HP Model 735 2GB disk drive user notes (a1658-90691)
HP Model 735 - Workstation Manual
 |
View all HP Model 735 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Model 735 manual content summary:
- HP Model 735 | 2GB disk drive user notes (a1658-90691) - Page 1
the following message: "If model number: "disk-drive", is guide or your disk drive installation guide instructions on the last page of this document. Also, the following patches are necessary to run diagnostics: HP-UX 9.03 through 9.07 - PHSS_6798 HP-UX 10.01 - PHSS_6794 HP-UX 10.10 - PHSS_7071 The HP - HP Model 735 | 2GB disk drive user notes (a1658-90691) - Page 2
A0 A1 A2 J6 LM SS SCSI B B ID 0 1 2 3 4 5 6 J2 Term Power from Drive CAUTION Do NOTuse the jumper plugs for J2 on J6. You will damage the internal contacts Seagate ST32151N Disk Drive Jumpers
-
1 -
2
 |
 |
This device cannot be installed as a standalone device at
HP–UX 9.03.
To install 2–GB drives on HP–UX 9.03, you must
use a
netdist
install server.
You must install patch PHSS_5776 on
the server to recognize 2-GB drives.
For systems operating with HP-UX release 9.05, you must load
patch PHCO_5881 for
disktab
and
sam
functionality, and patch
PHSS_5776 for network installation functionality.
The software patches may be obtained from HP Customer Service.
To install patch PHCO_5881 to HP–UX, perform the following
steps:
1.
Begin the HP-UX software installation process. If the system
has a one of the drives installed, the following message ap-
pears:
“Note: the destination disk type “
disk–drive
”
was not found in the disk table /etc/disktab.
(Press any key to continue.)”
2.
Press any key. The screen displays the following message:
“If model number: “
disk–drive
”, is incorrect,
and a correct one (one that has an entry in
the /etc/disktab) is known, please enter it
now otherwise press return.”
3.
T
ype:
DEC_DSP3210S
Return
The DEC_DSP3210S drive is functionally equivalent to the
new drives. By using this entry, you can complete the software
installation process.
4.
Let the software installation process complete.
5.
Install the appropriate patch using
/etc/update
and reboot the
system.
2–GB Disk Drive
User Notes
Refer to your workstation owner’s guide or your disk drive installation
guide for detailed information about installing your disk drive. During
the installation procedure, you may have to change the SCSI ID of your
disk drive. Refer to the appropriate illustration to set the SCSI ID
jumpers to the desired SCSI ID.
NOTICE:
We recommend that you use SCSI ID 6 for your
workstation’s first hard disk drive, and SCSI ID
5 for the second hard disk drive.
Minimum
Software
Requirements
The 2–GB disk drive is fully operational with HP-UX Release 9.03 and
later on Series 700 systems (releases 9.03, and 9.05 require patches to
the operating system).
Please see the patch instructions on the last page
of this document.
Also, the following patches are necessary to run diagnostics:
HP-UX 9.03 through 9.07 – PHSS_6798
HP-UX 10.01 – PHSS_6794
HP-UX 10.10 – PHSS_7071
The HP part numbers for these drives are A1658–60009 (spare) and
A1658–69009 (exchange).
Part Number A1658–90691
Edition E0596
Printed in U.S.A.
*A1658-90691*