HP Designjet L65500 HP Designjet L65500 Printer and HP Scitex LX Printer Famil
HP Designjet L65500 Manual
View all HP Designjet L65500 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Designjet L65500 manual content summary:
- HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 1
HP Designjet L65500 Printer & HP Scitex LX Printer family Installation guide (third edition) - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 2
are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Trademarks Microsoft® and Windows Vista® are - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 3
hazard ...2 Ink handling ...3 Warning and Cautions ...3 Warning labels ...3 Emergency stop buttons ...4 2 Introduction Installation guide overview ...6 Manpower required ...6 Tools required for installation ...6 Inbox content ...7 3 Receive the shipment Unload the crate ...9 Move the printer over - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 4
mains power ...31 Power on the printer ...32 7 Purge the ink system 8 Prepare the printer Install the printhead cleaning roll and aerosol Print the HP test images ...66 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) Appendix B Manually configure the printer's IP address - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 5
at hazardous voltages capable of causing death or serious personal injury. Turn off the printer using both Branch Circuit Breakers located in the building's Power Distribution Unit (PDU) before servicing the printer. The printer must be connected to earthed mains outlets only. To avoid the risk of - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 6
special care when accessing the substrate path. Fire hazard The drying and curing subsystems of the printer operate at high temperatures. Call your service representative if the printer's built-in Residual Current Circuit Breaker (Ground Fault Circuit Interrupter) is repeatedly tripped. To avoid the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 7
them. However, HP recommends that you wear gloves when handling ink cartridges or printhead cleaner rolls. Warning and Cautions The following symbols are used in this manual to ensure the proper use of the printer and to prevent the printer from being damaged. Follow the instructions marked with - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 8
enclosures of the printer's drying and curing modules. You are recommended to wear gloves when handling ink cartridges, printhead cleaning distributed around the printer. If an emergency occurs, simply push one of the emergency stop buttons to stop all printing processes. A system error message is - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 9
ENWW General safety guidelines 5 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 10
for the installation process. This guide is organized in chronological order and should be followed from beginning to end. Manpower required Installation of your HP Designjet L65500 & HP Scitex LX600/LX800 requires the following manpower: ● HP Installation Specialist ● Customer ● Certified - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 11
and troubleshooting guide ● Operating System Recovery CD ● Pneumatic gun ● L65500 only: 1 substrate roll ● 2 spindles (the front spindle is mounted on the printer with ties, the rear spindle is attached to the pallet) ● 1 empty substrate core ● L65500 only: ◦ HP 786 Yellow/Magenta Designjet - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 12
1 extra fuse ◦ Set of power jumpers includes 200V, 240/230V, 220V, 127V/120V and 115V/100V/110V ● Two electrical cabinet keys ● Printer Cleaning Kit ● Maintenance Kit ◦ 2 aerosol filters ◦ 1 printhead cleaner roll ● Purge kit ◦ 7 syringes and needles (extra syringe/needle set is included) ◦ 6 purge - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 13
weight distribution inside the crate. WARNING! Do not stand on top of the crate. Shown below are the recommended specifications of the forklift that should be used to move the crate. Forklift for L65500/LX600 Forklift for LX800 Weight 2721 kg (5999 lb) 3500 kg (7716 lb) Fork Length 2 m (78.74 in - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 14
Time 40 minutes NOTE: Approximately 16 bolts and 100 Phillips screws secure the crate. In some cases, it may be necessary to leave the printer inside the crate packaging to go up ramps or make second story deliveries. Plan accordingly. 1. Beginning with the top, left corners, remove the Phillips - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 15
support beams do not fall into the crate. 3. Use a Phillips screwdriver to remove the remaining screws that secure the side panels. 4. Carefully remove the panels and open the plastic bag surrounding the printer and free it from the printer. Remove the printer the Ink Collector Ink. 4. Use - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 16
up and the sliding door is secured with the tape used for transportation. 9. Locate the forklift guides underneath the printer and make sure that the forks on the forklift are spaced 80 cm apart (A). 10. Carefully lift the printer, move it away from the pallet and set it on the floor. NOTE: The - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 17
bars, spreader beam and any other crane attachment must be supplied by the customer. For the exact specifications of the crane attachments, see the Site Preparation Guide. WARNING! When lifting the printer with a crane, extra caution should be taken to ensure that the cables do not apply pressure to - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 18
14 Chapter 3 Receive the shipment ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 19
● Replace a substrate roll ● Service the printer or replace printer components ● Ensure the printer is well ventilated The printer has the following dimensions: Printer HP Designjet L65500 HP Designjet LX600 HP Designjet LX800 Length 5 m (16 ft, 5 inches) 5 m (16 ft, 5 inches 5.7 m (18 ft, 11 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 20
: 8m (26ft 3 in) B 1.5 m (5ft) C 0.6 m (2 ft) minimum D 4 m (13 ft, 2 in) E 1.5 m (5 ft) F 1.5 m (5 ft) WARNING! The zone surrounding the HP Designjet L65500 printer should be considered a restricted access area and signaled accordingly. Only trained personnel should be operating within - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 21
Tools Cutting Pliers, Allen keys, T20 and T25 screwdrivers Time 15 minutes 1. From the back, remove the electrical cabinet straps and foams from the printer. 2. Remove the straps from the sliding doors. NOTE: The keys to the electrical cabinet are located on top of the cabinet. ENWW Remove - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 22
extension for easier screw access. WARNING! Failure to remove the screws attaching the scan path assembly to the frame could seriously damage the printer. NOTE: The screws located at the back, are less accessible and may require a longer screwdriver. 4. Remove tape from the window and open the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 23
5. Remove the tie and 2 foam pieces that secure the service station. 6. Remove the four foam pieces that secure the top cover. 7. Remove the two T20 screws securing the printhead cleaning assembly. 8. Remove the substrate pressure - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 24
Remove the plastic tie securing the spindle and the tape covering the air valve. 11. Remove the ink system compartment strap from the printer. 12. Remove the plastic coverings from the ink cartridge connectors. 13. Remove the intermediate tank plastic bags, foams and straps. 14. Remove the plastic - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 25
16. Remove the tape covering the OMAS window on the print platen. 17. Remove the tapes covering the temperature sensors. 18. Remove the plastic covering from the carriage access door , front panel and central cover. 19. Remove tape from the Curing Plate. 20. Remove foam pieces from the left and - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 26
nut at the top of the foot. 2. Rotate the nut manually down the bolt. Leave about 0.8 inches (2 cm) of clearance at the bottom between nut and foot. ground, tighten the 30 mm locking nut against the printer structure NOTE: The right side of the printer is heavier than the left side. Therefore, the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 27
Cord The cable must meet the requirements of the printer and should be in accordance with the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. Printer's tri-phase line specifications High-voltage systems Input voltage (line to line) 3 x 380 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 28
Tri-phase Power Cord attachment 1. The Tri-phase AC power cord must be attached to the back of the Main Switch. 2. Back of the Main Switch is shown below: This Main Switch is made by two blocks of identical size, each one having three contacts. The left block is dedicated to tri-phase lines, so the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 29
The AC power cords (tri-phase and single-phase) have to be screwed to the bottom terminals of the switch. Add adequate ferrules on power cord cable terminations. In total there are 6 terminals to attach wires, and only 5 of them are to be used. They are labeled (from left to right): L1, L2, L3, ( - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 30
Protective Earth conductors (grounding) The printer must be connected to a good quality, dedicated ground line in order to avoid electrical risk. Please note your obligation to comply with the Electrical Code requirements of the local jurisdiction of the country where the equipment is installed. - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 31
the electrical system Install the fuses and power jumper Manpower 1 person Time 5 minutes NOTE: The electrical system inside the printer must be configured by the service engineer during installation. CAUTION: If there are any doubts regarding the proper installation of the fuse or power jumper - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 32
Printer Sites with high voltage supply (200- Sites with low voltage supply (100- 290V) 120) HP Designjet L65500/LX600 20 A 32 A HP Designjet LX800 25 A 1 Japan minutes There are two Delta/Star terminal blocks located on the printer that must be configured. Use the following table to make - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 33
CAUTION: Both Delta/Star terminal blocks must use the same configuration. Delta configuration1 Star configuration2 1 Use the delta configuration for tri-phase power supply voltages from 200-220 V (between phases). 2 Use the star configuration for tri-phase power supply voltages from 380-415 V ( - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 34
Curing Module Configuration 1. Remove all the T10 screws securing the right cover of the curing module and remove the cover. TIP: The heating module cover you must remove is marked with orange tape. 2. There is a strap that does not allow you to remove the terminal block. Remove this strap, taking - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 35
the heating and curing cables: 1, 2, 3). The acceptable values are as follows. ● L65500/LX 600 only: Triangle configuration (low input tri-phase, 200-220 V between phases left remote controller board (remove the left trim) ● The ink supply module board ● The capping station's remote controller board - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 36
by wiring them directly to the PDU, according to the National Electrotechnical Code (NEC). For more information about the HP Designjet L65500 electrical specifications, see the Site Preparation Guide. Power on the printer Manpower 1 person Time 5 minutes Ground check 1. Check that the Protective - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 37
cabinet. 4. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the input single-phase filter. ENWW Power on the printer 33 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 38
5. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the printer structure. 6. Check that the Protective Bonding Conductor (green-and-yellow grounding cable) is well attached to the drying system (at the resistor connection). 34 Chapter 6 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 39
Conductor (green-and-yellow grounding cable) is well attached to the curing system (at the resistor connection). Turn power on 1. Make sure that the printer is ready to be turned on. Make sure that the emergency stop buttons are not pressed. Make sure the ACB-1, ACB-2 and ACB-3 circuit breakers - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 40
will automatically start in diagnostic mode so you can purge the ink system. When you first turn on the printer, you must set the voltage according to the country of installation. Configure the voltage 1. From the front panel, enter the diagnostic menu and select Purge - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 41
not bent or damaged. The purge process requires at least 1.7 liters of ink per ink cartridge. Purge the ISM tubes NOTE: From the ink cartridge to the purging port, no air can be tolerated. From the purging port to the printhead, the printer can tolerate a cumulative total of 20 cm of air (the length - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 42
menu on the front panel, select Purge and Setup Menu > Purge ISM. 8. Select the color you want to purge. Ink Supply Legend ● 1=K ● 2=Y ● 3=C ● 4=M ● 5 = LM ● 6 = LC NOTE: The printer starts up the procedure, which may take a couple of minutes. TIP: Do not press the OK button more than once - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 43
before the electrovalve closes. NOTE: The printer will beep during these 200 seconds. 12. Check that all of the electrovalves have opened (you can hear a clicking sound). If not, perform the 4.6 ISS Electrovalves diagnostic procedure described in the Service Manual. While the test is in progress - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 44
purge port with a cloth around the needle to prevent spills. 16. Press OK on the front panel to close the electrovalves. 17. Check that the ink has arrived as far as the purging bag and purger. 18. Press OK to confirm that you have finished purging the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 45
OK to confirm that you have installed the ink cartridge. 22. The printer checks the pressure sensors. If the pressure is correct, press OK to continue. If the pressure sensor value is below the limits or is negative then follow the steps in Problems with the ink sensor value on page 42. 23. Enter - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 46
25. Remove the purger quick connector. Problems with the ink sensor value 1. There are three different cases that can cause a problem. ● The pressure sensor value is below a limit, which may vary depending on the volume of the supply. Probably there is an air bubble inside the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 47
● The pressure sensor gives a negative value. If the pressure is negative, there may be an error in the ink pressure PCA or in the ink pressure sensor cable. Check both by looking at the connection of the cable to the ISS PCA and at the pressure sensor PCA. Press OK - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 48
step 20 in the process of purging the ISM tubes. If the problem is not solved after trying this twice, perform the 4.5 ISS Ink Pressure Sensors diagnostic procedure found in the Service Manual. Fill the intermediate ink tanks 1. From the front panel, select Purge and Setup Menu > Fill intermediate - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 49
that they are installed from the front panel. The printer unfolds the intermediate ink tanks. This process takes approximately 25 minutes. NOTE: During this time, you can install the printhead cleaner roll, aerosol filters, HP Internal Print Server and switch. See Install the printhead cleaning - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 50
internal fittings of the connectors or result in an incorrect color matching of the ink tubes. 7. Test the connection by gently pulling both connectors away from each other . At this point, the printer sends ink to the carriage. This process takes approximately 5 minutes. 46 Chapter 7 Purge the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 51
purgers. Look at the air purgers and confirm that each color arrived to the air purger. 11. If ink did not reach one of the air purgers, use a syringe to complete the operation. For instructions, see Use a syringe to purge the tubes from the ISM to the printheads on page 48. 12 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 52
during start up, follow the troubleshooting instructions in the Service Manual. 18. When the printer finishes initializing, select the preferred before you insert it into the ink port. 4. Enter the service menu and select Purge and Setup Menu > Purge Printer Tubes to perform the purge again. - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 53
NOTE: If the syringe plunger does not move at all, pull it out no more than 1 mm. Otherwise, never manually pull the syringe plunger out. 6. When the purge operation is finished, put a cloth around the needle and remove the syringe quickly. NOTE: Wait until the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 54
the printhead cleaning roll, open the door on the front right of the printer. 2. Grip the handle and pull the whole printhead cleaning roll assembly material according to the instructions provided with the new roll. Keep the empty core to use as a takeup core. 4. Slide the new roll onto the upper - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 55
about clearing a printhead cleaning roll jam. Pull the whole assembly out, wind a little of the roll forward, then slide it back in again. The printer will check the roll again 9. Restore the pinch system by moving the black knob back into place. If you feel resistance because the cleaning roll - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 56
Open the printhead access door in the side of the printer, and lift the carriage cover. 2. The aerosol filter the bottom of its container and dispose of it according to the instructions provided with the new filter. 5. Unpack the new filters and ensure that the blue tabs at each end of each - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 57
the OK key on the front panel. 10. When you finish the purging process and are ready to start the printer, select Check cleaner roll from the Ink System menu in normal printer mode. Install the computer, monitor, LAN switch, tray, keyboard and mouse Manpower 1 person Tools T20, T30 Phillips - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 58
will damage the cables. Cables wrongly positioned: hanging over the sliding door support Cables correctly positioned: supported above the sliding door support 3. Use a T20 screwdriver to remove the monitor holder on the printer. 4. Remove the Phillips screws that secure the monitor arm and remove - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 59
the contents of the shared folder. 1. Log in to the HP Internal Print Server computer using the administrative user account that is already set up on the computer. ● HP Designjet L65500: User name hp65500, no password. ● HP Designjet LX800/LX600: User name scitexlx, no password. 2. Create a folder - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 60
3. Open the folder properties for the new OutJobs folder and navigate to the Sharing tab. 4. Click on Advanced Sharing to set the sharing properties. 5. Make sure that Share this folder is selected. 56 Chapter 8 Prepare the printer ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 61
> Network and Sharing Center on Windows Vista, and make sure that File Sharing is turned on. Configure the printer's IP address NOTE: If you cannot establish a connection between the printer and Internal Print Server, make sure that no proxy is configured. See Configure the proxy on page 74 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 62
2. Set the printer IP address in the Internal Print Server, under Tools > Preferences. 3. Configure HP Proactive Support and make sure the customer accepts all disclaimers, under Tools -> Proactive support 58 Chapter 8 Prepare the printer ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 63
and also follow the instructions on the front panel. 1. At the front panel, select the Ink System icon and then Replace printheads. 2. When requested by the front panel, open the printhead access door in the side of the printer. 3. Lift the carriage cover. 4. Check that the new printhead is of - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 64
servicing. 6. Shake the printhead according to the instructions on the packaging. 7. Put the new printhead into its correct place in the printer recommendations. 1. Use the procedures in the Service Manual, described under "Large ink area missing or substantial horizontal banding". 2. Request - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 65
of the printhead. Callme@HP Setup Process During installation process, specific information must be introduced into the IPS preferences to correctly route the Remote Support Calls to the Support Agent (HP or Authorized Service Provider approved to provide this Remote Support Service). 1. Go to the - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 66
supporting this printer, using the reseller's domain used for creating the account. ● If the reseller is not entitled to use the "Callme@hp" remote troubleshooting tool, then leave the default value: [email protected] 3. Launch the "callme@HP the User's Guide. 62 Chapter 9 Prepare for printing ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 67
customer's RIP for use with the HP Designjet L65500 Printer The customer's RIP must be configured correctly to work with the HP Designjet L65500 Printer. Because HP cannot support the customer's RIP, any troubleshooting must be done using the documentation and service that accompany the RIP. However - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 68
Port' should automatically be displayed. If not launch the RIP-Queue and select 'Configure the Printer'. The following screen is displayed, select 'Print to HP Internal Printer Server' and click on the 'Configure' button. 2. The following screen is displayed. Enter or browse to the Internal Print - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 69
RIP is sold with the HP Scitex LX800/LX600 Printer. After the RIP software has been installed and the printer has been added to the 'Connection' tab, the following screen is displayed. Enter the IP address of the printer (not the IP address of the IPS). Install the covers Manpower 1 person Tools - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 70
with which you can check the print quality achieved once the printer has been fully installed. From HP's Web site (http://www.hp.com/), select Support & drivers, check Download software & drivers, type the name of the printer, select Drivers, and download the pre-ripped images. 66 Chapter 9 Prepare - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 71
the error can come only from the printer's installation HP IPS\Test Plot\Ripped SAV Gloss Make sure before printing the files that the printer is ready to print at its best. 1. Load the roll of substrate provided with the printer. 2. Align the printheads (see the Maintenance and Troubleshooting Guide - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 72
5. Perform Dynamic Color Calibration, mainly when using the HP Photorealistic substrate. A specific user's guide for this calibration is available from http://www.hp.com/. 6. Print the three ripped files provided, using the Internal Print Server. Nest them to print all on the same row. We recommend - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 73
45 minutes The following procedure must only be performed in Japan and Russia. 1. Power up the HP Internal Print Server computer. 2. Choose the language for Windows Vista. TIP: Remember that the HP Internal Print Server software will automatically be installed in the language you choose for Windows - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 74
3. Click on Update my score. Change the power settings 1. Select Control Panel > Hardware and Sound > Power Options. 70 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 75
2. Select High performance and click on Change plan settings. 3. In the Put the computer to sleep field, select Never. ENWW 71 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 76
>Disk drives > HDD >Properties > Policies (tab). 2. Check the following: ● Optimize for performance ● Enable write caching on the disk ● Enable advanced performance 72 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 77
Enable scheduled defragmentation 1. Select Start > Computer > (Right click) Manage > Disk Management >(Right click) C: > Properties > Tools. ENWW 73 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 78
● Smooth edges of screen fonts ● Use visual styles on windows and buttons Configure the proxy 1. Log in with the HPL65500 account. 74 Appendix A Prepare the HP Internal Print Server (Japan and Russia only) ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 79
. Install the HP Internal Print Server TIP: If necessary, the HP Internal Print Sever executable file can be found on the web at http://www.hp.com under the Support & Drivers tab. 1. Find the setup.exe icon on the desktop, double click on the icon and follow the on-screen instructions. ENWW 75 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 80
the Internal Print Server, navigate to Tools > Preferences and set the printer IP address in the Internal Print Server. 3. From the Internal Print Server, navigate to Tools > Proactive support. Configure the HP Proactive Support and make sure the customer accepts all disclaimers. 4. Configure Call - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 81
not able to automatically retrieve an IP address. In this case, you must manually configure the IP address. Use the following procedure to manually configure the IP address for the printer. 1. Select the setup menu icon . 2. Select Connectivity. 3. Select Gigabit Ethernet. 4. Select View Information - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 82
5. Select TCP/IP. 6. Select IPV4 Settings. 7. Select Config Method. 8. Select Manual to change the configuration so the printer uses the manual settings. 9. From the IPV4 Settings menu, select Manual Settings. 78 Appendix B Manually configure the printer's IP address ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 83
10. Select IP Address to edit the settings. 11. Edit the IP address settings and press OK when you are finished. ENWW 79 - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 84
C Change the Windows Vista language 1. Navigate to the Control Panel on the Internal Print Server and select Clock, Language, and Region. 80 Appendix C Change the Windows Vista language ENWW - HP Designjet L65500 | HP Designjet L65500 Printer and HP Scitex LX Printer Famil - Page 85
2. Select the appropriate entry from the format list. ENWW 81
HP Designjet L65500 Printer & HP Scitex
LX Printer family
Installation guide (third edition)