HP Deskjet 320 User Guide - Page 42

Contact HP, Solution, I connected the USB cable, but I am having problems using the HP All-in-One

Get HP Deskjet 320 PDF manuals and user guides View all HP Deskjet 320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

www.hp.com/support If prompted, choose your country/region, and then click Contact HP for information on calling for technical support. I connected the USB cable, but I am having problems using the HP All-in-One with my computer Solution You must first install the software that came with the HP All-in-One before connecting the USB cable. During installation, do not plug in the USB cable until prompted by the onscreen instructions. Connecting the USB cable before prompted can cause errors. Once you have installed the software, connecting your computer to the HP All-inOne with a USB cable is straightforward. Simply plug one end of the USB cable into the back of your computer and the other into the back of the HP All-in-One. You can connect to any USB port on the back of your computer. Troubleshooting For more information on installing the software and connecting the USB cable, see the Setup Guide that came with the HP All-in-One. The HP All-in-One does not print Solution ● Look at the On light located on the front of the HP All-in-One. If it is not lit, the HP All-in-One is turned off. Make sure the power cord is firmly connected to the HP All-in-One and plugged into a power outlet. Press the On button to turn on the HP All-in-One. ● Make sure the print cartridges are installed. ● Make sure you have paper loaded in the input tray. ● Check that the HP All-in-One does not have a paper jam. ● Check that the print carriage is not jammed. User Guide 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
www.hp.com/support
If prompted, choose your country/region, and then click
Contact HP
for
information on calling for technical support.
I connected the USB cable, but I am having problems using the HP All-in-One
with my computer
Solution
You must first install the software that came with the HP All-in-One
before connecting the USB cable. During installation, do not plug in the USB
cable until prompted by the onscreen instructions. Connecting the USB cable
before prompted can cause errors.
Once you have installed the software, connecting your computer to the HP All-in-
One with a USB cable is straightforward. Simply plug one end of the USB cable
into the back of your computer and the other into the back of the HP All-in-One.
You can connect to any USB port on the back of your computer.
For more information on installing the software and connecting the USB cable,
see the Setup Guide that came with the HP All-in-One.
The HP All-in-One does not print
Solution
●
Look at the
On
light located on the front of the HP All-in-One. If it is not lit,
the HP All-in-One is turned off. Make sure the power cord is firmly connected
to the HP All-in-One and plugged into a power outlet. Press the
On
button to
turn on the HP All-in-One.
●
Make sure the print cartridges are installed.
●
Make sure you have paper loaded in the input tray.
●
Check that the HP All-in-One does not have a paper jam.
●
Check that the print carriage is not jammed.
User Guide
39
Troubleshooting