HP NC382m HP Broadcom iSCSI Boot for NC382x Adapters User Guide
HP NC382m - PCI Express Dual Port Multifunction Gigabit Server Adapter Manual
View all HP NC382m manuals
Add to My Manuals
Save this manual to your list of manuals |
HP NC382m manual content summary:
- HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 1
HP Broadcom iSCSI Boot for NC382x Adapters User Guide Part Number 512354-003 November 2009 (Third Edition) - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 2
license. Microsoft, Windows, and Windows Server are U.S. registered trademarks of Microsoft Corporation. Intended audience This document is for the person who installs, administers, and troubleshoots servers and storage systems. HP assumes you are qualified in the servicing of computer equipment - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 3
Overview...4 Overview ...4 Limitations ...4 System requirements ...4 Installation and configuration ...6 Downloading the SoftPaq ...6 Configure the server for iSCSI boot...6 Enable iSCSI boot and set the boot order 6 Configure iSCSI parameters...7 Option ROM settings ...8 Windows Server 2008 R2 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 4
HP NC-Series Broadcom iSCSI Boot Package for Windows. All accelerated iSCSI commands are handled by the adapter's HP iSCSI HBA driver. This feature is applied to all HP Multifunction Gigabit Ethernet Server Adapters at no additional cost for standup and mezzanine adapters; however, some embedded HP - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 5
following Multifunction Gigabit Server Adapters are supported. o HP NC382T PCI Express Dual Port Multifunction Gigabit Server Adapter o HP NC382i Integrated Quad Port PCI Express Gigabit Server Adapter o HP NC382m Dual Port 1 GbE Multifunction BL-c Adapter • Targets. All Microsoft certified iSCSI - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 6
.hp.com/#Support). 2. Click Support & Drivers. 3. Select Download drivers and software (and firmware). 4. Type the adapter name in the For product box, and then click Go. 5. Select an operating system. 6. Click HP NC-Series Broadcom iSCSI Boot Package for Windows. 7. Click download and save the HP - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 7
one of the following: o Enabled for Windows Server 2003 or Windows Server 2008 if using the Offloaded iSCSI method of OS installation. o Disabled for Windows Server 2008 Non-offloaded iSCSI method of OS installation. 6. Press to exit the General Parameters Configuration Screen and then select - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 8
Exit Configuration screen and then select Exit and Save the Configurations. Dynamically configure iSCSI parameters In a dynamic configuration the For the Windows HBA Boot Mode parameter, select Enabled. 7. Modify the iSCSI Name parameter based on the DHCP options that are used by the DHCP server. o - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 9
Windows Server 2008 Non-offloaded iSCSI method of OS installation, supply the bxvbd.inf and bxnd.inf files. Windows Server 2008 installation Optionally add MF drivers to WIM image You may optionally add the HP Multifunction Gigabit Server Adapters to the WIM image. Installation and configuration - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 10
iSCSI driver 1. Locate the HP Windows Server 2008 Multifunction Gigabit Server Adapter component CPxxxxxx.exe file obtained in "Downloading the SoftPaq File." Extract the contents to a USB memory device. 2. Select Enable for the Windows HBA Boot Mode parameter. For more information, see "Configure - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 11
. For more information, see "Configure iSCSi parameters (on page 7)." 3. Boot the Windows Server 2008 DVD. Navigate to the setup screen and select the Load Drivers option and then browse the USB device for the HP Windows Server 2008 Multifunction Gigabit Server Adapter driver files for your specific - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 12
hotfix KB943295 (http://support.microsoft.com/kb/943295). a. See the Microsoft article KB814847 (http://support.microsoft.com/kb/814847) for details about how to create a Microsoft slipstream CD. 4. Insert the slipstream Microsoft Windows 2003 SP2 CD and press F6. Installation and configuration 12 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 13
5. Select drivers from the disk 1 and disk 2 diskettes when prompted. DO NOT insert disk 1 into drive A until prompted. After disk 1 is inserted, the following window appears. 6. Enter an S to select Specify Additional Device. The following window appears. Installation and configuration 13 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 14
Select Install 1st: MS Windows wdfldr and then press Enter. b. Select Install 2nd: MS Windows wdf01000 and then press Enter. c. Select Install 3rd: HP NCXXX Virtual Bus Driver and then press Enter. 9. Insert disk 2 and press Enter when the following window appears. Installation and configuration 14 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 15
10. Press Enter to load the HP iSCSI HBA Driver. 11. A Windows setup screen shows the iSCSI Target. Installation and configuration 15 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 16
, insert disk 1 and press Enter. 14. If the following window appears, insert disk 2 and press Enter. Windows Server 2003 continues installing on the iSCSI target. Before the GUI installation begins, it may be necessary to configure the option ROM setting "BOOT TO ISCSI" to Enabled. Installation and - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 17
using offload iSCSI (Broadcom's offload iSCSI driver) but it is required for all non-offload deployments (also known as Microsoft Initiator). 6. Go to c:\cpqsystem\pnpdrvs\iscsiutils and execute the hpsetcrash*.cmd. 7. At this point in Windows Server 2008, iSCSI boot may be configured to boot with - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 18
all Installation Options as indicated below and please note that the MPIO option cannot be added to a file system that is being used by an iSCSI Boot client after it has been created during the deployment phase. 3. Complete the installation and reboot when prompted. Installation and - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 19
Troubleshooting Known issues Known issues for Microsoft iSCSI Initiator boot installation • If you do not select an Adapter Service Name by highlighting it during initial Microsoft Initiator boot setup, the setup continues without an error but does not select an NDIS driver for booting. The deployed - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 20
problems Symptoms: The initiator is able to connect to and log in to the target and the system recognizes the disk but you are unable to install the operating system. Possible causes: • There are multiple HP Multifunction Gigabit Server adapters enabled in the system. Installation and configuration - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 21
LUN from which to boot (some targets start numbering data devices at 1 not 0). • The target is not configured to allow access to the specified LUN by the initiator. • The Slipstream CD creation step contains an error causing F6 phase to fail. Check for the following problems: o Insure the folder and - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 22
hardware or software • Operating system type and revision level HP contact information For the name of the nearest HP authorized reseller: • See the Contact HP worldwide (in English) webpage (http://welcome.hp.com/country/us/en/wwcontact.html). For HP technical support: • In the United States, for - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 23
and abbreviations BRCM Broadcom BSOD blue screen of death CHAP Challenge Handshake Authentication Protocol DHCP Dynamic Host Configuration Protocol HBA host bus adapter iLO Integrated Lights-Out iLO 2 Integrated Lights-Out 2 INF setup information file IPL initial program load iSCSI Internet Small - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 24
LUN logical unit number MPIO multipath I/O PXE Preboot Execution Environment QFE quick fix engineering RBSU ROM-Based Setup Utility RILOE Remote Insight Lights-Out Edition SAN storage area network VLAN virtual local-area network WIM Windows Imaging file format Acronyms and abbreviations 24 - HP NC382m | HP Broadcom iSCSI Boot for NC382x Adapters User Guide - Page 25
9 F files, downloading 6 H HP contact information 22 I Install Microsoft iSCSI Software Initiator 17 installation and configuration 6 iSCSI boot 4 iSCSI boot targets 4, 11, 19 L LUN access problems 20 M Microsoft Windows 2008 DVD 9, 10 O OS problems 20 overview 4 P Post installation 17 S support 22
HP Broadcom iSCSI Boot for NC382x Adapters
User Guide
Part Number 512354-003
November 2009 (Third Edition)