HP P Class 450/500/550/600/650/700/750 3Dlabs Wildcat III 6110 graphics accele
HP P Class 450/500/550/600/650/700/750 Manual
 |
View all HP P Class 450/500/550/600/650/700/750 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P Class 450/500/550/600/650/700/750 manual content summary:
- HP P Class 450/500/550/600/650/700/750 | 3Dlabs Wildcat III 6110 graphics accele - Page 1
Company 3404 East Harmony Road Fort Collins, Colorado 80528 Read Before Installing 3DLabs Wildcat III 6110 Graphics Accelerator Card HP Product No. A8051A General HP Installation Instructions NOTE Before you install your graphics card, refer to the your workstation's Technical Reference (www - HP P Class 450/500/550/600/650/700/750 | 3Dlabs Wildcat III 6110 graphics accele - Page 2
provided CD-ROM. 5. Refer to your workstation's Owner's Guide for instructions on how to verify your graphics configuration. For information on the original end-user. The type of service provided is return to an HP or repair-authorized reseller service-center. At Hewlett-Packard's discretion, a defective - HP P Class 450/500/550/600/650/700/750 | 3Dlabs Wildcat III 6110 graphics accele - Page 3
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and the Canadian Department of energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment - HP P Class 450/500/550/600/650/700/750 | 3Dlabs Wildcat III 6110 graphics accele - Page 4
ISO/IEC Guide 22 and EN 55022: 1994 Class B EN 50024:1998 Also compliant with. . . EN 61000-3-2: 1995 EN 61000-3-3: 1995 U.S. FCC Part 15, Class B Japan VCCI Class B Australia contact: European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Dept. HQTRE Standards
-
1 -
2 -
3 -
4
 |
 |
Hewlett-Packard Company
3404 East Harmony Road
Fort Collins, Colorado 80528
Read Before Installing
3DLabs Wildcat III 6110 Graphics Accelerator Card
HP Product No. A8051A
General HP Installation Instructions
NOTE
Before you install your graphics card, refer to the your workstation’s
Technical
Reference
(
www.hp.com/go/workstationsupport
) for important system
configuration information.
CAUTION
Graphic cards are susceptible to electrostatic shock. When handling your card
always wear a properly grounded wrist strap and handle the card carefully.
The latest workstation BIOS must be installed on your workstation
before
installing the new graphics card. The latest BIOS can be downloaded from
http://www.hp.com/go/workstationsupport. If the latest BIOS is not installed, you
may experience no video, PCI Option ROM errors and system stops during self-
test (POST).
In addition, if you have purchased and/or installed Windows
®
2000, a chipset
driver must be installed to enable AGP. If an AGP graphics card is not run in
AGP mode, you may experience extremely slow graphics performance, system
lockups and Windows
®
stop errors. The chipset driver can be downloaded from
1.
Before opening your w
orkstation to install the graphics card, disconnect all cables from the system. When refer-
ring to your system model/type and for obtaining the proper driver version, please use the AxxxxX nomenclature
found on the Serial Number plate on the back of the machine.
2.
Following the procedures described in your workstation’s
Technical Reference
, install the graphics board into the
AGP Pro slot (see the next diagram). Slide the board into the slot and ensure it is fully seated in the connector.
3.
Attach your monitor cable to the primary port. If you have two monitors, attach the primary monitor to the pri-
mary port and the second monitor to the secondary port. Use the included DVI-I dongle to attach an analog mon-
itor to the either port.