HP NetServer LT 6000r Installing TurboLinux Server on an HP Netserver
HP NetServer LT 6000r Manual
 |
View all HP NetServer LT 6000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP NetServer LT 6000r manual content summary:
- HP NetServer LT 6000r | Installing TurboLinux Server on an HP Netserver - Page 1
drivers. ©Copyright Hewlett-Packard Company (This document is only available in English.) November 31, 2001 (Rev: 20011031) Introduction This document was created by Hewlett-Packard for the purpose of helping you install Turbolinux Server 6.5 on your HP NetServer, based on procedures tested by HP - HP NetServer LT 6000r | Installing TurboLinux Server on an HP Netserver - Page 2
tables", please choose to initialize all the hard drives. 1. Power on the server, and insert the Turbolinux Server 6.5 Install CD in the CD tray to start the installation. 2. At the prompt boot: press Enter. If you need to load device drivers in a particular order, type install noprobe. 3. At - HP NetServer LT 6000r | Installing TurboLinux Server on an HP Netserver - Page 3
provide. The amount of swap space required also varies depending on the amount of RAM in the system. The following partitioning scheme is given as an example. 9. Create a boot partition. A. Select DOS FREE under /dev/sda. B. Click Add a partition. C. Select partition type Linux ext2. D. Set the - HP NetServer LT 6000r | Installing TurboLinux Server on an HP Netserver - Page 4
manufacturers and model types. If your monitor is not listed, select Unknown monitor and manually enter the horizontal and vertical sync rates. NOTE: Entering wrong horizontal and/or vertical the installation. Congratulations! You just installed Turbo Linux Server 6.5! Remove the CD from the drive. - HP NetServer LT 6000r | Installing TurboLinux Server on an HP Netserver - Page 5
On-Line Information and Software Sources TurboLinux Inc., web access: http://www.turbolinux.com HP web access: http://www.hp.com HP Server Online Documentation CD (included with your system): includes all server documentation online
-
1 -
2 -
3 -
4 -
5
 |
 |
TurboLinux Server 6.5 Installation Guide
for HP NetServers
NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version
M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web
site as a reference to install an operating system, be sure to also check the HP web site for the latest available
drivers.
©Copyright Hewlett-Packard Company
(This document is only available in English.)
November 31, 2001 (Rev: 20011031)
Introduction
This document was created by Hewlett-Packard for the purpose of helping you install
Turbolinux Server 6.5 on your HP NetServer, based on procedures tested by HP. The
objective of this document is to provide the information needed to achieve the following
tasks.
±²
Install Turbolinux Server 6.5 from CD-ROM.
±²
Configure network settings.
Features
Turbolinux Server 6.5 includes the Linux 2.2 kernel (2.2.18), and a number of packages
such as samba, squid, IP chains and the apache web server. It also support Korean,
Chinese and Japanese in addition to English.
Requirements
Disk Space
: A full installation of Turbolinux Server 6.5 requires 1175 MB.
Hardware settings
: You will need to know the following information to complete the
installation:
±²
The monitor's resolution, color depth, and refresh rate.
±²
The display (graphics) adapter manufacturer and model number.
±²
The Ethernet card manufacturer, model number, IRQ, and I/O address.
Other requirements: