HP LH6000r HP Netserver LXr 8000 Surestore E Installation Guide
HP LH6000r - NetServer - 0 MB RAM Manual
View all HP LH6000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP LH6000r manual content summary:
- HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 1
information specific to your cluster configuration that you will need during installation of your cluster. • HP NetServer Microsoft Cluster Installation Guide - This is the first of two documents used to install the cluster. It covers the installation of all cluster supported HP NetServers and - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 2
version of the HP NetServer Microsoft Cluster Installation Guide. This later version changes the product name from "AutoRAID 12H" to "SureStore E 12H" and the shared storage HBA model number from "A5252A" to "A5252B." Clarified and corrected wording for Local Storage controllers. See Version History - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 3
defines the supported HP NetServer LXr 8000 with A3700AB HP SureStore E 12H Disk Array configurations for Microsoft Cluster Server. These configurations minimize single points of failure (SPOF), provide maximum availability, and have been certified by Hewlett-Packard and Microsoft. This guide is - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 4
Tested Products List. May not use embedded RAID, NetRAID-1, NetRAID-3, or NetRAID-1Si. Any HP cables that meet SCSI specifications and any SCSI bus speed HP A5252B Wide Differential SCSI Adapter 1 - 3 per NetServer Adaptec AHA-294X/AHA-394X/AIC-78XX SCSI Controller driver in NT 4.0 SP4 or later P3 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 5
use the same driver as the Intra-cluster LAN. 1 minimum P6 Shared Storage Cabling This part of the guide defines the allowable cabling configurations for Change name here? NetServer clusters using the HP SureStore E 12H Disk Array. Only these cabling configurations and cables are supported. These - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 6
A5252B SCSI HBA A5252B SCSI HBA HP Microsoft Cluster Server with a single HP SureStore E 12H Disk Array 4 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 7
A5252B SCSI HBA A5252B SCSI HBA HP Microsoft Cluster Server and two daisy-chained HP SureStore E 12H Disk Arrays 5 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 8
Changed from AutoRAID 12H to SureStore E 12H and the shared storage HBA from A5252A to A5252B. The earlier version of this guide states both that the NetRAID-3Si controller can and can not be used when indeed it can be used for local storage. Therefore, this change clarifies and corrects wording - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 9
HP NetServer Microsoft Cluster Installation Guide with Shared Storage System Supplement Rack Storage/12FC Rack Storage/12 Rack Storage/8 Storage System/6 HP SureStore E 12H Disk Array or HP A3661B Model 30/FC High Availability Disk Array 10 October 1999 (See Version History below) - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 10
This page intentionally left blank. HP NetServer Installation Guide 2 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 11
Microsoft Corp. • Windows and Windows NT are trademarks of Microsoft Corporation. • 3M is a registered Trademark of the 3M Company. Hewlett-Packard Network Server Division 10955 Tantau Avenue Cupertino, CA 95014-0770, USA © Copyright 1999, Hewlett-Packard Company HP NetServer Installation Guide 3 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 12
FILE SYSTEMS...31 7 MICROSOFT CLUSTER SERVER SOFTWARE SETUP 37 INSTALL MSCS ON SYSTEM A...37 INSTALL MSCS ON SYSTEM B...41 INSTALL SERVICE PACK OR HOT FIX ...41 8 CLUSTER TESTING ...42 HARDWARE VERIFICATION AND LABELING UTILITY 42 CLUSTER INSTALLATION TEST...42 HP NetServer Installation Guide 4 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 13
local storage. Added installation instructions in part 5 for the LC3. Initial release Intended Audience The guide is for the person who installs, administers, and troubleshoots the Microsoft Cluster Server. Hewlett-Packard assumes this person is qualified to service computer equipment and trained - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 14
A Graphical Overview to Setting Up the Cluster CAUTION Departing from the sequence shown here can cause unnecessary work and unpredictable results. HP NetServer Installation Guide 6 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 15
Windows NT, version 4.0 and Service Pack (SP). See the Configuration Guide for your cluster solution for the applicable Windows NT and SP versions and Microsoft Cluster Server installation software. NOTE Some HP NetServers, as stated in part "5 NetServer Software Setup," require installing Windows - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 16
• Torx™ T-25 driver supplied in the Rack Installation Toolkit. For rack installed clusters only. • Portable Field Service Grounding Kit (3M® part number 8505, or equivalent). Need More Help? HP Information Assistant provides extensive support information and is available on the HP NetServer Online - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 17
to the Shared Storage Systems and must be installed in specific PCI slots. See the Configuration Guide for your cluster configuration for the HP NetServer PCI slots to use. See instructions supplied with the component or see part "2 NetServer Hardware Setup" of the Shared Storage Supplement for - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 18
3 Shared Storage Hardware Setup part "3 Shared Storage Hardware Setup" in the Shared Storage Supplement HP NetServer Installation Guide 10 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 19
Guide under Plan on the HP NetServers Clustering Solutions web site. Racked clusters - Follow the Road Map supplied with the system and instructions in Connect Shared Storage & Cable the Cluster part "4 Cluster Cabling and Setup" in the Shared Storage Supplement HP NetServer Installation Guide 11 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 20
the Microsoft Service Pack On page ... 12 13 14 15 17 19 21 25 27 28 28 30 LCII Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 21
addresses must be on different subnets. LC3 Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from the CD and displays the Navigator Main - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 22
sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from , disable the Embedded IDE Hard Disk Controller. (The embedded IDE controller is not used on HP NetServer systems.) 8. Save and - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 23
driver version as specified in the Configuration Guide for your cluster. If you are using two HP D5013A NICs, load the driver NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 24
in part "1 What's Needed" for additional information. 1. Remove the HP NetServer Navigator CD, insert the boot floppy for Windows NT4.0, and exit Navigator to reboot the server. 2. When Setup prompts to detect mass storage devices, skip detection and manually specify the mass storage drivers: • The - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 25
D5013A NIC drivers must be manually set to the correct LAN speed. Log on and from the start menu select: Settings, Control Panel, NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 26
drivers you need. If you are using the embedded SCSI channels, load the Symbios driver at this time. 4. Continue the installation and select the following options when prompted: • Choose the unpartitioned space and install Windows NT. • Choose NTFS file system HP NetServer Installation Guide - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 27
4 These procedures provide instructions for servers using NetRAID, SureStore E 12H, and Model 30/FC shared storage solutions. Configure NetServer Hardware and BIOS 6. Make sure you power down System A and power up System B. 7. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 28
Configuration Guide for your cluster. If you are using two HP D5013A NICs, load the driver twice, once for the intra-cluster NIC and once for the client NIC. • Make sure TCP/IP Protocol is selected. Other protocols may be selected in addition, but TCP/IP is required. HP NetServer Installation Guide - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 29
and Shared Storage) on page 25. Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. If you have special NetServer local SCSI bus options enter the Symbios utility - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 30
in part "1 What's Needed" for additional information. 1. Remove the HP NetServer Navigator CD, insert the boot floppy for Windows NT4.0, and exit Navigator to reboot the server. 2. When Setup prompts to detect mass storage devices, skip detection and manually specify the mass storage drivers: • The - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 31
storage, you must use two adapters. Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. If you have special NetServer local SCSI bus options enter the Symbios utility - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 32
server. 2. When Setup prompts to detect mass storage devices, skip detection and manually specify the mass storage drivers: 3. Load drivers using the NetRAID-3Si Cluster Firmware and Driver floppy disk you created in part 1 "What's Needed" and the NT 4.0 Drivers . HP NetServer Installation Guide 24 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 33
Do not use the Auto setting. LX/LXr Pro Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive of System B and restart the server. The server boots from the CD and displays the Navigator Main menu - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 34
These procedures provide instructions for servers using NetRAID, SureStore E 12H, and Model 30/FC shared storage solutions Configure NetServer Hardware and BIOS 1. Make sure you power down System A and power up System B. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 35
the server. 2. When Setup prompts to detect mass storage devices, skip detection and manually specify the mass storage drivers: • The drivers are loaded from the NT 4.0 Drivers floppy disk you created from the Navigator CD. • First, load the driver for the device you want to boot from. For drives in - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 36
procedures provide instructions for servers using Fibre Channel shared storage solutions (HP Rack Storage/12FC. Configure NetServer Hardware and BIOS 1. System A and System B can both be powered on. 2. Insert the HP NetServer Navigator CD in the CD-ROM drive and restart the server. 3. During reboot - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 37
with Service Pack 3 at this time. NOTE Do not install the Microsoft Cluster Server Software (MSCS) at this time. NOTE After completing these procedures, power down System B and power up System A. Repeat all of the procedures in this part for System A. HP NetServer Installation Guide 29 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 38
For Fibre Channel solutions using the Rack Storage/12FC simply reboot System B and repeat the procedures on Systems A. Both systems can be powered up. HP NetServer Installation Guide 30 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 39
you identified. An example display follows: NOTE Disk Administrator lists disks in order, beginning with local (non-shared) disks followed by the shared disk arrays. HP NetServer Installation Guide 31 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 40
dialog appears indicating the maximum size of a single drives. 3. Click OK to include the full disk in the partition (the default). In the following example, Disk 1 has been partitioned and Disk Administrator assigned a temporary drive letter to the disk array. HP NetServer Installation Guide - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 41
Disk Administrator, Partitioned Disk Array NOTE Do not partition a disk into separate drives. Microsoft Cluster Server Software will only manage one partition per disk. 4. Repeat steps 1 through assigned the next sequential letter to the disk array. HP NetServer Installation Guide 33 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 42
Drive Letter. Disk Administrator displays the Assign Drive Letter dialog. 3. In the dialog, select a drive letter, and click OK. To avoid confusion later, HP recommends that you choose sequential drive letters. The example in this guide uses drive letters X and Y. HP NetServer Installation Guide - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 43
box to select one of the arrays that you just partitioned and assigned a drive letter. Disk Administrator highlights the selected disk. 2. From the Disk Administrator's field type a label (name) for the drive. Choose a descriptive label such as "Shared Drive X.". HP NetServer Installation Guide 35 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 44
. 6. Repeat steps 1 through 5 to format each drive to be shared in the cluster. The following example depicts both drives formatted with permanent drive letters assigned. Disk Administrator, Formatting and Assigning Volume labels 7. Exit Disk Administrator. HP NetServer Installation Guide 36 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 45
CD of Microsoft Windows NT Server, Enterprise Edition in the CD-ROM drive of System B. 2. Run the Microsoft Cluster Server setup program. Setup.exe Cluster Server software setup of System A. Click Next. Microsoft Cluster Administrator, Assigning a Cluster Name HP NetServer Installation Guide 37 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 46
correct MS Domain account, consult the Windows NT documentation supplied with your system. 7. Setup presents a two-column systems. Normally you would share all disks listed. Microsoft Cluster Server Setup, Assigning Shared Disks to the Cluster 8. Setup prompts HP NetServer Installation Guide 38 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 47
IP Address already filled in. However, your configuration may display the Client LAN first. Microsoft Cluster Server Setup, Assigning a Network Name to the intra-cluster LAN 10. Repeat the previous step for has the highest priority. See the example dialog below. HP NetServer Installation Guide 39 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 48
specifications and starts the cluster service. 15. Microsoft Cluster Server is now fully installed on System A. Reboot System A. 16. To finish installation of the Microsoft Cluster Server, leave System A running, go to the next procedure and install MSCS on System B. HP NetServer Installation Guide - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 49
not already downloaded clusfixi.exe, see "Software" in part "1 What's Needed." 2. Install the Microsoft hotfix clusfixi.exe on System A and System B. NOTE When downloading the file, refer to the Microsoft readme file for instructions on installing the hotfix. HP NetServer Installation Guide 41 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 50
to download this program. Run CIT Follow the instructions in the CIT program. If additional information is needed refer to CIT on-line help. CIT help is context sensitive and has been expanded to provide detailed instructions for each step of the program. HP NetServer Installation Guide 42 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 51
HP SureStore E 12H Disk Array Supplement to HP NetServer Microsoft Cluster Installation Guide October 10, 1998 (See Version History below) - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 52
this manual: Microsoft® is an U.S. registered trademark of Microsoft Corporation. WindowsTM and Windows NTTM are trademarks of Microsoft Corporation. Enterprise NetServer Division 5301 Stevens Creek Boulevard P.O. Box 58059 Santa Clara, CA 95052-8059, USA © Copyright 1998, Hewlett-Packard Company - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 53
?...5 2 NETSERVER HARDWARE SETUP...6 INSTALLING THE HP A5252B SCSI HOST BUS ADAPTER 6 3 SHARED STORAGE HARDWARE SETUP 7 IDENTIFY CONTROLS AND CONNECTORS ...7 INSTALL DISK MODULES ...9 INSTALL CONTROLLER BATTERIES ...10 INSTALL CONTROLLER MODULES...11 CONNECTING DISK ARRAY POWER CORDS...12 POWER UP - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 54
E 12H Disk Array as shared storage in an HP NetServer cluster. This supplement is incomplete without the HP NetServer Cluster Installation Guide. When prompted in this supplement, return to the HP NetServer Cluster Installation Guide for more information on installing the other components of - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 55
the HP SureStore E 12H Disk Array. These documents are included with the disk array. • HP SureStore E 12H Disk Array User's And Service Manual • HP SureStore E 12H Disk Array System Administrator's Guide for HP-UX and Windows NT To part 1 of the HP NetServer Microsoft Cluster Installation Guide 5 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 56
SPU I/O slot to use. NOTE The A5252B uses the standard Windows NT SCSI driver included with NT 4.0 Service Pack 3, so it is not necessary to install an additional driver. Refer to the Cluster Configuration Guide for more information. To part 2 of the HP NetServer Microsoft Cluster Installation - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 57
on your NT cluster. NOTE Refer to the HP SureStore E 12H Disk Array User's And Service Manual for instructions on rack mounting the disk array. Identify Controls and Connectors The various controls and connectors used during installation of the HP SureStore E 12H Disk Array are shown in Figure - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 58
Connector 1 5 - P1-P3 AC Power Connectors Figure 2. Disk Array Rear Panel 1 - Power Module Status Light 5 - Control Panel Display 2 - Disk Module Status Light 3 - Fan Module Status Light 4 - Power/Standby Switch 6 - Control Panel Status Light 7 - Controller Module Status Light Figure 3. Disk - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 59
Install Disk Modules NOTE To improve enclosure cooling and balance the load on the internal SCSI buses, the disk modules should be installed from left to right and from top to bottom. Disk module SCSI addresses are automatically preset by the backplane inside the disk array enclosure upon - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 60
The two battery packs included with the controller module must be installed before the controller module is installed in the disk array. 1. Remove the not secured properly, it could prevent the removal of the controller module once it is installed in the disk array enclosure. Figure 5. Installing - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 61
function properly. Also, do not attempt to install the controller module upsidedown. 1. Pull the controller module levers all the way out. 2. Insert the controller module into the disk array, while pushing on both sides of the controller module. 3. When the enclosure engages the levers, press the - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 62
strips as shown in Figure 7. NOTE The disk array cannot operate on a single power supply; consequently, the disk array will shutdown if power to two of the power supplies is lost. However, by connecting the third power supply to a different power strip, the disk array will shut down properly if - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 63
switch door up, then press the power/standby switch to the power on (in) position. 2. Wait for the control panel to display "Ready", indicating that the disk array has successfully completed its initialization and is ready for use. NOTE If the controller batteries are fully discharged, it may - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 64
These settings control the drive number 0, then press Enter. 5. Set the capacity size to the default of 100 MB (megabytes), then press Enter. 6. When prompted to Confirm, press Enter. NOTE Make sure you leave the disk array power on after completing these steps. To part 3 of the HP NetServer - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 65
be made in a specific manner so that the appropriate redundancy and, therefore, high availability requirements are met. Use the diagrams included in this supplement or the diagrams in the Cluster Configuration Guide for your cluster configuration. To part 4 of the HP NetServer Microsoft Cluster - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 66
Figure 9. SCSI Bus Cabling for Connecting One Disk Array 16 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 67
Figure 10. SCSI Bus Cabling for Connecting Multiple Disk Arrays 17 - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 68
the control panel to display "Ready", indicating that the disk array has successfully completed its initialization and is ready for use. Install SureStore E Manager Software Install the SureStore E Manager software on both servers. 1. Insert the HP SureStore E on Windows NT CD into the CD-ROM drive - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 69
is properly connected to the servers. This includes proper termination of the SCSI bus. • Make sure there is at least one logical drive created on the disk array. A logical drive should have been created in Step 3 of the "Configure the Disk Array Using the Control Panel" procedure performed earlier - HP LH6000r | HP Netserver LXr 8000 Surestore E Installation Guide - Page 70
configuration of the disk array hardware, logical drive 0 was created on the disk array. This logical drive is reserved for exclusive access by the SureStore Manager software and should not be formatted or used for data storage. To part 6 of the HP NetServer Microsoft Cluster Installation Guide 20
Microsoft Cluster Installation Documentation
for
HP NetServer LXr 8000
with A3700AB HP SureStore E 12H Disk Array
To assist you in installing your HP NetServer Microsoft Cluster, this file contains the documents
listed below in one pdf file.
•
Installation Overview
- This page provides an overview of the installation steps provided in
the Installation Guide.
•
Configuration Guide
- This guide provides configuration information specific to your cluster
configuration that you will need during installation of your cluster.
•
HP NetServer Microsoft Cluster Installation Guide
- This is the first of two documents used
to install the cluster.
It covers the installation of all cluster supported HP NetServers and the
cluster software, and references the Shared Storage Supplement for installation and setup of the
shared storage.
•
Shared Storage Supplement
- This supplement is specific to the shared storage device you are
using and must be used with the installation guide.
It provides instructions for installing and
setting up your shared storage devices.
10 October 1999
(See next page)