HP Model 735 fast wide differential 2GB, 4GB disk drive user notes (a1658-9070
HP Model 735 - Workstation Manual
 |
View all HP Model 735 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Model 735 manual content summary:
- HP Model 735 | fast wide differential 2GB, 4GB disk drive user notes (a1658-9070 - Page 1
is fully operational with HP-UX Release 10.01 and later on Series 700 binary-compatible systems, and at HP-UX Releases 9.05 and 9.07, this drive may be used as a non-bootable device. Patches are required to most operating systems. Please see the following table and the patch instructions on the last - HP Model 735 | fast wide differential 2GB, 4GB disk drive user notes (a1658-9070 - Page 2
Seagate ST32171WD and ST34371WD Disk Drive Jumpers Quantum - Atlas II - XP32181WD and XP34361WD Disk Drive Jumpers The HP part numbers for the 2-GB drives are A1658-60010 (spare) and A1658-69010 (exchange). The HP part numbers for the 4-GB drives are A1658-60011 (spare) and A1658-69011 (exchange).
-
1 -
2
 |
 |
You will not be able to load HP-UX 9.03 on a standalone, newly
installed
2–GB
drive.
To install HP–UX 9.03 on 2–GB drives, you
must use a
netdist
install server.
You must install patch PHSS_5776 on the
netdist
install server to
recognize
2-GB
drives for both HP-UX 9.03 and 9.05.
After you have loaded HP-UX onto the either the
2–GB
or
4–GB
drive, you must load patch PHCO_7461 for
disktab
and
sam
func-
tionality.
Install the patches using
/etc/update
.
To load HP-UX
9.05
onto a newly installed standalone
2–GB
drive,
prior to loading the patches, perform the following steps:
1.
Begin the HP-UX software installation process. The follow-
ing message appears:
“Note: the destination disk type
“
disk–drive–model–number
” was not found in
the disk table /etc/disktab.
(Press any key to continue.)”
2. Press
any key
. The screen displays the following message:
“If model number: “
disk–drive–model–number
”,
is incorrect, and a correct one (one that
has an entry in the /etc/disktab) is known,
please enter it now otherwise press return.”
3. Press:
<Return>
(or
<Enter>
)
The screen displays a message about using default parameters.
4. Press
any key.
5.
Let the software installation process complete.
The software patches may be obtained from HP Customer Service.
INSTRUCTIONS FOR HP-UX 9.X
After you have loaded HP–UX onto the new drive, install the
appropriate patches using
swinstall
and reboot the system.
INSTRUCTIONS FOR HP-UX 10.X
2- and 4-GB
(Fast-Wide-Differential)
Disk Drive User Notes
Refer to your workstation owner’s guide or your disk drive installation
guide for detailed information about installing your disk drive. During
the installation procedure, you may have to change the SCSI ID of your
disk drive. Refer to the appropriate illustration to set the SCSI ID
jumpers to the desired SCSI ID.
NOTICE:
We recommend that you use SCSI ID 6 for your
workstation’s first hard disk drive, and SCSI ID
5 for the second hard disk drive.
Minimum
Software
Requirements
The
2-GB
disk drive is fully operational with HP-UX Release 9.03 and
later on Series 700 binary–compatible systems.
The
4-GB
disk drive is fully operational with HP-UX Release 10.01 and
later on Series 700 binary–compatible systems, and at HP-UX Releases
9.05 and 9.07, this drive may be used as a non-bootable device.
Patches are required to most operating systems. Please see the following
table and the patch instructions on the last page of this document.
HP-UX
Version
Patches
– OS
Patches – Diags
9.03 (2–GB)
PHCO_7461, PHSS_5776
PHSS_7587
9.05
PHCO_7461, PHSS_5776(2–GB)
PHSS_7587
9.07
N/A
PHSS_7587
10.01
PHKL_8904, PHKL_8329
PHSS_7583
10.10
PHKL_8906
PHSS_7585
10.20
PHKL_8908
PHSS_7929
Part Number A1658–90709
Edition E0297
Printed in U.S.A.
*A1658-90709*