HP A1210n Upgrading and Servicing Guide

HP A1210n - Pavilion - 512 MB RAM Manual

Get HP A1210n - Pavilion - 512 MB RAM PDF manuals and user guides View all HP A1210n manuals
Add to My Manuals
Save this manual to your list of manuals

HP A1210n manual content summary:

  • HP A1210n | Upgrading and Servicing Guide - Page 1
    Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 2
    No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of HP. uses only. Microsoft and Windows are U.S. Registered trademarks of Microsoft Corporation. HP supports lawful use of technology and does not endorse or encourage the use
  • HP A1210n | Upgrading and Servicing Guide - Page 3
    Replacing Drives 3 Removing a Drive 4 Replacing or Adding a Drive 5 Adding Memory 7 Removing a Memory Module 7 Installing a Memory Module 8 Removing or Installing an Add-In Card 8 Removing an Add-In Card 9 Installing an Add-In Card 9 Replacing the Battery 10 Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 4
    iv Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 5
    upgrade or service the PC. • These procedures assume familiarity with the general terminology associated with personal computers and with the safety practices and regulatory compliance required for using and modifying electronic equipment. Before Opening the PC 1 Remove any diskette or optical disc
  • HP A1210n | Upgrading and Servicing Guide - Page 6
    an Ethernet connector). 2 Reconnect the modem/telephone cable, and all other cables (such as the keyboard, mouse, and monitor) and external devices. 3 Turn on the PC and all peripherals. 4 If you installed an add-in card, install any software drivers supplied by the card manufacturer. Removing the
  • HP A1210n | Upgrading and Servicing Guide - Page 7
    (blank plate) or a CD-ROM, CD-RW, DVD-ROM, DVD+RW/+R, or combination drive C Memory card reader (select models) D Diskette (floppy) drive (select models) E Front connector panel (no replacement instructions) F Hard disk drive G Second hard disk drive (select models) Upgrading and Servicing Guide 3
  • HP A1210n | Upgrading and Servicing Guide - Page 8
    For a second hard disk drive, remove the two screws (3) and then slide the drive part way back out of the bay (4). Disconnecting the Optical Drive Cables Disconnecting the Memory Card Reader Drive Cable Removing the Second Hard Disk Drive 4 Upgrading and Servicing Guide Disconnecting the Diskette
  • HP A1210n | Upgrading and Servicing Guide - Page 9
    Parallel ATA Hard Disk Drive Cables 5 Pull the drive out of the drive bay. 6 If you are replacing the old drive with a new drive, remove the four guide screws (two on each side) from the old drive. You need these screws to install the new drive. Replacing or Adding a Drive 1 If necessary, remove the
  • HP A1210n | Upgrading and Servicing Guide - Page 10
    to your drive as indicated in the following illustrations. If it is present, reconnect the sound cable. Connecting the Optical Drive Cables NOTE: An optical drive may include a sound cable. Connect this cable also. Connecting the Serial ATA Hard Disk Drive Cables 6 Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 11
    and speed of memory module your PC uses, and for specific memory module information and specifications, go to the Web site listed in your Warranty and Support Guide and click the Support link. WARNING: Using the wrong type of memory module could damage the system. Removing a Memory Module 1 Complete
  • HP A1210n | Upgrading and Servicing Guide - Page 12
    each board/card in the computer. The total +5 V current draw in a fully loaded system (one with all add-in card slots filled) must not exceed the total number of slots multiplied by 2 amps. A Phillips screwdriver is needed to remove, replace, or add an add-in card. 8 Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 13
    and close the PC. See "Opening and Closing the PC" on page 1. NOTE: If the new card or device isn't working, read through the card manufacturer's installation instructions, and recheck all connections, including those to the card, power supply, keyboard, and monitor. Upgrading and Servicing Guide 9
  • HP A1210n | Upgrading and Servicing Guide - Page 14
    CR2032 battery in the socket, with the positive (+) side facing the latch. 7 Replace memory modules or cables you removed. 8 Set the chassis upright. 9 Complete the procedures to replace the side panel, and to close the PC. See "Opening and Closing the PC" on page 1. 10 Upgrading and Servicing Guide
  • HP A1210n | Upgrading and Servicing Guide - Page 15
    Upgrading and Servicing Guide 11
  • HP A1210n | Upgrading and Servicing Guide - Page 16
    Printed in
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Upgrading and Servicing Guide