HP EVA6400 HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013)
HP EVA6400 Manual
View all HP EVA6400 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP EVA6400 manual content summary:
- HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 1
HP P6000 Enterprise Virtual Array Release Notes XCS 11001100 Abstract This document applies to the HP EVA4400/6400/8400, HP P6300/6500 EVA, and HP P6350/6550 EVA storage systems. HP Part Number: 5697-2516 Published: March 2013 Edition: 4 - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 2
© Copyright 2013 Hewlett-Packard Development Company, L.P. Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 3
HP Command View EVA product page (http:// h18006.www1.hp.com/products/storage/software/cmdvieweva/index.html) for more information. • XCS 11001100 requires iSCSI or iSCSI/FCoE module firmware 3.2.2.7 or later. To download the firmware, go to Software Depot >HP Storage> Storage Software >HP P6000 EVA - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 4
manual intervention to address. • Addressed an issue for the use of the VAAI XCOPY feature with LUNs that are greater than 2 TB in size. • Addressed a USTL/CSM reset termination, which occurs when the XCS controller HP P6000 Command View to access an unused code development device causes the array - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 5
fails during removal of a virtual disk from a DR group. • Fixed issue in which controllers encounter a recursive termination (TEC: 0x06710101) after back end SAS port reset. • Fixed issue caused by updating disk drive firmware on a storage system with an unsupported version of HP P6000 Command View - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 6
the LUNs to the application's host or affecting changes to the SAN configuration. HP P6000 Command View display • Fixed issue that prevented accurate display of a failed host port status in EVA P6000 Command View. Disks (disk groups, virtual disks) This section describes issues affecting physical - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 7
instructions, see the HP Enterprise Virtual Array Updating Product Software Guide (XCS 11001100). You can download these documents from the following website: http://www.hp.com/support/manuals Under Storage, click Disk Storage Systems, and then under EVA P6000 Storage, select your storage system. HP - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 8
with HP P6000 Command View 9.2 or later pre-installed on the management module within the controller enclosure (for array-based management). • The HP P6300/6500 EVA are shipped with HP P6000 Command View 9.4 or later pre-installed. • The HP P6350/6550 EVA are shipped with HP P6000 Command View 10 - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 9
down the array, perform the following steps: 1. Use HP P6000 Command View to shut down the controllers and disk enclosures. 2. Turn off power from the rack power distribution unit (PDU). 3. Turn on power from the rack PDU. After startup of the management module, the controllers will automatically - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 10
to verify the correct firmware version is displaying. 3. If the problem persists, contact HP Support Engineering. Disk group occupancy set the protocol to HP FC Data Replication Protocol in HP P6000 Command View as follows: 1. Select the upgraded array in the EVA Storage Network Properties window. - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 11
methods to upgrade the firmware to ensure a successful upgrade, or your array code load will fail in a VMware Guest OS configuration: • Array-Based Management module • Physical server-based HP P6000 Command View • Direct Path I/O mapping from ESX (requires supported hardware on the ESX server - HP EVA6400 | HP P6000 EVA Release Notes (XCS 11001100) (5697-2516, March 2013) - Page 12
HP P6000 Command View on a Windows 2003 or 2008 management server, HP MPIO P6000 DSM 4.02.00 and DSM Manager are installed automatically. You can download the latest DSM Manager and HP MPIO P6000 DSM from the following HP website: http://www.hp.com/support/downloads 1. Under Storage, select Storage
HP P6000 Enterprise Virtual Array Release
Notes
XCS 11001100
Abstract
This document applies to the HP EVA4400/6400/8400, HP P6300/6500 EVA, and HP P6350/6550 EVA storage systems.
HP Part Number: 5697-2516
Published: March 2013
Edition: 4