Home » HP Manuals » Desktops » HP Dc7700 » Manual Viewer

HP Dc7700 ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business

HP Dc7700 - Compaq Business Desktop Manual

UPC - 882780715318

View all HP Dc7700 manuals

Add to My Manuals
Save this manual to your list of manuals

HP Dc7700 manual content summary:

HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 1
ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business Desktop Platforms Introduction 2 Supported features 2 Enablement and configuration 3 ASF 2.0 example and use case 6 Summary 7 1
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 2
document explores HP's support for industry-standard tools that enable the IT administrator to easily deploy ASF solutions within a Microsoft Windows environment. This white paper supports the following products: • HP Compaq dc5100 Business PC Series • HP dx5150 Series • HP Compaq dc5500 Business PC
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 3
the system to power up to S0 (system full powered) regardless of current system state. The power on command also supports boot options, allowing the management console to instruct the ASF client to boot off a specific device (hard drive, PXE, CD), as well as options to bypass the power-on password
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 4
HP Compaq dc7700 Business PC Series A Softpaq is available that contains the Intel HECI driver and the ASF Agent required to enable and configure ASF. You can find the agent in the \ASF 2.0 Tools\ASF Agent\ folder within the Softpaq. Full documentation is available in the \ASF 2.0 Tools\ASF Agent\
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 5
service this service is Management Console IP address, type the IP address of events. 7. HP recommends that control events. NOTE: HP does not recommend checking the ASF 1.0 Compatibility check box, as this option allows for Remote Control events with no authentication. 11. Type use a full 40-bit
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 6
prevented Windows from loading properly. 6. The Console then sends Client B an RMCP Power Reset command, hence Client B powers off and powers back on five seconds later. Client B now loads the operating system properly, and its console agent connects successfully and receives the software update
HP Dc7700 | ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business - Page 7
educate IT Administrators about the features supported by HP Compaq Business Desktops, and provide use cases regarding what makes this technology useful to manageability solutions. For more information, see the following links. References ASF 2.0 specification Broadcom's ASF page and white papers

Section	Page
ASF 2.0 Support, Enablement, and Configuration on HP Compaq Business Desktop Platforms	1
Introduction	2
Supported features	2
Alert-based events	2
Remote Management Control Protocol (RMCP) events	3
Enablement and configuration	3
1. You must enable ASF within the Intel Management Engine. If your system did not come with Intel AMT support, it should already...	4
2. Install the Intel HECI driver before installing the Intel ASF agent. You can find the driver in the same Softpaq at \\Drivers\\HECI\\.	4
Installing and Configuring the Intel ASF Agent:	4
1. Run the supplied setup.exe from the \\ASF 2.0 Tools\\ASF Agent\\ folder, and then follow the on- screen instructions.	4
2. After the installation is complete, launch Control Panel, and then double-click Intel(R) ASF Agent Console.	4
3. Select the General tab, and then click the check box at the top of the window to enable ASF.	4
4. From the Select active Adapter box, select Intel(R) 82566DM Gigabit Network Connection.	4
5. Enter the IP address of the SNMP console or Management Console to receive ASF traps.	4
6. Select the Security tab, click the Change button, and then enter the 40-bit hexadecimal keys that match your security settings. You cannot enable remote control events until completing this step.	4
7. Select the Remote Control tab, and then enable ASF remote control features as desired.	4
8. Reboot before using ASF features.	4
All products except for the HP Compaq dc7700 Business PC Series	4
Installing and Configuring the Broadcom ASF Agent:	5
1. Run the supplied setup.exe in the \\ASF\\Installer\\ folder, and then follow the on-screen directions. By default, the ASF Config and ASF IP Monitoring features are selected. These are the minimum recommended installations for ASF functionality.	5
2. After installation is complete, click Start > All Programs > Broadcom, and then click on the Broadcom ASF Configuration shortcut.	5
3. During the first installation, the applet alerts the user that the ASF Tables from the System ROM have been imported. Click OK.	5
4. Select the Settings tab, and then enable ASF by clicking the ASF Enabled check box.	5
5. In Management Console IP address, type the IP address of the SNMP or Management Console that is to receive ASF traps.	5
6. Click the Remote Management check box if you want to enable ASF Remote Management events.	5
7. HP recommends that you select the Wake on ARP or RMCP Traffic check box if the clients take advantage of Standby and Hibernate power management states. This option causes ASF management traffic to wake the system from low power states.	5
8. Select the Events tab, and then select the Transmit PET Messages check box if you want the client to send ASF traps to the SNMP or Management Console.	5
9. Select the Transmit System Heartbeat Messages check box if you want the client to send Heartbeats to the Management Console.	5
10. Select the Security tab, and then check the Secure Management check box to enable remote control events.	5
11. Type the desired 40-bit hexadecimal Generation Key.	5
12. The IT Administrator can define keys and rights for both Operator and Administrator roles/users. Type the desired 40-bit hexadecimal authentication key for each role, and check the rights that are desired for those roles.	5
13. Click OK after you complete the configuration.	5
14. Reboot the system before using ASF features.	5
ASF 2.0 example and use case	6
Example	6
1. The Console attempts to retrieve client status from ASF. The Console first authenticates both clients and establishes session IDs.	6
2. The Console then sends capability requests to the clients to determine remote capabilities. Both clients report back that they are capable of all RMCP events, and the Console populates remote control options for those clients for Administrator use.	6
3. The Console now needs to determine the state of the clients and sends System State requests. Both clients report back that they are currently in S4 (Hibernate).	6
4. The Console now knows it needs to wake the systems to update the software, so it sends RMCP Power Up commands to the clients, and both clients respond that they received the request (RMCP ACK).	6
5. At this point, the Console waits for the Console’s Agent Utility to report in and connect to the console for the software update.	6
6. The Console then sends Client B an RMCP Power Reset command, hence Client B powers off and powers back on five seconds later....	6
Summary	7
For more information, see the following links.	7

Match case Limit results 1 per page

ASF 2.0 Support, Enablement, and Configuration on HP

Compaq Business Desktop Platforms

Introduction

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Supported features

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Enablement and configuration

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

ASF 2.0 example and use case

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Summary

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7