HP EVA4000/6000/8000 HP Replication Adapter for VMware vCenter Site Recovery M
HP EVA4000/6000/8000 Manual
View all HP EVA4000/6000/8000 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP EVA4000/6000/8000 manual content summary:
- HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 1
P9000 XP Storage Replication Manager Software for VMware vCenter SRM version 2.0 Administrative Guide Abstract This guide contains detailed instructions for installing, removing, configuring, and using the P9000 Virtualization Adapter. The intended audience has independent knowledge of related OS - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 2
contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 3
SRM...43 Migration to site B, due to a disaster at site A 43 Migration to site B, due to a planned or host down (ESX server) at site A 43 5 Troubleshooting RMSRA20 44 Known problems...44 Contents 3 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 4
Collecting the information...48 RMSRA20 local configuration 48 RMSRA20 remote configuration 49 6 Support and other resources 50 Related documentation...50 HP technical support...50 Subscription service...50 HP websites...50 Documentation feedback...51 Typographical conventions...51 Glossary...52 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 5
needed for scenarios like failovers and test failovers. SRM is a service on Windows that executes the script for the replicated LUNs discovery see the HP P9000 Raid Manager User Guide available at: http://h20000.www2.hp.com/bc/docs/support/SupportManual/c03017860/c03017860.pdf Prerequisites HP P9000 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 6
Display name Event Log VMware VirtualCenter Server VMware Site Recovery Manager Service Startup type Automatic Automatic Automatic • RMXP SRA and Array "Supported version of RMXP SRA and RAID Manager and microcode" (page 6) shows the support matrix of the RMXP SRA (rmsra command) and RAID Manager - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 7
Primary and secondary conceptual configurations for RMSRA20 Figure 1 (page 7) is a conceptual diagram that shows the SRM configuration used by the RAID Manager for implementing SRA2.0. Figure 1 Primary and seconday configurations for SRA 2.0 Coordination process of SRM and SRA 2.0 Discovery of - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 8
1. SRM makes a request to RM SRA to find available arrays. 2. RM SRA connects to a RAID Manager Instance and requests all groups to find array controller information (WWN) and, using RAID Manager commands, to find remote arrays. 3. RM SRA returns the results to SRM. Discovery Devices sequence The - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 9
device. 5. SRM follows the reverseReplication command with syncOnce and querySyncStatus commands to initiate and monitor data transfer. This is necessary when production services have been running at site B for long enough to create a large amount of data that must be replicated back to site A. NOTE - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 10
syncOnce and querySyncstatus commands The syncOnce and querySyncStatus command sequence is: 1. SRM makes a request to RM SRA with the syncOnce command to be synchronized and executes periodic querySyncStatus commands to check replication progress using syncID returned by syncOnce. Checking continues - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 11
Figure 3 (page 11) shows a local configuration using Virual Command Device (VCD). For more information on VCD, see the P9000 Raid Manager User Guide. Figure 3 RMSRA20 local configuration using VCD RMSRA20 is configured by SRA command.pl as interface adapter and RMSRA20 commands. In local connection - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 12
calls RMSRA20 commands on a remote RAID Manager, RMSRA20 is included with the HP P9000 Raid Manager installation. See the RAID Manager User Guide for supported systems. NOTE: Executing RMSRA20 over Telnet does not work if the RAID Manager instance in running on Windows, because Windows does not have - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 13
Figure 5 RMSRA20 configuration using RAID Manager on VM RM SRA is configured by SRA command.pl as an interface adapter and uses the RMSRA20 command. In case of a remote storage connection configuration, SRA command.pl calls the RMSRA20 command on a Guest OS running a RAID Manager instance. The Guest - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 14
Figure 6 RAID Manager configuration for RMSRA20 Fiber Address conversion table The VMware ESX Server uses WWN and LUN# notation for device discovery. The fiber conversion table number for HORCM should be changed by using the $HORCMFCTBL variable. For example: • C:\HORCM\etc> set HORCMFCTBL=3 • C:\ - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 15
Figure 7 RAID Manager configuration files example 1 For the instance number and target port in the example in Figure 8 (page 16): • X is the RAID Manager instance number • BC is not used for testFailover • CL4-G-1 is the target port for the ESX Server RMSRA20 configurations 15 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 16
Figure 8 RAID Manager configuration files example 2 NOTE: The conditions that testFailover (executed on CA/CAJ_SVOL) are: • BC licence is not installed (does not register as Group for BC ). • SRM or the $SplitReplication variable specifies = true. Or: • BC licence is installed. • - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 17
, make sure your SRM protection group lUNs match your CT group lUNs. CT groups cannot be used in a multiple array (MxN configuration). Starting HORCM service In Windows, the RAID Manager provides the svcexe.exe command and a sample script file (HORCM0_run.txt) so that the RAID Manager (HORCM) can be - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 18
HORCM_EVERYCLI environment variable. See the HP P9000 Raid Manager User Guide for details. Considering Parallel failover If you must execute Failover "Failover Action and Configurations" (page 18) shows the related support between the action of failover and applicable configurations. The SRM/SRA - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 19
Table 3 Failover Action and Configurations (continued) SRM component Component name Failover actions Failover testfailover Split = false Split = true +BC (at time split Unused. See Available ) Note 2 Available +CoW (at time Unused. See Available split ) See Note 3 Note 2 Available +BC/ - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 20
SRM. RAID700 or RAID600 F/W version 60-04-02 or later is supported at-time-split for CoW and is required. XP2000/24000 Firmware version 60-04-02 or later and P9500 supports at-time-split for CoW. Volumes using CoW w have the NO READ - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 21
Making standalone device/consistency groups SRM (AM) manages to do failover using the datastore standalone device. The consistency group for the datastore is generated automatically during the device information reported by RMSRA20. In Figure 11 (page 21) at the protection site, the consistency - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 22
Figure 13 Device Pair list SRM (AM) shows the relation between the Device_Name of the horcm.conf and the datastore name. 22 VMware Site Recovery Manager overview - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 23
site SRM server (recovery site). You must confirm that the VMware Site Recovery Manager Service is enabled as a service You must also confirm the services in Table 1 (page 6) by using Adminstrative Tool > Services as shown in Figure 14 (page 23). Figure 14 Display example To install the software - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 24
Service service is stopping. The VMware Site Recovery Manager Service service was stopped successfully. C:\>net START vmware-dr The VMware Site Recovery Manager Service service is starting. The VMware Site Recovery Manager Service service the number of arrays supported in a multi-array configuration - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 25
SRM server and the remote (recovery site) SRM server. You must confirm that the VMware Site Recovery Manager Service is enabled as a service You must also confirm the services in Table 1 (page 6) by using Adminstrative Tool > Services as shown in Figure 16 (page 26) Updating the software version 25 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 26
2. Delete the installed RM SRA with Addition and deletion of application on the control panel. 3. Execute rmhtcsra.exe. 4. Restart the VMware Site Recovery Manager Service by entering one of the following commands if vmware-dr will be started. C:\>net STOP vmware-dr The VMware Site Recovery Manager - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 27
the version Uninstallation procedure 1. Deletes the installed RM SRA with Addition and deletion of application on the control panel. 2. Restart VMware Site Recovery Manager Service by entering the following command if vmware-dr will be started. C:\>net STOP vmware-dr The VMware Site Recovery Manager - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 28
groups using RAID Manager. For more information on these tasks, see the RAID Manager, Basic Specifications R65 in the HP P9000 RAID Manager User Guide. When you put a virtual disk into a data replication group, it must replicate (paircreate ) to the remote HP array. At the remote data center, you - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 29
Configuring SRM (AM) to communicate with RMSRA20 Adding Array Manager 1. Configure the Array Manager on protection. When the protected and recovery SRM servers have been paired, click add an Array Manager to configure the Array Manager to use RMSRA20 (see Figure 18 (page 29)). Figure 18 Configure - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 30
Figure 19 Add Array Manager 3. For an RMSRA20 configuration using remote connection, enter HORCM instance and IP Address to connect to the RAID Manager instance via RMSRA20, specifying the following formats (see Figure 20 (page 31)). 30 Configuring SRM and P9000 (XP) disk array - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 31
Figure 20 HORCM remote connection instance Configuring SRM (AM) to communicate with RMSRA20 31 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 32
• To connect to the RAID Manager on a remote UNIX Host, enter one of the following: ◦ HORCMINST=X@Host-name, which connects to HORCMINST=X on the Remote UNIX Host. ◦ $HORCMINST@Host-name, which connects the $HORCMINST setting to the Remote Login Environment on a UNIX Host. NOTE: If the array is set - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 33
Figure 21 HORCM local connection instance • To connect to the RAID Manager on the current Windows system, enter one of the following: ◦ HORCMINST=X, which connects to HORCMINST=X on the current Windows host. ◦ $HORCMINST, which connects to %HORCMINST% set to the current Windows host. 5. Enter the - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 34
Figure 22 Protected site array manager adapter information 7. To configure the Array Manager on recovery, when the protected and recovery SRM servers have been paired, click add an Array Manager to configure Array Manager to use RMSRA20. 34 Configuring SRM and P9000 (XP) disk array - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 35
Figure 23 Configuring Array Manager on recovery Configuring SRM (AM) to communicate with RMSRA20 35 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 36
8. To add RMSRA20 to the recovery side Array Manager, define an appropriate name as Display Name and Select RAID Manager Storage Replication Adapter from an SRA Type that is connected to RMSRA20. Figure 24 Add RMSRA20 to recovery side • For an RMSRA20 configuration using remote connection, enter the - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 37
Figure 25 Configure the virtualization adapter with a remote Telnet connection ◦ To connect to the RAID Manager on a remote UNIX host enter one of the following commands: - HORCMINST=X@Host-name, which connects to HORCMINST=X on the remote UNIX host. - $HORCMINST@Host-name, which connects the $ - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 38
• For an RMSRA20 configuration using local connection, enter the HORCM instance to connect to the RAID Manager instance via RMSRA20, specifying the following formats: Figure 26 Configure the virtualization adapter for local configuration ◦ Enter HORCMINST=X to connect to HORCMINST=X on the Windows - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 39
Figure 27 Array Manager summary screen Verifying Array Manager on protection Verify that the Local Array ID and Remote Array ID are discovered by the protection array manager (see Figure 28 (page 40)). Configuring SRM (AM) to communicate with RMSRA20 39 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 40
Figure 28 Array Pairs tab Enabling devices and verifying datastores Verify that the local and remote devices have been discovered by the protection array manger: • The local device name and remote device name are the dev_name on horcm*.conf. • The direction is rightness. • The datastore is mapped to - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 41
Figure 29 Protected devices screen Verifying the devices and replicated datastore on recovery Verify that the local and remote devices have been discovered with the following information by the recovery array manger: • The local device name and remote device name are the dev_name on horcm*.conf. • - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 42
to the recovery site during test and recovery. For more information on creating protection groups, see the VMware Site Recovery Manager Administration Guide. Create recovery plans Create recovery plans on the recovery site. A recovery plan is a list of steps the SRM follows on a protected site - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 43
failback with SRM and provides a scenario as a guide for the manual failback process. Failover Failover occurs when an SRM normal server migration process. In the following failback scenario, SRM supports a manual failback operation by executing reprotect and failover operations. Migration to - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 44
5 Troubleshooting RMSRA20 Known problems The following problems and solutions are typical: HP disk arrays do not appear in Site Recovery Manager Solution: If the specified connection address. Action: Confirm that the User/Password for the connection address is appropriate. 44 Troubleshooting RMSRA20 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 45
]: [command_naming] : Unsupported command 'command naming' in XML. Cause: A command name was input from SRM to the SRA, but it could not be supported. Action: Confirm that SRM was passed an appropriate command name in XML from the SRM log message. 1251 : [RMSRA20][Time]: [command_main] : Can't be - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 46
try to run the same command manually using the RAID Manager CLI. Confirm Manager stand alone, then see the RAID Manager User Guide to fix the error. COMMAND ERROR : EUserId for Confirm that the RAID Manager is the corrected version supported RM SRA. 1256 : 1257 : 1260 [RMSRA20 Troubleshooting RMSRA20 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 47
with checktestfailover/testfailover. Action: Confirm that the RAID Manager corrected version is supported in RM SRA. Error codes for multiple errors RM SRA defines an error See the RAID Manager command error code in the RAID Manager User Guide. The volume is in the incorrect state (SMPL) for this - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 48
parameter for a command in XML. NO array ID or device key parameter for a command in XML. NOT supported command name in XML. Open error for the specified file in XML. Unexpected RM command error. Collecting the RAID Manager command error log by entering the following: 48 Troubleshooting RMSRA20 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 49
%ALLUSERSPROFILE%\VMware\VMware vCenter Site Recovery Manager\Logs\vmware*.log • Collect the outputs of the following command on HORCMINST=XX (instance# for SRA): set %HORCMROOT%\HORCM\etc\raidqry -l %HORCMROOT%\HORCM\etc\raidqry -g %HORCMROOT%\HORCM\etc\pairdisplay -IH -g ??? -CLI -l -fwe port - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 50
website: http://www.hp.com/support/manuals Below Storage, click Storage Software. The following book is available on the VMware website: • VMware Site Recovery Manager Administration Guide HP technical support For worldwide technical support information, see the HP support website: http://www.hp.com - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 51
bodily harm or death. CAUTION: Indicates that failure to follow directions could result in damage to equipment or data. IMPORTANT: Provides clarifying information or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. Documentation feedback 51 - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 52
This glossary defines acronyms and terms used in this guide or related to this product and is not a are defined from RAID0 to RAID6. HP StorageWorks Disk Arrays in the XP product family support RAID1, RAID5 and RAID6. The datacenter containing the virtual machines that are recovered and perform - HP EVA4000/6000/8000 | HP Replication Adapter for VMware vCenter Site Recovery M - Page 53
, 44 G glossary, 52 H help obtaining, 50 HP technical support, 50 P prerequisites, 5 R related documentation, 50 S Site Recovery Manager Overview, 5 Subscriber's Choice, HP, 50 T technical support HP, 50 service locator website, 50 troubleshooting, 44 W websites, 50 HP , 50 HP Subscriber's Choice
P9000 XP Storage Replication Manager
Software for VMware vCenter SRM version
2.0 Administrative Guide
Abstract
This guide contains detailed instructions for installing, removing, configuring, and using the P9000 Virtualization Adapter. The
intended audience has independent knowledge of related OS software and of HP disk arrays and software.
HP Part Number: 5697-2491
Published: January 2013
Edition: Sixth