HP MSA2312sa HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas
HP MSA2312sa Manual
View all HP MSA2312sa manuals
Add to My Manuals
Save this manual to your list of manuals |
HP MSA2312sa manual content summary:
- HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 1
HP 2000 G2 Modular Smart Array Controller Firmware M113R11 Release Notes HP Part Number: 508849-014 Published: February 2012 Edition: 14 - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 2
© Copyright 2009, 2012 Hewlett-Packard Development Company, L.P. - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 3
HP MSA2000 G2 controllers running firmware versions M110R25 or M110R28 that will eventually cause controller configuration information to be lost, with subsequent loss of management capability from that controller. Array management : A MSA model. (TS=P2000 G3, M=MSA2000 G2, J=MSA2000) xxx Firmware - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 4
• HP 2324i G2 Modular Smart Array (HP MSA2324i G2) • HP 2324sa G2 Modular Smart Array (HP MSA2324sa G2) Operating systems Operating systems supported for use with the HP MSA2000 G2 family of products and when installing the binary firmware package: • Citrix XenServer HP Enterprise Editions • HP-UX - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 5
a drive is removed or marked as down while any utility is in progress on a vdisk. • A master-to down while rebooting the other controller during a firmware update. • If the array was power-cycled at for drives that do not respond to Task Management Functions. • Spare drives were not used correctly - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 6
controller. • An NTP time offset caused the time on the controller to be set incorrectly. • Added an additional prompt when expanding vdisks. • In HP SIM, the status of a single-controller array statuses were reporting on the two controllers in a dual-controller system. • After a firmware update - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 7
firmware using Smart Components-Linux environments" (page 10) • "Installing firmware using the Storage Management Utility (SMU)" (page 11) • "Installing firmware using FTP" (page 12) • "Installation troubleshooting" (page 13) Installation notes and best practices WARNING! Do not cycle power or - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 8
event logs. • Updating array controller firmware may result in new event messages that are not described in earlier versions of documentation. For comprehensive event message documentation, see the most current version of the HP 2000 G2 Modular Smart Array Reference Guide. • The Smart Component - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 9
/s where CPxxxxxxx.exe is the downloaded Smart Component filename ip_address is the management IP address of the array controller username is the username account with management rights password is the password for username When prompted for logon information, enter credentials for an account - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 10
HP products is available from the HP Business Support Center website at http://www.hp.com/support/ password contains an exclamation mark (!), enclose the string in single quotes or enter a backslash (\) before the exclamation point. For example, '!manage' or \!manage. 5. Follow onscreen instructions - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 11
Storage Management Utility (SMU) 1. Obtain the firmware package and save it to a temporary directory. Firmware for all HP products is available from the HP Business Support Center website at http://www.hp.com/support has completed. In dual-controller systems with Partner Firmware instructions 11 - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 12
HP products is available from the HP Business Support Center website at http://www.hp.com/support controllers. b. Verify that the system FTP service is enabled. c. Verify that the user you will log in as has permission to use the FTP interface and has manage completed. In dual-controller systems with - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 13
, proceed to the next troubleshooting step. 3. Verify that all system controllers are operating properly. For controllers; cycle power on the controller enclosure.) • If the show disks command from all controllers is successful, perform the firmware update process again. Installation instructions - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 14
were omitted from the MSA2000 G2 documentation. For controller failover to function properly, change the default driver parameters as follows: ◦ QLogic - Port Down Retry Count = 60, Link Down Timeout = 60 ◦ Emulex - LinkTimeOut = 60, NodeTimeOut = 60 • Issue: Storage Management Utility is slow or - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 15
Storage Management Utility Restore System Defaults function is not available. • Workaround: The Restore System Defaults function is listed in the User Guide : When an MSA2000 G2 array is exposed to back in manually. There are HP products and is not currently supported. Avoid this issue by - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 16
Volume Vol-300 as LUN ID 1 on ports A2 and B2. • Issue: Changing both IP addresses causes problems accessing Storage Management Utility. • Workaround: Changing the IP address for both controllers concurrently can cause the controllers to become unavailable. First, change the IP address on the - HP MSA2312sa | HP 2000 G2 Modular Smart Array Controller Firmware M113R10 Releas - Page 17
controller mode, some event log descriptions can indicate a second controller. HP c-Class BladeSystem environment, VMWare may fail I/O during failover operations. • Workaround: The VMWare kernel parameter ResetOnFailover must be set to 0 in order for array Volume Set and Default Mapping pages of
HP 2000 G2 Modular Smart Array Controller
Firmware M113R11 Release Notes
HP Part Number: 508849-014
Published: February 2012
Edition: 14