HP Designjet 510 HP Designjet 510 Printer series - Setup Guide: English (US)
HP Designjet 510 Manual
View all HP Designjet 510 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Designjet 510 manual content summary:
- HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 1
Set-Up Printheads with Active Printheads 10. Load a Roll of Paper 11. Understand Printer Connections 12. Install and Connect a LAN Card 13. Using a USB Connection 14. Set Up Your Software The information on this poster applies to the following HP products: • HP Designjet 5XX Series • Stand and - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 2
use the poster supplied with it, open the box that contains the stand and the paper bin-it's the large box above the main printer body. 3-For models without a stand, go to Stage 6: Locate the Front-Panel Overlay and the Pocket Guide on page 4. 1-Attach the legs to the outside of the cross brace - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 3
Bin For assembly of the accessory stand, use the poster supplied with it 9-Remove the tapes from the spindle at the back of the printer. 1 2 x2 x2 3 4 5 6 6. Locate the Front-Panel Overlay and Pocket Guide (all models) NOTE: If your printer is an HP Designjet 510 you will not find the - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 4
printer and no light on the switch's LED, you have a power problem. printheads. 4-To remove a set-up printhead, lift up the blue handle. Note: HP Designjet 500 Mono has only one set-up printhead. 5-With controlled force pull the blue handle upwards until the printhead is released from the carriage - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 5
sheet paper, see the Pocket Guide for loading instructions.) 1-If your printer has legs, make sure the printer wheels are locked (the brake lever is pressed down) to prevent the printer from moving. 10-Close the window. After the replacement of the set-up printheads, the printer and stand the - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 6
models) If you have purchased a network card, for connecting your printer to a local area network (LAN), now is a good time to install it-see Stage 12. Also install now any HP-GL/2 Accessory card and any additional memory for your Accessory card. See the instructions packaged with these items for - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 7
root folder). 4. Follow the instructions to complete the software setup. Connected via the network Printer Your PC 1. Connect the printer to the network. 2. Make sure the printer is properly set up, turned on, and ready to print. 3. Insert the HP Designjet Printers 'Software Setup' CD and answer - HP Designjet 510 | HP Designjet 510 Printer series - Setup Guide: English (US) - Page 8
also get the software from HP's Web Site, the HP Download Service, Compuserve, or AOL. You can find out more from the driver software installation instructions, and from the description of supported installation methods on our Web site: http://www.hp.com/go/designjet For detailed information about
HP Designjet 5XX
series printers
Assembly and Set-Up Instructions
1. Check the Contents of the Package
This Assembly and
Set-Up
Poster
“Installation” package
containing cables,
printheads, ink
cartridges,
Pocket
Guide
.
[Packaging]
Main Printer
body
Check the items shown and notify your supplier if any are missing.
Don’t
open the items until you are prompted to do so on this
Poster
. The packaging varies between models; there may be additional items in the box.
[Packaging]
“Day-to-day”
package containing
Using Your Printer
documentation CD.
Box containing paper
bin and printer stand
(E+/A0+-size models
only)
Page 1
Contents of This Poster
1.
Check Contents of the Package
2.
Unpack the Main Components
3.
Assemble the Stand
4.
Attach the Stand to the Printer
5.
Assemble the Paper Bin
6.
Locate the Front-Panel Overlay and Pocket
Guide
7.
Switch On, Choose Language
8.
Insert Ink Cartridges
9.
Replace Set-Up Printheads with Active
Printheads
10. Load a Roll of Paper
11. Understand Printer Connections
12. Install and Connect a LAN Card
13. Using a USB Connection
14. Set Up Your Software
The information on this poster applies to the
following HP products:
• HP Designjet 5XX Series
• Stand and Paper Bin available as accessory.
If you are installing an
accessory
, such as a
stand, after the main installation has been
completed, use the instructions that came with
the accessory. If you are installing it at the
same time as the main installation, read the
appropriate stages of this
Poster.
For accessory cards, see “Understand Printer
Connections” and the documentation that
comes
with these accessories.
Read these instructions carefully...
and complete each stage before you start
the next.
What You Will Need to Do the Job
• Because some of the components of the
printer are bulky, you will need
2 or 3
people
to lift them. See the descriptions that
follow for details—a symbol like this is
used:
• You are recommended to have a floor area
of approximately
6 square metres
for
unpacking and assembling your printer.
• The time required to unpack, assemble and
set up the hardware is about
30 to 90
minutes,
depending on the model and
components (e.g. the stand).
The E+/A0+-size printer
with stand and paper
bin as standard.
The D/A1-size printer
with no stand or paper
bin as standard. If you have ordered a stand
and paper bin and are installing it now, follow
these instructions, as for a E+/A0+-size model.