HP P Class 450/500/550/600/650/700/750 ATI Fire GL 8800 graphics card (read be
HP P Class 450/500/550/600/650/700/750 Manual
View all HP P Class 450/500/550/600/650/700/750 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P Class 450/500/550/600/650/700/750 manual content summary:
- HP P Class 450/500/550/600/650/700/750 | ATI Fire GL 8800 graphics card (read be - Page 1
HP Product No. A8050A General HP Installation Instructions NOTE Before you install your graphics card, refer to the your workstation's Technical Reference (www.hp . The chipset driver can be downloaded from http://www.hp.com/go/workstationsupport. 1. Before opening your workstation to install the - HP P Class 450/500/550/600/650/700/750 | ATI Fire GL 8800 graphics card (read be - Page 2
driver upgrades and the Card Installation Instructions as supplied by ATI go to: http://www.hp GL driver from the provided CD-ROM. 5. Refer to your workstation's Owner's Guide for instructions on The type of service provided is return to an HP or repair-authorized reseller service-center. At Hewlett - HP P Class 450/500/550/600/650/700/750 | ATI Fire GL 8800 graphics card (read be - Page 3
. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference - HP P Class 450/500/550/600/650/700/750 | ATI Fire GL 8800 graphics card (read be - Page 4
to ISO/IEC Guide 22 and EN 93/68/EEC This product was tested in a typical Hewlett-Packard workstation configuration. Original signed by Ruth Lutes, Site Quality Manager, Fort contact: European Contact: Your local Hewlett-Packard Sales and Service Office or Hewlett-Packard GmbH, Dept. HQTRE Standards
Hewlett-Packard Company
3404 East Harmony Road
Fort Collins, Colorado 80528
Read Before Installing
ATI Fire GL 8800 Graphics Accelerator Card
HP Product No. A8050A
General HP Installation Instructions
NOTE
Before you install your graphics card, refer to the your workstation’s
Technical
Reference
(
www.hp.com/go/workstationsupport
) for important system
configuration information.
CAUTION
When handling your card always wear a properly grounded wrist strap and
handle the card carefully due to susceptible electrostatic shock.
The latest BIOS must be installed on your workstation
before
installing the
new graphics card. The latest BIOS can be downloaded from
http://www.hp.com/go/workstationsupport. If the latest BIOS is not installed, you
may experience no video, PCI Option ROM errors and system stops during self-
test (POST).
In addition, if you have purchased and/or installed Windows
®
2000, a chipset
driver must be installed to enable AGP. If an AGP graphics card is not run in
AGP mode, you may experience extremely slow graphics performance, system
lockups and Windows
®
stop errors. The chipset driver can be downloaded from
1.
Before opening your w
orkstation to install the graphics card, disconnect all cables from the system. When refer-
ring to your system model/type and for obtaining the proper driver version, please use the AxxxxX nomenclature
found on the Serial Number plate on the back of the machine.
2.
Following the procedures described in your workstation’s
Technical Reference
, install the graphics board into the
appropriate AGP Pro slot (see the next diagram). Slide the board into the slot and ensure it is fully seated in the
connector.
3.
Attach your monitor cable to the primary port. If you have dual monitors, attach the primary monitor to the pri-
mary port. Use the included DVI-I to DB-15 dongle to attach an analog monitor to the secondary port.
A8050- 90002