HP Model 748 Rack Mount Kit Installation Note for Models 745/132L and 748 Indu
HP Model 748 - VME Workstation Manual
View all HP Model 748 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP Model 748 manual content summary:
- HP Model 748 | Rack Mount Kit Installation Note for Models 745/132L and 748 Indu - Page 1
Models 745/132L and 748 Industrial Systems Notices Information in this Note is subject to change without notice. Hewlett-Packard makes no warranty of any kind about this manual your local Sales and Service Office. CopyrightE Hewlett- Precautions CAUTION: S Use of the HP E3664A Rail Kit is required for - HP Model 748 | Rack Mount Kit Installation Note for Models 745/132L and 748 Indu - Page 2
Back Out. You may want to remove the feet. 465.5 mm 101.6 mm EIA Standard rack mount for Model 745. 465.5 mm 235.0 mm EIA Standard rack mount for Model 748. 1. Attach the flange and spacer with flange screws. CAUTION: Spacer must be outside of flange or screws will bind internal modules. Get - HP Model 748 | Rack Mount Kit Installation Note for Models 745/132L and 748 Indu - Page 3
the feet. 1. Set the workstation upside down, then pry the three front cover bottom catches loose. 465.5 mm 235.0 mm EIA Standard Wall Mount for Model 748. 1. Pull off the power switch button, then press the switch arm in to ON. 2. Pry side catches loose and work front cover off the - HP Model 748 | Rack Mount Kit Installation Note for Models 745/132L and 748 Indu - Page 4
Part Number: A2677-90011 Printed in U.S.A. Edition E0698 *A2677-90011* 4
1
Rack Mount Kit Installation Note
For Models 745/132L and 748 Industrial Systems
Notices
Information
in this Note is subject to change without notice.
Hewlett-Packard makes no warranty of any kind about this manual, including, but not limited to, the implied warranties of mer
-
chantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or
direct, indirect, special, incidental or consequential damages about the furnishing, performance, or use of this material.
Warranty
A copy of the specific warranty terms applicable to your Hewlett-Packard product and replacement parts can be obtained from your
local Sales and Service Of
fice.
Copyright
E
Hewlett-Packard Company 1993, 1997, 1998
This Note contains information which has been protected by copyright.
All rights are reserved.
Reproduction, adaptation, or
translation without prior written permission is prohibited, except as allowed under the copyright laws.
Safety Precautions
CAUTION:
S
Use
of the HP E3664A Rail Kit is r
equir
ed for safe rack mounting.
Multiple units stacked
directly
on top of each other r
equir
e only one rail kit on the bottom–most unit.
S
If the system will be installed in a closed or multi–unit rack, ensure the ambient temperature does not
exceed 55
_
C (131
_
F).
S
Ensure the airflow is suf
ficient for safe operation of the system.
S
Mount the system in such a way to prevent a hazardous condition due to uneven loading.
S
Do not connect the system’
s power cord to a power extension strip.
Shut down the application and operating system, then turn of
f the system at both the front panel pushbutton and the power supply
switch. Remove the interface cables and power cord(s) before installing this rack mount kit.
W
ARNING: Get two people to help you hold the system in position while installing it. A fully configur
ed Model 745 weighs
over 27 Kg (60 pounds); a fully configurted 748 weighs over 31 Kg (68 pounds).
Parts List
Installation Options
Item
4U Flange
4U Spacer
7U Spacer
Flange screw
Dress screw (with
745
2
2
4
4
4
Part Number
A2261–00037
A2261–00039
A2261–00040
0515–1114
0570–1366
0590–0804
nylon washer)
Clip nut
W
all Mount
Y
our installation may require dif
ferent dress
screws and clip nuts.
Qty.
Rack Mount
Mast Mount
Back
Front
Out
Out
748
2
6
4
Qty.
7U Flange
A4500–00009
2
Dress screw (with
0570–1597
nylon washer)
4
745
and 748
748 only
748 only