HP Healthcare Edition HC271 Product Notice AMS

Regulatory Notice

HC271/HC271p Clinical Review Monitors

HP Inc.,1501 Page Mill Road,

Palo Alto, CA 94304, United States

WARNING!

Electricity.

CAUTION:

Indicates a hazardous situation that, if

not avoided, could result in damage to equipment

or loss of information.

Consult instructions for use.

Alternating current

Indications for use/

intended use

• This display is intended for healthcare

professionals viewing patient information,

records, medical examination images, or results

in a hospital or clinical medical environment.

• This display is not intended for use in

interpreting or analyzing patient information,

records, medical examination images, or

results. The display is intended only to provide

information to assist healthcare professionals in

making an independent diagnosis or treatment

decision regarding an individual patient.

• Do not operate this display with any surgical,

life-support, or radiological equipment

(mammography equipment included).

• Do not use this display with radiology,

pathology, or mammography systems for

patient diagnosis purposes.

Connecting to external

devices

All the equipment intended to connect

this display shall be certified according to

international standards IEC60601-1, IEC60950

or other IEC/ISO Standards applicable to the

equipment.

All configurations of equipment must comply

with the system standard IEC60601-1.

Connecting any additional equipment to the

signal input port or signal output port of this

display is considered configuring a medical

system. Therefore, the system must comply

with the requirements of the system standard

IEC60601-1.

Disconnecting devices

A power cord is included with the display. If

another cord is used, use only a power source

and connection appropriate for this display. For

information on the correct power cord set to

use with the display, refer to the

Product Notices

provided in your documentation kit.

WARNING!

To reduce the risk of electric shock or

damage to the equipment:

• Plug the power cord into an AC outlet that is easily

accessible at all times.

• Disconnect power from the computer by unplugging

the power cord from the AC outlet.

• If provided with a 3-pin attachment plug on the power

cord, plug the cord into a grounded (earthed) 3-pin

outlet. Do not disable the power cord grounding

pin, for example, by attaching a 2-pin adapter. The

grounding pin is an important safety feature.

• Installations must be set up by qualified personnel

only.

• It is the responsibility of the operating institution

to choose qualified personnel for installation and

operation of the device.

Cleaning the display

1. Turn off the display.

2. Disconnect any external devices.

3. Wipe the exterior with a soft, water-

dampened cloth to remove any visible soiling.

4. Next, use any of the following germicidal

wipe formulations to safely disinfect all

exposed surfaces of your monitor. Refer

to the directions for use provided by the

manufacturer of the wipes.

CAUTION:

The cloth should be moist, but not wet.

Water dripping into the ventilation or other points

of entry can cause damage to the monitor. Allow the

unit to air-dry before use.

Regulatory Notice

HC271/HC271p Clinical Review Monitors

HP Inc.,1501 Page Mill Road,

Palo Alto, CA 94304, United States

WARNING!

Electricity.

CAUTION:

Indicates a hazardous situation that, if

not avoided, could result in damage to equipment

or loss of information.

Consult instructions for use.

Alternating current

Indications for use/

intended use

• This display is intended for healthcare

professionals viewing patient information,

records, medical examination images, or results

in a hospital or clinical medical environment.

• This display is not intended for use in

interpreting or analyzing patient information,

records, medical examination images, or

results. The display is intended only to provide

information to assist healthcare professionals in

making an independent diagnosis or treatment

decision regarding an individual patient.

• Do not operate this display with any surgical,

life-support, or radiological equipment

(mammography equipment included).

• Do not use this display with radiology,

pathology, or mammography systems for

patient diagnosis purposes.

Connecting to external

devices

All the equipment intended to connect

this display shall be certified according to

international standards IEC60601-1, IEC60950

or other IEC/ISO Standards applicable to the

equipment.

All configurations of equipment must comply

with the system standard IEC60601-1.

Connecting any additional equipment to the

signal input port or signal output port of this

display is considered configuring a medical

system. Therefore, the system must comply

with the requirements of the system standard

IEC60601-1.

Disconnecting devices

A power cord is included with the display. If

another cord is used, use only a power source

and connection appropriate for this display. For

information on the correct power cord set to

use with the display, refer to the

Product Notices

provided in your documentation kit.

WARNING!

To reduce the risk of electric shock or

damage to the equipment:

• Plug the power cord into an AC outlet that is easily

accessible at all times.

• Disconnect power from the computer by unplugging

the power cord from the AC outlet.

• If provided with a 3-pin attachment plug on the power

cord, plug the cord into a grounded (earthed) 3-pin

outlet. Do not disable the power cord grounding

pin, for example, by attaching a 2-pin adapter. The

grounding pin is an important safety feature.

• Installations must be set up by qualified personnel

only.

• It is the responsibility of the operating institution

to choose qualified personnel for installation and

operation of the device.

Cleaning the display

1. Turn off the display.

2. Disconnect any external devices.

3. Wipe the exterior with a soft, water-

dampened cloth to remove any visible soiling.

4. Next, use any of the following germicidal

wipe formulations to safely disinfect all

exposed surfaces of your monitor. Refer

to the directions for use provided by the

manufacturer of the wipes.

CAUTION:

The cloth should be moist, but not wet.

Water dripping into the ventilation or other points

of entry can cause damage to the monitor. Allow the

unit to air-dry before use.

PRINTER: Replace this box with Printed- In (PI) Statement(s) as per spec.

NOTE: This box is simply a placeholder. PI Statement(s) do not have to fit

inside the box but should be placed in this area.

*L39819-DN2*

L39819-DN2

Technical specifications

All specifications represent the typical

specifications provided by HP’s component

manufacturers; actual performance may vary either

higher or lower.

For the latest specifications or additional

specifications on this product, go to http://www.

hp.com/go/quickspecs/ and search for your

specific display model to find the model-specific

QuickSpecs.

Display

68.6 cm (27.0 in) wide screen

Type

AHVA

Viewable image size

68.6 cm (27.0 in) diagonal

Weight (Net)

HC271: 5.0 kg (11.0 lbs)

HC271p: 5.15 kg (11.4 lbs)

Weight with stand*

HC271: 7.16 kg (15.8 lbs)

HC271p: 7.31 kg (16.1 lbs)

*

(Optional) HP Stand Kit, product number 4BX37AA,

Weight: 2160 g, Dimensions: 210 x 196.9 x 434.8 mm

(W x H x D)

Dimensions

Height

Display head only: 39.25 cm (15.45 in)

With stand: 55.79 cm (21.96 in)

Depth



Width

Display head only:

64.41 cm (25.36 in)


Maximum graphic resolution

2560 x 1440 (60 Hz)

Optimum graphic resolution

2560 x 1440 (60 Hz)

Dot pitch

0.233 (H) x 0.233 (V) mm

Pixels per inch

109 PPI

Horizontal frequency

30 kHz to 90 kHz

Vertical refresh rate

50 Hz to 60 Hz

Environmental requirements

Temperature

Operating 5°C to 35°C (41°F to 95°F)

Storage/transportation

-20°C to 60°C (-3.99°F to 140°F)

Humidity

Operating: 20%-80%

Storage/transportation: 5% to 95% RH at 38.7°C

Altitude

Operating 0 m to 2,000 m (0 to 6,562 ft)

Storage/transportation: 0 m to 12,192 m (0 to

40,000 ft)

Atmospheric pressure range

Operating: 80 kPa to 101 kPa

Storage/transportation: 24.0 kPa to 101 kPa

Relative humidity

20% to 80%

Power source

100 V ac to 240 V ac 50/60 Hz

Measured power consumption

Full power: 55 W

Typical settings: 45 W

Sleep: <0.5 W

Off: <0.3 W

Input terminal

One DisplayPort port, one HDMI port, one VGA

port, one USB Type-B port (upstream), and two

USB 2.0 Type-A ports (downstream)

DICOM mode

HC271: available

HC271p: not available

IP Protection

IP32 on the front glass

Contacting HP

Go to www.hp.com/support to locate your

user guide, drivers, and software. For safety,

regulatory, and environmental information,

refer to the

Product Notices

provided with your

product.

© Copyright 2018 HP Development Company, L.P.

The information contained herein is subject to change without

notice. The only warranties for HP products and services are set

forth in the express warranty statements accompanying such

products and services. Nothing herein should be construed as

constituting an additional warranty. HP shall not be liable for

technical or editorial errors or omissions contained herein.

Second Edition: August 2018

First Edition: July 2018

Technical specifications

All specifications represent the typical

specifications provided by HP’s component

manufacturers; actual performance may vary either

higher or lower.

For the latest specifications or additional

specifications on this product, go to http://www.

hp.com/go/quickspecs/ and search for your

specific display model to find the model-specific

QuickSpecs.

Display

68.6 cm (27.0 in) wide screen

Type

AHVA

Viewable image size

68.6 cm (27.0 in) diagonal

Weight (Net)

HC271: 5.0 kg (11.0 lbs)

HC271p: 5.15 kg (11.4 lbs)

Weight with stand*

HC271: 7.16 kg (15.8 lbs)

HC271p: 7.31 kg (16.1 lbs)

*

(Optional) HP Stand Kit, product number 4BX37AA,

Weight: 2160 g, Dimensions: 210 x 196.9 x 434.8 mm

(W x H x D)

Dimensions

Height



Depth



Width

Display head only:

64.41 cm (25.36 in)


Maximum graphic resolution

2560 x 1440 (60 Hz)

Optimum graphic resolution

2560 x 1440 (60 Hz)

Dot pitch

0.233 (H) x 0.233 (V) mm

Pixels per inch

109 PPI

Horizontal frequency

30 kHz to 90 kHz

Vertical refresh rate

50 Hz to 60 Hz

Environmental requirements

Temperature

Operating 5°C to 35°C (41°F to 95°F)

Storage/transportation

-20°C to 60°C (-3.99°F to 140°F)

Humidity

Operating: 20%-80%

Storage/transportation: 5% to 95% RH at 38.7°C

Altitude

Operating 0 m to 2,000 m (0 to 6,562 ft)

Storage/transportation: 0 m to 12,192 m (0 to

40,000 ft)

Atmospheric pressure range

Operating: 80 kPa to 101 kPa

Storage/transportation: 24.0 kPa to 101 kPa

Relative humidity

20% to 80%

Power source

100 V ac to 240 V ac 50/60 Hz

Measured power consumption

Full power: 55 W

Typical settings: 45 W

Sleep: <0.5 W

Off: <0.3 W

Input terminal

One DisplayPort port, one HDMI port, one VGA

port, one USB Type-B port (upstream), and two

USB 2.0 Type-A ports (downstream)

DICOM mode

HC271: available

HC271p: not available

IP Protection

IP32 on the front glass

Contacting HP

Go to www.hp.com/support to locate your

user guide, drivers, and software. For safety,

regulatory, and environmental information,

refer to the

Product Notices

provided with your

product.

EMC Notice

Electromagnetic immunity

Immunity test

IEC 60601 Test levels

Compliance level

Electromagnetic environment–Guidance

Electrostatic discharge (ESD)

IEC 61000-4-2

±8 kV contact

±15 kV air

±8 kV contact

±15 kV air

Floors should be wood, concrete or ceramic tile. If floors are covered with

synthetic material, the relative humidity should be at least 30%.

Electrical fast transient/burst

IEC 61000-4-4

±2 kV for power supply lines ±1

kV for input/ output lines



The main power quality should be that of a typical commercial or hospital

environment

Surge

IEC 61000-4-5

±1 kV line(s) to line(s)

±2 kV line(s) to earth




environment.

Voltage dips, short interruptions

and voltage variations on power

supply input lines

IEC 61000-4-11

< 5%

U

T

1 (> 95% dip in

U

T

) for

0.5 cycle, 40%

U

T

(60% dip in

U

T

)

for 5 cycles, 70%

U

T

(30% dip in

U

T

) for 25 cycles, < 5%

U

T

(>95%

dip in

U

T

) for 5s

< 5%

U

T

(> 95% dip in

U

T

) for 0.5

cycle, 40%

U

T

(60% dip in

U

T

) for

5 cycles, 70%

U

T

(30% dip in

U

T

)

for 25 cycles, < 5%

U

T

(>95% dip

in

U

T

) for 5s


environment. If the user of the HC271/HC271p requires continued operation

during interruptions in the main power, it is recommended that the HC271/

HC271p be powered from an uninterruptible power supply or a battery.

Power frequency

(50 Hz) magnetic field

IEC 61000-4-8

30 A/m

30 A/m

Power frequency magnetic fields should be at least characteristic of a typical

location in a typical commercial or hospital environment.

Conducted RF induced by RF fields

IEC 61000-4-6

3 Vrms 150 kHz - 80 MHz 6Vrms

ISM and Amateur Radio Bands

3 Vrms 150 kHz - 80 MHz, 6Vrms


Portable and mobile RF communications equipment should be used no

closer to any part of the OEV262H, including cables, than the recommended

separation distance calculated from the equation appliance to the frequency

of the transmitter. Recommended separation distance: d = 1.2 √P, d = 1.2

√P 80 MHz to 800 MHz, d = 2.3 √P 800 MHz to 2.7 GHz, where P is the

maximum output power rating of the transmitter in watts (W) according to the

transmitter manufacturer and d is the recommended separation distance in

meters (m). Field strengths from fixed RF transmitters, as determined by an

electromagnetic site survey

a

, should be less than the compliance level in each

frequency range

b

. Interference may occur in the vicinity of equipment marked

with following symbol:

Radiated RF EM fields and

Proximity fields from RF wireless

communications equipment

IEC 61000-4-3

10 V/m, 80 MHz - 2,7 GHz,

80% AM 1kHz

10 V/m

80 MHz – 2,7 GHz

385MHz (18Hz Pulse Modulation)

27 V/m

450MHz (FM+/- 5KHz deviation

1kHz sine or 18Hz Pulse

Modulation)

28 V/m

710MHz (217Hz PM)

9 V/m

745MHz (217Hz PM)

9 V/m

780MHz (217Hz PM)

9 V/m

810MHz (18Hz PM)

28 V/m

870MHz (18Hz PM)

28 V/m

930MHz (18Hz PM)

28 V/m

1720MHz (217Hz PM)

28 V/m

1845MHz (217Hz PM)

28 V/m

1970MHz (217Hz PM)

28 V/m

2450MHz (217Hz PM)

28 V/m

5240MHz (217Hz PM)

9 V/m

5500MHz (217Hz PM)

9 V/m

5785MHz (217Hz PM)

9 V/m

At 80 MHz and 800 MHz, the higher frequency

range applies.

These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects

and people.

a

Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be

predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength

in the location in which the HC271/HC271p is used exceeds the applicable RF compliance level above, the HC271/HC271p should be observed to verify normal operation. If abnormal performance

is observed, additional measures may be necessary, such as reorienting or relocating the HC271/HC271p.

b

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

EMC Notice

Electromagnetic immunity

Immunity test

IEC 60601 Test levels

Compliance level

Electromagnetic environment–Guidance

Electrostatic discharge (ESD)

IEC 61000-4-2

±8 kV contact

±15 kV air

±8 kV contact

±15 kV air

Floors should be wood, concrete or ceramic tile. If floors are covered with

synthetic material, the relative humidity should be at least 30%.

Electrical fast transient/burst

IEC 61000-4-4






environment

Surge

IEC 61000-4-5






environment.

Voltage dips, short interruptions

and voltage variations on power

supply input lines

IEC 61000-4-11

< 5%

U

T

1 (> 95% dip in

U

T

) for

0.5 cycle, 40%

U

T

(60% dip in

U

T

)

for 5 cycles, 70%

U

T

(30% dip in

U

T

) for 25 cycles, < 5%

U

T

(>95%

dip in

U

T

) for 5s

< 5%

U

T

(> 95% dip in

U

T

) for 0.5

cycle, 40%

U

T

(60% dip in

U

T

) for

5 cycles, 70%

U

T

(30% dip in

U

T

)

for 25 cycles, < 5%

U

T

(>95% dip

in

U

T

) for 5s


environment. If the user of the HC271/HC271p requires continued operation

during interruptions in the main power, it is recommended that the HC271/

HC271p be powered from an uninterruptible power supply or a battery.

Power frequency

(50 Hz) magnetic field

IEC 61000-4-8

30 A/m

30 A/m

Power frequency magnetic fields should be at least characteristic of a typical

location in a typical commercial or hospital environment.

Conducted RF induced by RF fields

IEC 61000-4-6

3 Vrms 150 kHz - 80 MHz 6Vrms


3 Vrms 150 kHz - 80 MHz, 6Vrms


Portable and mobile RF communications equipment should be used no

closer to any part of the OEV262H, including cables, than the recommended

separation distance calculated from the equation appliance to the frequency

of the transmitter. Recommended separation distance: d = 1.2 √P, d = 1.2

√P 80 MHz to 800 MHz, d = 2.3 √P 800 MHz to 2.7 GHz, where P is the

maximum output power rating of the transmitter in watts (W) according to the

transmitter manufacturer and d is the recommended separation distance in

meters (m). Field strengths from fixed RF transmitters, as determined by an

electromagnetic site survey

a

, should be less than the compliance level in each

frequency range

b

. Interference may occur in the vicinity of equipment marked

with following symbol:

Radiated RF EM fields and

Proximity fields from RF wireless

communications equipment

IEC 61000-4-3

10 V/m, 80 MHz - 2,7 GHz,

80% AM 1kHz

10 V/m

80 MHz – 2,7 GHz

385MHz (18Hz Pulse Modulation)

27 V/m

450MHz (FM+/- 5KHz deviation

1kHz sine or 18Hz Pulse

Modulation)

28 V/m

710MHz (217Hz PM)

9 V/m

745MHz (217Hz PM)

9 V/m

780MHz (217Hz PM)

9 V/m

810MHz (18Hz PM)

28 V/m

870MHz (18Hz PM)

28 V/m

930MHz (18Hz PM)

28 V/m

1720MHz (217Hz PM)

28 V/m

1845MHz (217Hz PM)

28 V/m

1970MHz (217Hz PM)

28 V/m

2450MHz (217Hz PM)

28 V/m

5240MHz (217Hz PM)

9 V/m

5500MHz (217Hz PM)

9 V/m

5785MHz (217Hz PM)

9 V/m

At 80 MHz and 800 MHz, the higher frequency

range applies.

These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures, objects

and people.

a

Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be

predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered. If the measured field strength

in the location in which the HC271/HC271p is used exceeds the applicable RF compliance level above, the HC271/HC271p should be observed to verify normal operation. If abnormal performance

is observed, additional measures may be necessary, such as reorienting or relocating the HC271/HC271p.

b

Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.

Electromagnetic emissions

The HC271/HC271p is intended for use in the

electromagnetic environment specified below. The

customer or the user of the HC271/HC271p should assure

that it is used in such an environment.

Emissions test

Compliance

Electromagnetic

environment–

Guidance

RF emissions

CISPR 32

Group 1

The HC271/HC271p

uses RF energy only

for its internal function.

Therefore, its RF

emissions are very low

and are not likely to

cause any interference

in nearby electronic

equipment.

RF emissions

CISPR 32

Class B

The HC271/HC271p

is suitable for use in

all establishments,

including domestic

establishments

and those directly

connected to the public

low-voltage power

supply network that

supplies buildings used

for domestic purposes.

Harmonic

emissions

IEC 61000-3-2

Class D

Voltage

fluctuations/

flicker emissions

IEC 61000-3-3

Complies

Disposal of waste equipment

by users

This symbol means do not dispose of your

product with your other household waste.

Instead, you should protect human health

and the environment by handing over your waste

equipment to a designated collection point for the

recycling of waste electrical and electronic

equipment. For more information, please contact

your household waste disposal service or go to

http://www.hp.com/recycle.

FCC Statement

This device complies with Part 15 and Part 18

of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not

cause harmful interference, and (2) this device

must accept any interference received, including

interference that may cause undesired operation.

Electromagnetic emissions

The HC271/HC271p is intended for use in the

electromagnetic environment specified below. The

customer or the user of the HC271/HC271p should assure

that it is used in such an environment.

Emissions test

Compliance

Electromagnetic

environment–

Guidance

RF emissions

CISPR 32

Group 1

The HC271/HC271p

uses RF energy only

for its internal function.

Therefore, its RF

emissions are very low

and are not likely to

cause any interference

in nearby electronic

equipment.

RF emissions

CISPR 32

Class B

The HC271/HC271p

is suitable for use in

all establishments,

including domestic

establishments

and those directly

connected to the public

low-voltage power

supply network that

supplies buildings used

for domestic purposes.

Harmonic

emissions

IEC 61000-3-2

Class D

Voltage

fluctuations/

flicker emissions

IEC 61000-3-3

Complies

Disposal of waste equipment

by users

This symbol means do not dispose of your

product with your other household waste.

Instead, you should protect human health

and the environment by handing over your waste

equipment to a designated collection point for the

recycling of waste electrical and electronic

equipment. For more information, please contact

your household waste disposal service or go to

http://www.hp.com/recycle.

FCC Statement

This device complies with Part 15 and Part 18

of the FCC Rules. Operation is subject to the

following two conditions: (1) this device may not

cause harmful interference, and (2) this device

must accept any interference received, including

interference that may cause undesired operation.

S

N

HP Healthcare Edition HC271 Product Notice AMS

HP Healthcare Edition HC271 Manual

HP Healthcare Edition HC271 manual content summary: