HP NetServer LP 1000r HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo
HP NetServer LP 1000r Manual
View all HP NetServer LP 1000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP NetServer LP 1000r manual content summary:
- HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 1
HP Netserver LXr 8500 with NetRAID-4M (HP Rack Storage/12) Windows NT® Server 4.0 Enterprise Edition Cluster Configuration Guide 6 June 2001 (see Versions at the end of this document) Introduction This document defines the configurations that Hewlett-Packard supports for the HP Netserver LXr 8500, - HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 2
Windows NT® Server 4.0 Enterprise Edition SP6a HP NetServer LXr 8500 700 MHz 2 - 8 ASPN Release 8 Any size 128 MB minimum. Must be HP. 3 See drive bays or HP external drive cabinet (e.g., HP Rack Storage/12) Must be HP Any HP cables that meet SCSI specifications and any SCSI bus speed Any HP NetRAID- - HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 3
. It may not be used for client communication. Client LAN Any LAN HP D5013B (10/100TX PCI) Hptxnt.sys 4.02.35 (Navigator L.20.00) or later 1 Any that is on both the HP Tested Products List and the Microsoft® Hardware Compatibility List. Vendor supported driver NOTE If the NIC used is the same as - HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 4
local storage drives. Here, a NetRAID-1Si is in slot P5. 3. Cables between the servers and shared storage cabinets can be any HP LVD SCSI (offset) cable up to 10 meters. See "Cables"for Rack Storage/12 in the guide for a list of cables that can be used. NetRAID-4M 01 23 HP Netserver LXr 8500 - HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 5
Power Cabling to Separate Power Circuits 5 - HP NetServer LP 1000r | HP Netserver LXr 8500 NetRAID-4M Config Guide for Windo - Page 6
Versions 6 June 2001 Initial release © Copyright 2001, Hewlett-Packard Company 6
1
HP Netserver LXr 8500
with
NetRAID-4M (HP Rack Storage/12)
Windows NT
Server 4.0 Enterprise Edition
Cluster Configuration Guide
6 June 2001
(see
Versions
at the end of this document)
Introduction
This document defines the configurations that Hewlett-Packard supports for the HP Netserver LXr 8500,
HP Rack Storage/12 and Microsoft
Cluster Server.
These configurations minimize single points of
failure (SPOF) and provide extended availability.
The specific configuration certified and supported by
both Hewlett-Packard and Microsoft
is defined, as are other guidelines to assist you in configuring your
clustered Netservers.
This guide is prescriptive; it describes the configurations supported by HP.
Any
deviance to these configurations can result in an inoperative cluster or an operating cluster with degraded
performance, hidden SPOFs, etc., and therefore will not be supported by HP.
What's Defined in a Cluster
•
Cluster
•
SPUs
•
Local and Shared Storage
•
Intra-cluster and Client LANs
•
Shared Storage Cabling
Cluster
Type of SPUs
HP Netserver LXr 8500
Each node must be the same SPU, but may have different clocks speeds,
main memory sizes, cache sizes, and number of CPUs.
Number of nodes
2
Shared Storage
HP Rack Storage/12 with HP NetRAID-4M controller and HP disks.
See
Shared Storage
below.
LANs:
Client LAN
Any NIC that is HP and Microsoft
approved.
See
Client LAN
below.
Intra-cluster
(Heartbeat) LAN
HP D5013B with crossover cable or equivalent. See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptible power