HP D2D130 HP StorageWorks D2D Backup System Instructions for Installing Disks
HP D2D130 Manual
 |
View all HP D2D130 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP D2D130 manual content summary:
- HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 1
HP StorageWorks D2D Backup System Instructions for installing disks in a replacement HP D2D Backup System Part number: EH923-90902, Rev B Revised second edition: September 2007 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 2
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP registered trademark of Advanced Micro Devices, Inc. Printed in Hungary HP StorageWorks D2D Backup System - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 3
the tape drive and HBA from the failed unit, if one is installed • Install the hard disks in the replacement HP D2D Backup System. The disks may be installed in any order. • Install the HBA and tape drive in the replacement HP D2D Backup System, if one is required HP StorageWorks D2D Backup System 3 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 4
Always place drives with the Printed Circuit Board (PCB) assembly-side down. • Use conductive field service tools WARNING! Hazardous voltages are present inside the HP D2D Backup System. Always disconnect AC power from the server and other associated assemblies while working inside the unit. Serious - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 5
cables from the HP D2D Backup System. 3. Remove the access panel on the failed HP D2D Backup System. 1. Loosen the captive thumbscrew located on the rear edge of the access panel. 2. Slide the panel back about 2.5 cm (1.0 in). Figure 1 Removing the access panel HP StorageWorks D2D Backup System 5 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 6
can remove the hard disk drives. 1. Remove the screw. 2. Pull the cover up and away from the drives. Figure 3 Removing the drive cover 6 Installing a replacement HP D2D Backup System - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 7
. Lift the release tab on the drive latch. 3. Slide the hard drive out from the front of the drive bay. Figure 4 Removing the hard drive HP StorageWorks D2D Backup System 7 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 8
an external model, you have already disconnected the cables before removing the access panel. 2. Internal tape drives must be removed from the HP D2D Backup System. 1. Release the catch on the device bay and slide the tape drive out. 2. Disconnect the cables. Figure 5 Removing an internal tape drive - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 9
2. Remove the slot cover retainer. Figure 6 Removing the slot cover retainer 4. Remove the HBA from the top PCI slot. Figure 7 Removing the HBA HP StorageWorks D2D Backup System 9 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 10
Installing the hard disks in the replacement unit 1. Remove the access cover, front bezel and drive cover from the replacement unit, as described in steps 2 to 4 of "Removing the hard disks and tape drive from the failed unit" on page 5. 2. Observing normal anti-static precautions, install the disks - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 11
next drive up, HDD2, is connected to SATA2, and so on. Figure 9 Aligning the SATA cables Power Supply System Board HDD 4 HDD 3 HDD 2 HDD 1 SATA3 SATA4 SATA2 SATA1 3. When you have installed all four go to "Replacing the bezel and access panel" on page 16. HP StorageWorks D2D Backup System 11 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 12
external tape drive. It is always installed in the top PCI slot. 1. Undo the retaining screw on the PCI slot cover retainer on the replacement HP D2D Backup System. 2. Remove the slot cover retainer. Figure 11 Removing the slot cover retainer 12 Installing a replacement - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 13
cover next to the slot in which you are installing the HBA. 3. Install the HBA in the top PCI slot. Figure 13 Installing the HBA HP StorageWorks D2D Backup System 13 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 14
internal tape drive, re-install it now. 1. Access the removable media cage. 2. Remove the filler panel. Figure 15 Removing the filler panel 14 Installing a replacement HP D2D Backup System - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 15
you have installed an internal tape drive, remove the blank plate (1) at the top of the bezel. Figure 17 Removing plate for internal drive (optional) HP StorageWorks D2D Backup System 15 - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 16
it into place. 3. Tighten the captive thumbscrew to secure the access panel. Figure 19 Replacing the access panel (no tape drive installed) 16 Installing a replacement HP D2D Backup System - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 17
the HP D2D Backup System and use the iSCSI initiator to reconnect to it and make it a Logon target. Information on using the iSCSI initiator can be found in the HP StorageWorks D2D Backup System User Guide (if you are running on a Windows systems) and the Linux Configuration Guide. HP StorageWorks - HP D2D130 | HP StorageWorks D2D Backup System Instructions for Installing Disks - Page 18
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
HP StorageWorks
D2D Backup System
Instructions for installing disks in a replacement
HP D2D Backup System
Part number: EH923-90902, Rev B
Revised second edition: September 2007