HP C8000 Mid-Weight Slide Kit (5069-6371) Installation Instructions
HP C8000 - Workstation - 0 MB RAM Manual
View all HP C8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP C8000 manual content summary:
- HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 1
shall not be liable for technical or editorial errors or omissions contained herein. Part Number 416755-003 March 2008 (Third Edition) About this device The HP Mid-Weight Slide Kit (5069-6371) enables you to install HP 2U, 3U, 4U, and 5U servers into HP round-hole, square-hole, threaded-hole, and - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 2
for installation: • T-25 Torx driver • Phillips screwdriver • Flathead screwdriver Using the marked mid-weight slide-mounting alignment tool, mark the front and rear columns of the rack. Item Description 1 Mark for HP 5U servers 2 Mark for HP 4U servers 3 Mark for HP 2U and HP 3U servers - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 3
-mounting alignment tool ("Marking your rack columns using the midweight slide-mounting alignment tool" on page 1). 5. Proceed to "Sliding the server into the mid-weight outer slide assemblies (on page 2)." Installing the mid-weight slides in early HP racks 1. Install the mid-weight inner slides - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 4
of the front brackets with the markings on the front of the rack columns. Secure the front brackets to the rack using M5 x 16-mm screws (2). 2. Connect the cables to the server. 5. Transfer the markings from the front of the rack columns to the sides of the rack columns, and install the - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 5
4. Extending the cable management arm, slide the server forward. (Optional) Adjusting the mid-weight outer slide assemblies NOTE: These steps apply only if the adjustment of the outer slide assemblies are necessary to - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 6
mm screws, secure the mid-weight inner slides to an HP 2U server. c. Using two M4 x 8-mm screws, secure the mid-weight inner slides to an HP 4U server. d. Using four M4 x 8-mm screws, secure the mid-weight inner slides to an HP 5U server. b. Using two M4 x 8-mm screws, secure the mid-weight inner - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 7
3. Using the marked mid-weight slide-mounting alignment tool, mark the front assemblies to secure it to the rack. Item Description 1 Mark for HP 5U servers 2 Mark for HP 4U servers 3 Mark for HP 2U and HP 3U servers 4. Remove the top pin from the mid-weight outer slide assemblies. WARNING - HP C8000 | Mid-Weight Slide Kit (5069-6371) Installation Instructions - Page 8
, to secure the cables. 11. Extending the cable management arm, slide the server forward. NOTE: The yellow plastic shipping tie is not included in the kit arm. NOTE: All M5 screws must be torqued to 6.2 Nm (55 lb). 15. Use the M5 x 16-mm screws to install and secure the tie-down bracket to the
HP Mid-Weight Slide Kit
(5069-6371)
Installation Instructions
About this device
The HP Mid-Weight Slide Kit (5069-6371) enables you to install HP
2U, 3U, 4U, and 5U servers into HP round-hole, square-hole,
threaded-hole, and early HP racks.
Kit contents
If any of the following items are missing or damaged, contact your
HP authorized reseller. The following hardware pieces are included
in this kit.
Quantity
Description
Picture
1
Cable management arm (J1539-63003)
2
Mid-weight inner slides (J1539-63001)
2
Mid-weight outer slide assemblies (J1539-
63002)
2
Hook-and-loop straps (1400-2030)
1
Mid-weight slide-mounting alignment tool
(5185-6098)
Hardware kit contents
Quantity
Description
Picture
2
M5 x 30-mm screw (0515-2992)
1
M5 x 10-mm screw (5021-2991)
2
M5 x 16-mm screw (0515-3019)
4
M4 x 8-mm screw (0515-2478)
2
M5 barrel nut (5065-7210)
1
Tie-down bracket (5069-6357)
Optional hardware kit contents (J1539-63004)
The optional hardware kit is required to install the mid-weight slide
kit into early HP racks.
Quantity
Description
Picture
4
M5 x 16-mm screw (0515-3019)
2
M6 flathead screw (5185-6036)
2
Front bracket (5184-2312)
© Copyright 2006, 2008 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The
only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing
herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Part Number 416755-003
March 2008 (Third Edition)