manual
View all HP 8200 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP 8200 manual content summary:
- HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 1
hp scanjet 8200/8250/8290 scanner - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 2
also clean the underside of the glass. Cleaning the underside of the glass requires you to disassemble the scanner. For instructions on cleaning the underside of your scanner glass, click on the name of your scanner model. Perform this procedure only if it is absolutely necessary. Disassemble the - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 3
needed: • phillips screwdriver • small flat blade screw driver Supplies needed: • Glass cleaner • lint-free cloths 1 Disconnect the USB cable between the scanner and computer. 2 Disconnect the power supply from the scanner. Wait at least 15 minutes (after disconnecting power) before dissembling the - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 4
disassembly remove the scanner TMA After steps 1 and 2 have been completed and the scanner has cooled for 15 minutes, you can remove the TMA as shown. 3 Unplug the TMA and open the lid and lift it straight up. Unplug TMA Scanner lid being removed Scanner components: • TMA (1) • scanner top cover (2) - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 5
and the plastic it could stain the calibration strip ( the white strip under the glass) and render your scanner useless. If the cleaner gets in the calibration strip area, the scanner must be sent to hp for repair. 5 Apply glass cleaner to a soft lint-free cloth. Clean the plastic first. 6 Apply the - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 6
7 Using a flat blade screwdriver pry up the button panel cover and remove it. Then Use a Phillips screwdriver and remove the four screws from the bottom of the scanner. See the following illustration for the location of the screws. Removing the Button Panel location of the screws 8 Remove the screws - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 7
• top cover (1) • base (2) remove the top cover After unscrewing the top cover, you are ready to remove it by lifting the rear of the scanner first, then sliding away from the front . top cover being removed 9 Carefully lift the top cover off the base. Lift the back of the top - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 8
glass and the plastic it could stain the calibration strip ( the white strip under the glass) and render your scanner useless. If the cleaner gets in the calibration strip area, the scanner must be sent to hp for repair. 10 Apply glass cleaner sparingly to a soft, lint-free cloth and clean the glass - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 9
screws 12 Re-insert and tighten the four screws with a Phillips screwdriver. Step #7 Insert the screws location of screws insert the scanner TMA you can now re-insert the scanner TMA, with the lid in the open position. 14 Align the lid hinges with the slots of the top cover and slide - HP 8200 | HP Scanjet 8200 series scanner - (English) Glass Cleaning Manual - Page 10
reconnect your scanner You can now reconnect the USB cable and the power supply to the scanner. For instructions on connecting the cables see the setup instructions that came with your scanner.
hp scanjet 8200/8250/8290 scanner