HP MSA2312sa HP MSA2000/P2000 Drive Module Replacement Instructions
HP MSA2312sa Manual
 |
View all HP MSA2312sa manuals
Add to My Manuals
Save this manual to your list of manuals |
HP MSA2312sa manual content summary:
- HP MSA2312sa | HP MSA2000/P2000 Drive Module Replacement Instructions - Page 1
=12169& prodSeriesId=3971509 ◦ P2000 G3 MSA Guided Troubleshooting: http://www.hp.com/go/p2000/ troubleshooting ◦ User manual for your MSA product model: http://www.hp.com/go/hpsc • Leave failed modules in the enclosure until you are ready to install the replacement module. Removing a module from an - HP MSA2312sa | HP MSA2000/P2000 Drive Module Replacement Instructions - Page 2
Verifying drive status Before and after replacing a drive, determine its status: • Check operating system event logs, product-specific logs, and management utilities for drive health and location information. • Check enclosure status LEDs. • Check drive LEDs, as described in the following image and - HP MSA2312sa | HP MSA2000/P2000 Drive Module Replacement Instructions - Page 3
see the following resources for your MSA product model: • Guided Troubleshooting • User Manual • SMU Reference Guide • CLI Reference Guide Updating firmware After installing any new component, verify that it is running the latest firmware. Go to the HP Support Center website and navigate to the page - HP MSA2312sa | HP MSA2000/P2000 Drive Module Replacement Instructions - Page 4
: HP Support Center: http://www.hp.com/go/hpsc HP Product Bulletin: nl http://www.hp.com/go/productbulletin HP SPOCK: http://www.hp.com/storage/spock HP Servers: http://www.hp.com/go/servers HP Storage: http://www.hp.com/go/storage HP MSA: http://www.hp.com/go/msa MSA2000 G2 Guided Troubleshooting
-
1 -
2 -
3 -
4
 |
 |
HP MSA2000/P2000
nl
Drive Module
nl
Replacement Instructions
Abstract
This document details procedures for replacing failed drive
modules in HP MSA2000- and P2000-family controller and
drive enclosures. Read this entire document before replacing
a drive. Incorrectly removing a operational, failing, or failed
drive from an enclosure might cause data loss.
© Copyright 2012, 2013 Hewlett-Packard Development Company, L.P.
*712258-002*
HP Part Number: 712258-002
Published: April 2013
Edition: 2
Before you begin
•
Before proceeding, check the following:
Confirm that the drive is a member of a
fault-tolerant configuration that permits
◦
removing one or more drives without risking
data loss.
◦
If multiple drives have failed and need
replacing, determine how many drives can be
replaced at the same time. The number of
drives that can fail and be replaced without
data loss is determined by the fault-tolerance
level of the configuration.
For additional information on replacing drives,
go to the following HP websites:
◦
MSA2000 G2 Guided Troubleshooting:
h
t
tp://h20
5
8
4.w
w
w2
.hp
.co
m/hpgt/gui
de
s/
s
e
lec
t?lang=e
n&cc=u
s&pr
odT
y
peI
d=1
2
1
6
9&
pr
odS
e
r
i
e
sI
d=3
9
7
1
5
0
9
◦
P2000 G3 MSA Guided Troubleshooting:
h
t
tp://w
w
w
.hp
.co
m/go/p2000/
tr
o
u
ble
sh
oo
ting
◦
User manual for your MSA product model:
h
t
tp://w
w
w
.hp
.co
m/go/hp
s
c
•
Leave failed modules in the enclosure until you
are ready to install the replacement module.
Removing a module from an operational enclosure
significantly changes air flow within the enclosure.
Openings must be populated for the enclosure to
cool properly.
•
Parts can be damaged by electrostatic discharge.
Keep parts in electrostatic containers until needed
and ensure you are properly grounded when
touching static-sensitive components.
•
Use care when handling drives. Drives are
sensitive electromechanical devices that can be
permanently damaged through improper
handling. Keep drives in their original, protective
packaging until installation.
•
The replacement drive module must be of the
same type, and possess capacity equal to or
greater than the one being replaced.
Page 1