HP Designjet L65500 HP 104-in Dual Roll Kit - User's guide
HP Designjet L65500 Manual
 |
View all HP Designjet L65500 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Designjet L65500 manual content summary:
- HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 1
HP 104-in Dual Roll Kit User's guide - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 2
The only warranties for HP Products and services are set forth in the express warranty statement accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 3
of contents 1 Introduction ...1 Purpose ...1 Main components ...1 Requirements ...1 2 Use of the dual-roll spindle ...2 Load rolls onto the spindle ...2 Load rolls into the printer ...5 3 Troubleshooting ...10 4 Specifications ...11 Appendix A Changes to roll loading and unloading 12 ENWW iii - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 4
iv ENWW - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 5
Dual Roll Kit with an HP Designjet L65500 printer, you must check that the printer's firmware and HP Internal Print Server software are up to date. Go to http://www.hp.com/ and click Support & Drivers > Download drivers and software (and firmware), enter the product name L65500, click the name of - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 6
Dual-roll spindle 2 Use of the dual-roll spindle Load rolls onto the spindle The dual-roll spindle is marked to assist you in positioning the differential hub. Loading the dual-roll spindles 1. Ensure that the differential hubs on the input and output spindles are aligned with each other. 2 - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 7
Dual-roll spindle 2. When both differential hubs are correctly positioned, use an Allen key 6 to tighten the screws and secure them in place. If a differential hub is loose, the substrate could become skewed during printing. TIP: You should tighten the screw until the washer touches the bolt. If - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 8
Dual-roll spindle 5. Insert the first roll on the spindle. 6. Replace the hub, and secure it with the Allen key. 7. Insert the second roll on the spindle. 8. Replace the hub, and secure it with the Allen key. 9. Ensure that the end of the right-hand roll is located within the maximum allowed - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 9
rear dual-roll spindle and two empty cores loaded on the front dual-roll spindle. See Load rolls onto the spindle on page 2. 1. Tell the printer that you are going to begin loading for dual-roll printing. 2. Remove the substrate edge holders in the print platen, or move them aside, so - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 10
output spindles while loading. Dual-roll spindle 6. Bring the new rolls on their spindle to the rear of the printer, with the geared end of the spindle on the longer roll should be on the right as seen from the front of the printer; on the left as seen from the rear. NOTE: When the shorter roll - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 11
Dual-roll spindle 9. Open the latches at both ends of the spindle (if they were closed) and push the roll on its spindle into the printer. 10. Close the latches to secure the spindle in place. TIP: If you cannot close the gear side latch, try sliding the spindle towards the - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 12
15. Once in front of the printer, if you find that you haven't unrolled enough substrate, select Start main roller motion from the front panel's Substrate menu to unroll some more. The - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 13
may wrinkle in the print zone, to avoid ink smearing. Be aware that raising the printhead from by the printer in this way. In such cases, you will be asked to enter the required information manually. Use the -hand edge that must be entered manually. 22. In the HP Internal Print Server, choose from the - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 14
to the spindle. Lack of tension can also occur when successive layers of substrate stick to each other on the roll. If you experience ink smears on the substrate after a period of dual-roll printing, try removing the central edge holders. Troubleshooting 10 Chapter 3 Troubleshooting ENWW - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 15
4 Specifications Minimum roll width Maximum roll width Minimum gap between rolls Maximum roll diameter Maximum total weight of both rolls 914 mm (36 in) 1245 mm (49 in) 152 mm (6 in) 250 mm (9.84 in) 100 kg (220 lb) Specifications ENWW 11 - HP Designjet L65500 | HP 104-in Dual Roll Kit - User's guide - Page 16
and unloading After installing the new firmware and software, you must go to the HP Internal Print Server and select Substrate > Load/Unload in order to load or unload substrate, instead of using the front panel as before. When loading substrate, you will see a Printer Configuration window in which
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
 |
 |
HP 104-in Dual Roll Kit
User’s guide