HP Color LaserJet Enterprise flow MFP M880 Hole Punch Kit Installation Guide
HP Color LaserJet Enterprise flow MFP M880 Manual
 |
View all HP Color LaserJet Enterprise flow MFP M880 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Color LaserJet Enterprise flow MFP M880 manual content summary:
- HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 1
AZW84-67902 2/3 Hole Punch Kit CZ999-67902 2/4 Hole Punch Kit ZZZKSFRPVXSSRUWFRORUOM0 ZZZKSFRPVXSSRUWFRORUOMƮRZ0)30 /HDHVWRSULPHUR www.hp.com/support/colorljM855 www.hp.com/support/colorljflowMFPM880 Lea esto primero CAUTION: Exposed sheet metal can have sharp edges. Be - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 2
3 4 Before proceeding, take note of the two locator pins on the back side of each cover. These pins must be correctly installed to assure proper alignment of the covers when they are reinstalled. Remove the covers (callout 1) by moving the top of the cover outward to release the positioning - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 3
9 10 Slightly lift up on the cover to release it, and then remove the cover. 11 Remove one screw from the punch rear cover assembly. 12 Slightly lift up on the cover to release it, and then remove the cover. 13 Open the punch door. 14 Pull the punch waste box straight out of the punch - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 4
15 16 Remove one screw. 17 Close the punch door, and then remove two screws. 18 Remove the cover. 19 Close the punch upper cover. 20 Remove one screw. Remove two screws. 4 - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 5
on the controller PCA, and then release the wire harnesses from one retainer (callout 2). Remove two screws. TIP: These screws fasten the rear sheet-metal support bracket to the punch assembly. Use the hole provided in the chassis next to the punch controller PCA to gain access to these screws. 25 - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 6
assembly is still fastened to the accessory chassis, but you should be able to disengage the support bracket. Remove one screw. 29 30 Remove one screw. 31 ZZZKSFRPVXSSRUW . NOTE: See the special installation instructions section on the following pages after installing the replacement assembly. - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 7
Special installation instructions 1 2 5HDUVLGH Reconnect the finishing accessory to the pages to assure alignment remains constant. NOTE: If some pages have skewed holes while others do not, the problem is a skew in the paper and not the punch. 7 )URQWVLGH Correct punch hole alignment. NOTE - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 8
5 Set the punch hole assembly type. Two types of punch hole assemblies are available: the 2/3 6 punch hole assembly (part number A2W94-67901), or the 2/4 punch hole assembly (part number CZ999-67902). Refer to the part number on the replacement part to determine the type of assembly you are - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 9
10 LED601 LED602 Blinking one time Blinking two times Blinking three times Blinking four times Not lit Blinking steadily LED blinking pattern explanation Not applicable 2/3 punch hole assembly selected 2/4 punch hole assembly selected Waiting for type setting completion Type setting - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 10
13 Set the sensor adjustment values. Follow the steps below to adjust the sensors on the punch controller PCA. 14 15 2 1 34 5 Make sure that the product power is off. 16 ON 1234 Set SW601 to the settings above. Locate the switches and LEDs on the punch controller PCA. • SW601 (callout 1) • - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 11
18 LED601 LED602 Solidly lit Blinking steadily Blinking alternately Not lit Blinking steadily LED blinking pattern explanation Adjusting sensors Waiting for adjustment completion Sensor adjustment completed 19 Follow these steps to adjust the sensors on the punch controller PCA. a. Press - HP Color LaserJet Enterprise flow MFP M880 | Hole Punch Kit Installation Guide - Page 12
© Copyright 2015 HP Development Company, L.P. A2W84-91001 A2W84-91001 $: 12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
AZW84-67902 2/3 Hole Punch Kit
CZ999-67902 2/4 Hole Punch Kit
$±:²³´µ¶·¸±
&=···´µ¶·¸±
¹
ZZZºKSºFRP»VXSSRUW»FRORUOM0²¼¼
ZZZºKSºFRP»VXSSRUW»FRORUOMƮRZ0)30²²¸
/HD HVWR SULPHUR
±
1
1
2
Turn the product off, and then disconnect the finishing accessory
from the product.
On the finishing accessory, remove four screws from the latch
lower covers.
NOTE
: The booklet maker with hole punch accessory is shown
in these photos, however the procedure is correct for all of the
finishing accessories.
CAUTION
: Exposed sheet metal can have sharp
edges. Be careful when working around
exposed sheet metal.
Lea esto primero
www.hp.com/support/colorljM855
www.hp.com/support/colorljflowMFPM880