HP Officejet 6500A User Guide - Page 98

Paper is not picked up from the input tray, Cause, Solution 4: Clean the printhead, Solution, Power - power cord

Page 98 highlights

Chapter 8 Cause: Ink levels are too low. Solution 4: Clean the printhead Solution: Complete the printhead cleaning procedure. For more information, see Clean the printhead. The printhead may need to be cleaned if the printer was turned off incorrectly. NOTE: Turn off the printer by pressing the Power button located on the printer. Wait until the Power light turns off before unplugging the power cord or turning off a power strip. If you incorrectly turn off the printer, the print carriage might not return to the correct position causing problems with the ink cartridges and print quality issues. Cause: The printhead was clogged. Solution 5: Load paper in the input tray Solution: If the printer has only a few sheets remaining, load more paper in the input tray. If there is plenty of paper in the input tray, remove the paper, tap the stack of paper against a flat surface, and reload the paper into the input tray. For more information, see: Load media Cause: The printer picked up two sheets of paper. Paper is not picked up from the input tray Try the following solutions to resolve the issue. Solutions are listed in order, with the most likely solution first. If the first solution does not solve the problem, continue trying the remaining solutions until the issue is resolved. • Solution 1: Restart the printer • Solution 2: Make sure the paper is loaded correctly • Solution 3: Check the print settings • Solution 4: Clean the rollers • Solution 5: Check for a paper jam • Solution 6: Service the printer Solution 1: Restart the printer Solution: Turn off the printer, and then unplug the power cord. Plug the power cord back in, and then press the Power button to turn on the printer. Cause: The printer experienced an error. If this did not solve the issue, try the next solution. 94 Solve a problem

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250

Cause:
Ink levels are too low.
Solution 4: Clean the printhead
Solution:
Complete the printhead cleaning procedure. For more information, see
Clean the printhead. The printhead may need to be cleaned if the printer was turned
off incorrectly.
NOTE:
Turn off the printer by pressing the
Power
button located on the printer.
Wait until the
Power
light turns off before unplugging the power cord or turning
off a power strip. If you incorrectly turn off the printer, the print carriage might not
return to the correct position causing problems with the ink cartridges and print
quality issues.
Cause:
The printhead was clogged.
Solution 5: Load paper in the input tray
Solution:
If the printer has only a few sheets remaining, load more paper in the
input tray. If there is plenty of paper in the input tray, remove the paper, tap the stack
of paper against a flat surface, and reload the paper into the input tray.
For more information, see:
Load media
Cause:
The printer picked up two sheets of paper.
Paper is not picked up from the input tray
Try the following solutions to resolve the issue. Solutions are listed in order, with the most
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved.
Solution 1: Restart the printer
Solution 2: Make sure the paper is loaded correctly
Solution 3: Check the print settings
Solution 4: Clean the rollers
Solution 5: Check for a paper jam
Solution 6: Service the printer
Solution 1: Restart the printer
Solution:
Turn off the printer, and then unplug the power cord. Plug the power cord
back in, and then press the
Power
button to turn on the printer.
Cause:
The printer experienced an error.
If this did not solve the issue, try the next solution.
Chapter 8
94
Solve a problem