HP AA979A HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions
HP AA979A - StorageWorks SAN Switch 2/8V Manual
UPC - 829160154480
View all HP AA979A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP AA979A manual content summary:
- HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 1
HP StorageWorks SAN Switch rack mount kit installation instructions Sixth Edition (May 2007) *A7511-90902* Part Number: *A7511-90902* - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 2
are set forth in the express limited warranty statements for such products. Nothing herein should be construed as constituting an additional warranty. Printed in the U.S.A. SAN Switch rack mount kit installation instructions Sixth Edition (May 2007) Part Number: *A7511-90902 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 3
(SAN) switches and routers. Supported Devices Use the SAN Switch Rack Mount Kit to install the following HP StorageWorks switches and routers only: ■ SAN Switch 2/8V, SAN Switch 2/16V ■ SAN Switch 2/32 ■ SAN Switch 4/32 ■ 4/8 SAN Switch ■ 4/16 SAN Switch ■ 4/64 SAN Switch ■ 4/32B SAN Switch ■ Multi - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 4
plenum ships with the following devices only: ■ SAN Switch 2/8V ■ SAN Switch 2/16 ■ SAN Switch 2/16V ■ 4/8 SAN Switch ■ 4/16 SAN Switch ■ 4/32B SAN Switch See Installing the Plenum (if required), page 17 for complete instructions on how to install a plenum. 4 SAN Switch rack mount kit installation - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 5
inches (48.3 cm) wide, and at least 23 inches (68.6 cm) deep. For the MP Router or 4/64 SAN Switch, plan a rack space that is at least 2 units high. ■ Ground all equipment in the rack through a reliable overheating, which may cause it to fail. SAN Switch rack mount kit installation instructions 5 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 6
HP 9000 Series, HP 10000 Series, HP 10000 G2 Series or HP System/e rack. Note: The SAN Switch Rack Mount Kit installation requires one technician. Required Tools and Hardware Obtain the following items: ■ #2 Phillips screwdriver ■ 7/16-inch wrench or socket ■ HP StorageWorks device, see Supported - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 7
Table 1: Hardware included in the SAN Switch Rack Mount Kit (Continued) Item Description Fourteen (14) #8-32 x 3/16-inch Phillips pan-head adapter washers Two (2) 1/4-20 hex nuts with captive star lock washers Two (2) 1/4-inch flat washers SAN Switch rack mount kit installation instructions 7 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 8
To install the HP StorageWorks device in a rack: Note: Figures and procedures throughout this document use "HP 10000 Series Rack" to reference both 10000 Series rack models (HP 10000 Series Rack and HP 10000 G2 Series Rack). 1. Check the contents of the SAN Switch Rack Mount Kit shipping carton to - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 9
brackets with two #10-32 x 1/2-inch Phillips pan-head screws and two #10 alignment washers as shown in Figure 2. Figure 2: Installing the Rear Mounting Brackets (HP System/e Rack) Note: Your SAN Switch Rack Mount Kit contains both left rails and right rails. The rails are labelled Right and Left - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 10
hex nuts loosely (as shown in Figure 3). Do not tighten; tighten the hex nuts later in step 3 on page 19. Figure 3: Installing the Outer Rails (HP 10000 Series Racks) 10 SAN Switch rack mount kit installation instructions - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 11
on the rack you are using, complete one of the following tasks: - For HP 10000 Series racks, install two #10-32 x 1/2-inch Phillips pan-head screws left rail, as shown in Figure 4. Figure 4: Assembling the Outer Rails (HP 10000 Series Racks) SAN Switch rack mount kit installation instructions 11 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 12
- For an HP System/e rack, install two #10-32 x 1/2-inch Phillips pan-head screws with captive star lock washers and and lower hole locations of the left rail, as shown in Figure 5. Figure 5: Assembling the Outer Rails (HP System/e Rack) 12 SAN Switch rack mount kit installation instructions - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 13
your specific device as follows: a. To attach the inner rails to the SAN Switch 2/16, SAN Switch 2/8V, or SAN Switch 2/16V use the screw holes marked 8. b. To attach the inner rails to the 4/8 and 4/16 SAN Switches, use the screw holes marked 8. SAN Switch rack mount kit installation instructions - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 14
To attach the inner rails to the SAN Switch 4/32, 4/32B SAN Switch, 4/64 SAN Switch or the 400 MP Router use the 8 when attaching the inner rails to the SAN Switch 2/16V or SAN Switch 2/16N. 7. Assemble the two inner rails attached to the 4/64 SAN Switch with five screws using the rail screw holes - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 15
Hz DC OK AC OK Figure 6: Attaching the Inner Rails to an MP Router MRO25007a ! IOIOI SPD LNK Figure 7: Attaching the Inner Rails to a 4/64 SAN Switch SAN Switch rack mount kit installation instructions MRO25018b 15 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 16
in the accessory kit with the rack mount hardware: ■ SAN Switch 2/8V ■ SAN Switch 2/16 ■ SAN Switch 2/16V ■ 4/8 SAN Switch ■ 4/16 SAN Switch ■ 4/32B SAN Switch See Installing the Plenum (if required), page 17 for complete installation instructions. If not installing one of the devices listed in step - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 17
8 include the plenum (1), a switch (2), and the screws that attach the rails to the plenum (3). 1 2 IOIOI ! 3 mMAoaTuxTnimtEinugmNtoTscbIrOeew5Nmle:mngothr 1fo3r/6ra4cikn. Figure 8: Attaching the Plenum to a 4/8 or 4/16 SAN Switch SAN Switch rack mount kit installation instructions 25052a 17 - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 18
the outer rails. Note: This step applies to installing a switch in HP 9000 Series, HP 10000 Series or HP System/e racks. 2. Insert the device into the rack and install Figure 9: Securing the Device (in HP 9000 Series or HP 10000 Series Racks) 18 SAN Switch rack mount kit installation instructions - HP AA979A | HP StorageWorks SAN Switch Rack Mount Kit Installation Instructions - Page 19
#10-32 x 1/2-inch Phillips pan head screw with captive star lock washer from either side of the rack uprights. This completes the rack mount procedure. SAN Switch rack mount kit installation instructions 19
HP StorageWorks
SAN Switch
rack mount kit
installation instructions
Sixth Edition (May 2007)
*A7511-90902*
Part Number:
*A7511-90902*