HP EVA4000/6000/8000 HP StorageWorks Power Supply Replacement Instructions (56
HP EVA4000/6000/8000 Manual
View all HP EVA4000/6000/8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP EVA4000/6000/8000 manual content summary:
- HP EVA4000/6000/8000 | HP StorageWorks Power Supply Replacement Instructions (56 - Page 1
HP StorageWorks Power Supply Replacement Instructions These instructions apply to the MSA1500 cs, MSA20, and EVA 4000/6000/8000 products. The part may also be used in other HP products. Please refer to documentation for your specific product for detailed replacement instructions. Printed on at least - HP EVA4000/6000/8000 | HP StorageWorks Power Supply Replacement Instructions (56 - Page 2
respectively. Remember to make this conversion when replacing a power supply. This inconsistency is corrected in later versions of HP Command View EVA. 1. In the Navigation pane, select Storage system > Hardware > Rack > Controller enclosure > Controller 2. In the Content pane, select the Enclosure - HP EVA4000/6000/8000 | HP StorageWorks Power Supply Replacement Instructions (56 - Page 3
: 408 STORAGE BOX # POWER SUPPLY OK • On an EVA product, from Command View EVA • Navigate back to the component and check the status. It should be • Turn off the locate function by clicking Locate > Locate Off Returning the failed component Please follow the return instructions provided with
HP StorageWorks
Power Supply Replacement
Instructions
These instructions apply to the MSA1500 cs, MSA20,
and EVA 4000/6000/8000 products. The part may
also be used in other HP products. Please refer to
documentation for your speci
fi
c product for detailed
replacement instructions.
Printed on at least 50% total recycled
fi
ber with at least
10% post-consumer paper.
© Copyright 2005-2006 Hewlett-Packard Development Company,
L.P.
Second edition March 2006
Product names mentioned herein may be trademarks of their
respective companies as re
fl
ected by an associated footnote.
The information in this document is subject to change without
notice.
Printed in the U.S.A.
www.hp.com
.
*5697-5245*
Warranty Information
If the product in which this part is being replaced is still under
HP warranty, then the replacement part(s) referred to in these
Replacement Instructions is provided under the terms and conditions
of the Hewlett-Packard Company Limited Warranty for that
product.
A copy of this Limited Warranty may be viewed at:
h
t
t
p
:
/
/
h
1
8
0
0
6
.
w
w
w
1
.
h
p
.
c
o
m
/
p
r
o
d
u
c
t
s
/
s
t
o
r
a
g
e
w
o
r
k
s
/
w
a
r
r
a
n
t
y
.
h
t
m
l
If this is a trade sale part (product out of warranty), then the replacement
part(s) referred to in these Replacement Instructions is provided under
HP's express limited warranty statement, which may be viewed at:
h
t
t
p
:
/
/
c
u
s
t
o
m
e
r
o
p
s
.
c
o
r
p
.
h
p
.
c
o
m
/
1
s
w
/
p
d
m
_
o
m
/
w
a
r
r
a
n
t
y
_
s
u
p
p
o
r
t
/
p
o
l
i
c
i
e
s
/
2
3
3
0
1
0
0
.
d
o
c
The replacement part takes on either the Limited Warranty Period of the
part being replaced or a ninety-day period that begins upon installation
of the replacement part, whichever is greater.
The only warranty for this replacement product is as noted above.
Nothing in these replacement instructions should be construed as
constituting an additional warranty. The information provided in these
replacement instructions is provided "AS IS" and HP is not liable for
technical or editorial errors or omissions contained herein.
About This Document
This document describes the procedure for replacing the power
supply used in MSA 1500 cs and MSA20 products, and EVA
4000/6000/8000 products.
NOTE:
Because this component is used in several products, the
drawings may re
fl
ect a different enclosure than the one you
have. The removal and replacement procedure is the same
for each product.
Before you begin
Observe the following precautions when replacing a power supply.
CAUTION:
Removing a power supply signi
fi
cantly changes the air
fl
ow
within the enclosure. Both power supplies must be installed for
the enclosure to cool properly. If a power supply fails, leave it
in place in the enclosure until a new power supply is available
to install.
If cabling is obstructing access to the power supply, carefully
move the cables out of the way to avoid loosening any
connections.
Parts can be damaged by electrostatic discharge. Use proper
anti-static protection. Refer to the documentation that shipped
with your system for additional information.
Have a copy of the product User Guide available for reference.
You can download a copy of the User Guide from the product
support page on the HP web site.
Page 1