HP AD510A HP StorageWorks Controller Power Supply Replacement Instructions (56
HP AD510A - StorageWorks Modular Smart Array 1500 cs 2U Fibre Channel SAN Attach Controller Shelf Hard Drive Manual
 |
UPC - 829160218625
View all HP AD510A manuals
Add to My Manuals
Save this manual to your list of manuals |
HP AD510A manual content summary:
- HP AD510A | HP StorageWorks Controller Power Supply Replacement Instructions (56 - Page 1
HP StorageWorks Controller power supply replacement instructions Parts can be damaged by electrostatic discharge. Use proper anti-static protection. • Have a copy of the product user guide available for reference. You can download a copy of the user guide from the product support page on the HP - HP AD510A | HP StorageWorks Controller Power Supply Replacement Instructions (56 - Page 2
status indicator, or if either HP Command View EVA or your system monitoring tool indicates multiple hardware failures, contact HP support for assistance (http://www.hp.com/support). • Analyze any failure messages received. • Check status using HP Command View EVA: 1. In the Navigation pane, select - HP AD510A | HP StorageWorks Controller Power Supply Replacement Instructions (56 - Page 3
BOX # POWER SUPPLY OK • From HP Command View EVA on an EVA product: • Navigate to the component and check the status. It should be . • Turn off the locate function by clicking Locate > Locate Off. Returning the failed component Follow the return instructions provided with the new component. Page
-
1 -
2 -
3
 |
 |
HP StorageWorks
Controller power supply
replacement instructions
These instructions apply to the MSA1500cs, MSA20,
and EVA4x00/6x00/8x00 products. The part
may also be used in other HP products. See the
documentation for your speci
fi
c product for detailed
replacement instructions.
© Copyright 2005 Hewlett-Packard Development Company, L.P.
Fourth edition June 2007
The information in this document is subject to change without
notice.
Printed in Puerto Rico
www.hp.com
*5697-6789*
About this document
This document describes the procedure for replacing the power supply
used in MSA1500cs, MSA20, and EVA4x00/6x00/8x00 products.
NOTE:
Because this component is used in several products, the drawings
may re
fl
ect a different enclosure than the one you have. The
removal and replacement procedure is the same for each product.
Warranty information
If the product in which this part is being replaced is still under
HP warranty, then the replacement part(s) referred to in these
Replacement Instructions is provided under the terms and conditions
of the Hewlett-Packard Company Limited Warranty for that
product.
A copy of this Limited Warranty may be viewed at:
h
t
t
p
:
/
/
h
1
8
0
0
6
.
w
w
w
1
.
h
p
.
c
o
m
/
p
r
o
d
u
c
t
s
/
s
t
o
r
a
g
e
w
o
r
k
s
/
w
a
r
r
a
n
t
y
.
h
t
m
l
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under
HP's express limited warranty statement, which may be viewed at:
h
t
t
p
:
/
/
c
u
s
t
o
m
e
r
o
p
s
.
c
o
r
p
.
h
p
.
c
o
m
/
1
s
w
/
p
d
m
_
o
m
/
w
a
r
r
a
n
t
y
_
s
u
p
p
o
r
t
/
p
o
l
i
c
i
e
s
/
2
3
3
0
1
0
0
.
d
o
c
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The only warranty for this replacement product is as noted above.
Nothing in these replacement instructions should be construed as
constituting an additional warranty. The information provided in these
replacement instructions is provided "AS IS" and HP is not liable for
technical or editorial errors or omissions contained herein.
Before you begin
Observe the following precautions when replacing a power supply:
•
Removing a power supply signi
fi
cantly changes the air
fl
ow within
the enclosure. Both power supplies must be installed for the
enclosure to cool properly. If a power supply fails, leave it in place
in the enclosure until a new power supply is available to install.
•
If cabling is obstructing access to the power supply, carefully move
the cables out of the way to avoid loosening any connections.
•
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection.
•
Have a copy of the product user guide available for reference. You
can download a copy of the user guide from the product support
page on the HP website.
Verifying component failure
Before replacing a power supply, use the following methods to verify
the component failure.
Page 1