HP Dc5800 Computer Setup (F10) Utility Guide
HP Dc5800 - Compaq Business Desktop Manual
 |
UPC - 883585860944
View all HP Dc5800 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Dc5800 manual content summary:
- HP Dc5800 | Computer Setup (F10) Utility Guide - Page 1
Computer Setup (F10) Utility Guide - dc5800 Models HP Compaq Business PCs - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 2
by copyright. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company. Computer Setup (F10) Utility Guide HP Compaq Business PCs First Edition (January 2008) Document Part Number: 460194-001 - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 3
About This Book This guide provides instructions on how to use Computer Setup. This tool is used to reconfigure and modify computer default settings when new hardware is installed and for maintenance purposes. WARNING! Text set off in this manner indicates that failure to follow directions could - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 4
iv About This Book ENWW - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 5
Table of contents Computer Setup (F10) Utility Computer Setup (F10) Utilities ...1 Using Computer Setup (F10) Utilities 2 Computer Setup-File ...3 Computer Setup-Storage 4 Computer Setup-Security 6 Computer Setup-Power ...9 Computer Setup-Advanced 10 Recovering the Configuration Settings 12 - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 6
vi ENWW - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 7
. ● Enter the Asset Tag or property identification number assigned by the company to this computer. ● Enable the power-on password prompt during system restarts (warm boots) as well as during power-on. ● Establish a setup password that controls access to Computer Setup (F10) Utility and the settings - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 8
and Exit. ● To reset to factory settings or previously saved default settings (some models), select Apply Defaults and Exit. This option will restore the original factory system defaults. CAUTION: Do NOT turn the computer power OFF while the BIOS is saving the Computer Setup (F10) changes because - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 9
core processors have this listed twice) ● Installed memory size/speed, number of channels (single or dual) (if applicable) ● Integrated MAC address for embedded, enabled NIC (if applicable) ● System BIOS settings and clears any established passwords. Ignore Changes and Exit Exits Computer Setup - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 10
Setup-Storage NOTE: Support for specific Computer Setup options may vary depending on the hardware configuration. Table 3 Computer Setup-Storage Option Description Device Configuration Lists all installed BIOS-controlled storage devices. When a device is selected, detailed information and - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 11
Removable Media Write, the computer will restart. Turn the computer off, then on, manually. DPS Self-Test Allows device other than the default device specified in Boot Order, restart the computer and press F9 when the monitor light turns green. After POST is completed, a list of bootable devices - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 12
the cover has been removed. Setup Password requires that the setup password be entered to boot the computer if the sensor detects that the cover has been removed. Device Security This feature is supported on some models only. See the Desktop Management Guide for more information. Allows you to - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 13
power-on password authentication scheme that utilizes the Embedded Security Device. Changing this setting requires turning the computer off and then back on. ● Reset authentication credentials (some models) (Do not reset/Reset) Selecting Reset disables the power-on authentication support and clears - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 14
requires turning the computer off and then back on. NOTE: To enable this option, a Setup password must be set. Smart Card BIOS Password Support (some models) (enable/disable) Allows the user to enable/ disable the Smart Card to be used in place of the Setup and Power-On Passwords. This setting - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 15
: If this feature is disabled, S4 and S5 both have the LED off. S1 (no longer supported) and S3 use 1 blink per second. SATA power management enables or disables SATA bus and/or device power management. Fan idle mode-This bar graph controls the minimum permitted fan speed. NOTE: This setting only - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 16
BIOS and launch HP Backup and supported on some models only.) ● Remote wakeup boot source (remote server/local hard drive). ● After Power Loss (off/on/previous state): Setting this option to: ◦ Off-causes the computer to remain powered off when power is restored. ◦ On-causes the computer to power - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 17
Value to 3. Restricts the number of CPUID functions reported by the microprocessor. Enable this feature if booting to Windows NT. Execute Memory Test Restarts the computer and executes the POST memory test. (some models) BIOS Power-On Allows you to set the computer to turn on automatically at - HP Dc5800 | Computer Setup (F10) Utility Guide - Page 18
be used to disable multi-processor support under the OS. ● Internal speaker (some models) (does not affect external speakers) ● Monitor Tracking (enable/disable). Allows BIOS to save monitor asset information. ● NIC PXE Option ROM Download (enable/disable). The BIOS contains an embedded NIC option
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
 |
 |
Computer Setup (F10) Utility Guide - dc5800
Models
HP Compaq Business PCs