HP D2D4004i HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo
HP D2D4004i Manual
View all HP D2D4004i manuals
Add to My Manuals
Save this manual to your list of manuals |
HP D2D4004i manual content summary:
- HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 1
Instructions Abstract This document explains how to install the HP StoreOnce 4210, 4220/4420 and 4430 Upgrade Kits, apply the new licenses, and add the new storage to the existing system. It is intended for system administrators familiar with the HP StoreOnce Backup systems. *BB864-90901* HP - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 3
the HP StoreOnce Backup System 7 HP StoreOnce 4220/4210 Backup Systems 7 HP StoreOnce 4430/4420 Backup Systems 8 3 Applying the License and Completing the RAID Expansion 10 Applying the License...10 Completing the RAID Expansion 11 Using the Hardware Tree to Monitor Progress 12 Troubleshooting - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 4
is for use with the HP StoreOnce 4210 Backup system. NOTE: For HP StoreOnce 4210 Backup systems, the configured available disk capacity of the With the HP 4430/4420 Backup system, it could be longer depending upon the shelf configuration and the amount of data. Make sure that host users are aware - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 5
• Prepare for expansion • Add storage to the HP StoreOnce Backup system IMPORTANT: When connecting multiple upgrade kits to an HP StoreOnce 4430/4420 Backup system, you must add all licenses before expanding the capacity of the HP StoreOnce Backup system. The storage expansion process will fail if - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 6
be installed directly below or above the HP StoreOnce Backup system. The HP 2U Rack Rail Kit installation instructions (shipped with the rail kit) information. WARNING! Ensure that sufficient personnel are on hand to support the product(s) during the installation process. Use of the appropriate - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 7
engage the device chassis to secure the rear of the chassis to the rails. Connecting the Upgrade Kit to the HP StoreOnce Backup System HP StoreOnce 4220/4210 Backup Systems 1. To ensure correct keying, first connect the supplied cable to the P1 connector on the top I/O module (I/O-A) on the rear - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 8
end of each cable to the connector on the RAID card. HP StoreOnce 4430 Backup system WARNING! Daisy-chaining Upgrade Kits is not supported. Each Upgrade Kit must be directly connected to one of the RAID cards on the HP StoreOnce Backup system. Each kit is supplied with two cables; the longer cable - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 9
not matter which connectors are used, but only three expansion shelves may be connected. Figure 5 Cabling the Upgrade Kit to the HP StoreOnce 4420 Backup system 1. Power connectors 3. Power on/off button 2. P1 connector (on I/O-A) 4. Port connector on RAID card 3. Use the supplied power cords to - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 10
on the internet) using any configured IP address for the appliance and provide an Administrator user name: ssh @ At the next prompt, enter the Administrator's password. IMPORTANT: When connecting multiple upgrade kits to an HP StoreOnce 4430/4420 Backup system, you must add all - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 11
you used email or a temporary file, cut and paste the string exactly as you obtained it from the HP Licensing website. Entering the LTU manually is not advised. 4. The key is specific to the HP StoreOnce Backup system to which it applies. It cannot be transferred. Completing the RAID Expansion NOTE - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 12
following command: hardware show storage status (or its alias, system show status) This command will return either of the following and from a CLI command. The tree is updated every five minutes, so changes to configuration such as the attachment of a new enclosure will take up to five minutes to - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 13
show problems command to list any enclosures with unconfigured storage. You can also use the hardware show storage status command for a textural view of the storage configured. See the HP StoreOnce Backup System CLI Reference Guide for more information on using these CLI commands. Troubleshooting - HP D2D4004i | HP StoreOnce 2600, 4200 and 4400 Backup system Capacity Upgrade Bo - Page 14
The hardware add storage command will fail if: • There is an outstanding prepare or add command in progress. • Any of the error conditions described above for the hardware prepare storage command have not been rectified. 14 Applying the License and Completing the RAID Expansion
HP StoreOnce 4210, 4220/4420 and
4430 Upgrade Kit
Installation Instructions
Abstract
This document explains how to install the HP StoreOnce 4210, 4220/4420 and 4430 Upgrade Kits, apply the new licenses,
and add the new storage to the existing system. It is intended for system administrators familiar with the HP StoreOnce Backup
systems.
*BB864-90901*
HP Part Number: BB864-90901
Published: October 2012
Edition: 1