HP NetServer LT 6000r HP Netserver LPr with XP256 Cluster Config Guide for Wi
HP NetServer LT 6000r Manual
View all HP NetServer LT 6000r manuals
Add to My Manuals
Save this manual to your list of manuals |
HP NetServer LT 6000r manual content summary:
- HP NetServer LT 6000r | HP Netserver LPr with XP256 Cluster Config Guide for Wi - Page 1
Configuration Guide 08 February, 2000 Introduction This document defines the supported HP NetServer LPr configurations with the XP256 and Microsoft Cluster Server. These configurations minimize single points of failure (SPOF), provide maximum availability, and have been certified by Hewlett-Packard - HP NetServer LT 6000r | HP Netserver LPr with XP256 Cluster Config Guide for Wi - Page 2
speed No. of CPUs BIOS version CPU cache RAM No. of power supplies Local storage I/O slots: HP NetServer LPr. 400, 450, 500, or 550 MHz 2 - 4 4.06.14PR Any size 256 MB minimum. Must be HP. 3 See Local Storage below. P1 - P4 Shared storage controller P2 - NetRAID-3Si local storage P3 - Client LAN P4 - HP NetServer LT 6000r | HP Netserver LPr with XP256 Cluster Config Guide for Wi - Page 3
3G x 36= 262.8G Disk Capacities RAID levels Max number of LUNs Port Host Server #1 of the cluster, the other to Server #2 (see diag 1, page 5). A3724A HP-10 port Short Wave FC Hub A4839A HP-10 port Long Wave FC Hub 1 per SPOF cluster 1 cluster on 1 hub Fibre Channel Switch Model Fabric Support - HP NetServer LT 6000r | HP Netserver LPr with XP256 Cluster Config Guide for Wi - Page 4
. It may not be used for client communication. Client LAN Any LAN HP D5013A (10/100TX PCI) 3.27.00.0001 or later 1 P4 Any that is on both the HP Tested Products List and the Microsoft Hardware Compatibility List. Any driver NOTE If the NIC used is the same as the Intra-cluster - HP NetServer LT 6000r | HP Netserver LPr with XP256 Cluster Config Guide for Wi - Page 5
Shared Storage Cabling This part of the guide defines the allowable cabling configurations for clusters using the HP NetServer LPr and the XP256. Only these cabling configurations and cables are supported. DIAGRAMS SHOWING THE SUPPORTED CONFIGURATIONS LPr LPr LPr LPr Hub/Switch XP256 XPX2P56
1
HP NetServer LPr
with
XP256 (Fibre Channel or SCSI)
Cluster Configuration Guide
08 February, 2000
Introduction
This document defines the supported HP NetServer LPr configurations with
the XP256 and Microsoft
Cluster Server.
These configurations minimize single points of failure (SPOF), provide maximum
availability, and have been certified by Hewlett-Packard or Microsoft.
This guide is prescriptive; it
describes the configurations supported by HP.
Any deviance to these configurations can result in an
inoperative cluster or an operating cluster with degraded performance, hidden SPOFs, etc., and therefore
will not be supported by HP.
What’s Defined in a Cluster
Cluster
SPUs
Local and Shared Storage
Intra-cluster and Client LANs
Shared Storage Cabling
Cluster
Type of SPUs
HP NetServer LPr.
Each node must be the same model SPU, but may have different clocks
speeds, main memory sizes, cache sizes, and number of CPUs (2, 3, or 4).
Number of nodes
2
Shared Storage
XP256 with FC or SCSI connections.
See
Shared Storage
below.
LANs:
Client LAN
Any NIC that is HP and Microsoft approved.
See
Client LAN
below.
Intra-cluster
(Heartbeat) LAN
HP D5013A with crossover cable. See
Intra-cluster LAN
below.
Power source
Direct from power mains, power conditioner or uninterruptible power
supply (UPS) using any power conditioner or UPS.
System software:
Navigator version
L.16.05 or later
Operating System
Microsoft Windows NT Server 4.0, Enterprise Edition or later
Service pack
SP5 or later