HP NetServer LT 6000r Installing SCO UnixWare on an HP Netserver
HP NetServer LT 6000r Manual
 |
View all HP NetServer LT 6000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP NetServer LT 6000r manual content summary:
- HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 1
guide. NOTE: The SCO UnixWare 2.1 and UnixWare 7. X operating system is supported on the HP NetServer LC II, LC 3, LD Pro, LH Plus, LH Pro, LH II, LH 3, LH4, LX Pro, LXe Pro, LXr Pro product families. The SCO UnixWare 7.X operating system is supported on the HP NetServer LPr LC2000, LH3000 - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 2
HP-Supplied Controllers Troubleshooting Section 2. Installing SCO UnixWare 2.1.x Large Memory Access SCSI Extended Translation Setting MPS Table Setting On NetServer LS and LX for UnixWare HP Bundled NICs Not Supported commands exactly as instructed. Almost all UNIX commands are in lower case so if - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 3
the first channel, Hard Disk 0 is the first hard disk, etc. Set Up All Cards In ECU SCO UNIX likes to have all cards and disk drives configured in CMOS to Host Bus Adapter Drivers diskette, and the HP Drivers diskette (produced from the HP NetServer Navigator CD). Swap Space You may wish to increase - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 4
drivers are available from SCO on their Host Bus Adapter Drivers disk. HP ships the SCO PTF3124C version of the adsl driver on the driver diskette that is created by the HP NetServer Navigator CD. Driver Names for HP-Supplied Controllers The following table lists the names of required drivers for - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 5
mega LH 6000 Symbios896 slha & mega LT 6000r Symbios896 slha & mega NOTE: HP currently does not support ultra SCSI mode on the AIC7880 controllers when they are connected to the HP Storage System 6. Ultra SCSI mode is supported for disks installed in the HP NetServer cabinet. Troubleshooting - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 6
have drivers for UnixWare 2.1.x at this time. Consult SCO's hardware compatability guide for a supported NIC. Installing SCO UnixWare 2.1.x The following instructions help you to install SCO UnixWare 2.1.x on your HP NetServer system. NOTE: In general, UnixWare can not share IRQs across different - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 7
that is created by the HP NetServer Navigator CD. 1. Use the HP Navigator CD-ROM installation utility to configure your system hardware. This utility creates the HP NetServer UnixWare 2.1.x Drivers diskette (the "Drivers Diskette"). 2. UnixWare 2.1.0 and 2.1.1 have problems with system memory sizes - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 8
7.1.x The following instructions will help you to install SCO UnixWare 7.1.x on your HP NetServer system. NOTE: HP Navigator CD-ROM installation utility to configure your system hardware. This utility creates the HP NetServer UnixWare 7.1.x Drivers diskette for HP NetRaid, latest HBA Drivers and HP - HP NetServer LT 6000r | Installing SCO UnixWare on an HP Netserver - Page 9
can cause conflict wilth the HP NetRAID card. - Return to DCU main menu and Save @ Exit. 5. Follow the instructions in the SCO UnixWare Installation FTP: ftp.sco.com HP Internet (World-Wide-Web) site: http://www.hp.com HP Server Online Documentation CD (included with your system): includes
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
 |
 |
HP Server
SCO UnixWare Installation Guide
NOTICE: The information in this document was last updated for the HP NetServer Navigator CD-ROM version
M.04.05. If you don't have the M.04.05 version CD-ROM and you're obtaining this document from the HP web
site as a reference to install an operating system, be sure to also check the HP web site for the latest available
drivers.
©Copyright Hewlett-Packard Company
January 22, 2002
Introduction
This document presents important information that you need to install SCO UnixWare.
The first section of this document is a list of helpful tips on NOS installation, the second
section is a step-by-step installation guide.
NOTE: The SCO UnixWare 2.1 and UnixWare 7. X operating system is
supported on the HP NetServer LC II, LC 3, LD Pro, LH Plus, LH Pro, LH II, LH
3, LH4, LX Pro, LXe Pro,
LXr Pro product families.
The SCO UnixWare 7.X operating system is supported on the HP NetServer LPr
LC2000, LH3000, LH6000, LT6000r, LXr8000, and LXr8500 product families.
The SCO UnixWare 2.1, UnixWare 7.X operating system is
not
supported on the
HP NetServer E 30, E 40, E 45, E 50, E 60, LC, LC Plus, LE, LF, LH, LM, and
LS product families.
The SCO UnixWare 7.1.1 operating system is
not
supported on the HP Server
tc3100 and tc4100 product families.
Hewlett-Packard has more than one Disk Array Controller (DAC) for the
NetServer product family.
In this document the term "HP Disk Array" refers to
the EISA and PCI Disk Array Controller models C3609A and C3610A,
respectively.
The term "HP NetRAID" refers to the HP NetRAID and NetRAID-
1 PCI DAC models D4943A and D4992A, The term "HP NetRAID 3Si" refers to
model number D5955A. The term "HP NetRAID 1Si refers to model number
D2140A. The term"HP Embedded RAID" refers to the built in RAID controller
on the HP NetServer LH3, LH4, LH3000, LH6000 and LT6000r.
The HP NetRAID disk array controllers will be supported on UnixWare 2.1 and
UnixWare 7.X on a future HP NetServer Navigator release.