HP EVA4000/6000/8000 HP StorageWorks controller enclosure cache battery replac
HP EVA4000/6000/8000 Manual
 |
View all HP EVA4000/6000/8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP EVA4000/6000/8000 manual content summary:
- HP EVA4000/6000/8000 | HP StorageWorks controller enclosure cache battery replac - Page 1
StorageWorks controller enclosure cache battery replacement instructions About this document This document provides the procedure for replacing a controller cache battery in EVA4x00/6x00/8x00 products, with the exception of the EVA4400. For the latest documentation, go to http://www.hp.com/support - HP EVA4000/6000/8000 | HP StorageWorks controller enclosure cache battery replac - Page 2
. This is the indication you typically see after installing a new battery. Battery fault. The battery has failed and should be replaced. The battery has experienced an over temperature fault. Battery code is being updated. When a new battery is installed, it may be necessary for the controllers to - HP EVA4000/6000/8000 | HP StorageWorks controller enclosure cache battery replac - Page 3
by pressing it firmly into place. • From HP Command View EVA: • Navigate to the component and check the status. It should be (Good). • Turn off the locate function by clicking Locate > Locate Off. Figure 3 Removing a cache battery Installing a battery Position the battery as high in the slot as
-
1 -
2 -
3
 |
 |
HP StorageWorks
controller enclosure cache
battery replacement instructions
These instructions apply to the EVA4000, 4100,
6000, 6100, 6400, 8000, 8100, and 8400
products.
© Copyright 2009 Hewlett-Packard Development Company, L.P.
Sixth edition: March 2009
The information in this document is subject to change without
notice.
Printed in Puerto Rico
www.hp.com
*531236-001*
About this document
This document provides the procedure for replacing a controller
cache battery in EVA4x00/6x00/8x00 products, with the
exception of the EVA4400. For the latest documentation, go to
h
t
t
p
:
/
/
w
w
w
.
h
p
.
c
o
m
/
s
u
p
p
o
r
t
/
m
a
n
u
a
l
s
, and select your product.
The information contained herein is subject to change without notice.
The only warranties for HP products and services are set forth in the
express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional
warranty. HP shall not be liable for technical or editorial errors or
omissions contained herein.
WARRANTY STATEMENT: To obtain a copy of the warranty for this
product, see the warranty information website:
h
t
t
p
:
/
/
w
w
w
.
h
p
.
c
o
m
/
g
o
/
s
t
o
r
a
g
e
w
a
r
r
a
n
t
y
Before you begin
Observe the following precautions when replacing a cache battery.
CAUTION:
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection.
NOTE:
The quantity of installed cache batteries varies with EVA models.
Two battery slots are located at the left front of the controller
enclosure. Two additional battery slots are located behind the
operator control panel (OCP).
Verifying component failure
Use the following methods to verify component failure:
CAUTION:
If HP Command View EVA does not present a status consistent with
the battery status indicator, or if either HP Command View EVA or
your system monitoring tool indicates multiple hardware failures,
contact HP support for assistance (
h
t
t
p
:
/
/
w
w
w
.
h
p
.
c
o
m
/
s
u
p
p
o
r
t
).
•
Analyze any failure messages received. Fault monitoring software
from HP (WEBES) provides a recommended solution.
•
Check status using HP Command View EVA:
1.
In the navigation pane, select
Storage system > Hardware >
Rack > Controller Enclosure > Controller
.
NOTE:
The EVA6400/8400 does not have a Rack selection in
the navigation pane.
2.
In the Content pane, select the
Enclosure
tab. The status is
displayed in the
Cache Battery Modules
fi
eld. The status should
be
(Failed).
Page 1