HP P2000 HP P2000 G3 MSA System SMU Reference Guide - Page 139

flash, put T230R01-01.bin flash, To install an HP ROM Flash Component or firmware

Get HP P2000 PDF manuals and user guides View all HP P2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

7. Enter: put firmware-file flash For example: put T230R01-01.bin flash CAUTION: Do not perform a power cycle or controller restart during a firmware update. If the update is interrupted or there is a power failure, the module might become inoperative. If this occurs, contact technical support. The module might need to be returned to the factory for reprogramming. NOTE: If you attempt to load an incompatible firmware version, the message *** Code Load Fail. Bad format image. *** is displayed and after a few seconds the FTP prompt is redisplayed. The code is not loaded. Firmware update typically takes 10 minutes for a controller having current CPLD firmware, or 20 minutes for a controller having downlevel CPLD firmware. If the controller enclosure has attached drive enclosures, allow additional time for each expansion module (EMP) to be updated. This typically takes 2.5 minutes for an EMP in each P2000 drive enclosure or 3 minutes for an EMP in each MSA2000 drive enclosure. Expansion modules in D2700 or MSA70 drive enclosures must be updated separately. NOTE: If you are using a Windows FTP client, during firmware update a client-side FTP application issue can cause the FTP session to be aborted. If this issue persists try using SMU to perform the update, use another client, or use another FTP application. When firmware update on the local controller is complete, the message Operation Complete is printed, the FTP session returns to the ftp> prompt, and the FTP session to the local MC is closed. If PFU is enabled, allow an additional 10-20 minutes for the partner controller to be updated. 8. Quit the FTP session. 9. Clear your web browser's cache, then sign in to SMU. If PFU is running on the controller you sign in to, a dialog box shows PFU progress and prevents you from performing other tasks until PFU is complete. NOTE: After firmware update has completed on both controllers, if the system health is Degraded and the health reason indicates that the firmware version is incorrect, verify that you specified the correct firmware file and repeat the update. If the problem persists, contact technical support. Updating expansion-module firmware A drive enclosure can contain one or two expansion modules. Each expansion module contains an enclosure management processor (EMP). All modules of the same model should run the same firmware version. You can update the firmware in each expansion module by loading a firmware file obtained from the HP web download site, http://www.hp.com/go/p2000. To install an HP ROM Flash Component or firmware Smart Component, follow the instructions on the HP web site; otherwise, to install a firmware binary file, follow the steps below. You can specify to update all expansion modules or only specific expansion modules. If you specify to update all expansion modules and the system contains more than one type of enclosure, the update will be attempted on all enclosures in the system. The update will only succeed for enclosures whose type matches the file, and will fail for enclosures of other types. HP P2000 G3 MSA System SMU Reference Guide 139

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
HP P2000 G3 MSA System SMU Reference Guide
139
7.
Enter:
put
firmware-file
flash
For example:
put T230R01-01.bin flash
CAUTION:
Do not perform a power cycle or controller restart during a firmware update. If the
update is interrupted or there is a power failure, the module might become inoperative. If this
occurs, contact technical support. The module might need to be returned to the factory for
reprogramming.
NOTE:
If you attempt to load an incompatible firmware version, the message
*** Code Load
Fail. Bad format image. ***
is displayed and after a few seconds the FTP prompt is
redisplayed. The code is not loaded.
Firmware update typically takes 10 minutes for a controller having current CPLD firmware, or 20
minutes for a controller having downlevel CPLD firmware. If the controller enclosure has attached drive
enclosures, allow additional time for each expansion module (EMP) to be updated. This typically takes
2.5 minutes for an EMP in each P2000 drive enclosure or 3 minutes for an EMP in each MSA2000
drive enclosure. Expansion modules in D2700 or MSA70 drive enclosures must be updated separately.
NOTE:
If you are using a Windows FTP client, during firmware update a client-side FTP application
issue can cause the FTP session to be aborted. If this issue persists try using SMU to perform the
update, use another client, or use another FTP application.
When firmware update on the local controller is complete, the message
Operation Complete
is
printed, the FTP session returns to the
ftp>
prompt, and the FTP session to the local MC is closed.
If PFU is enabled, allow an additional 10–20 minutes for the partner controller to be updated.
8.
Quit the FTP session.
9.
Clear your web browser’s cache, then sign in to SMU. If PFU is running on the controller you sign in to,
a dialog box shows PFU progress and prevents you from performing other tasks until PFU is complete.
NOTE:
After firmware update has completed on both controllers, if the system health is Degraded
and the health reason indicates that the firmware version is incorrect, verify that you specified the
correct firmware file and repeat the update. If the problem persists, contact technical support.
Updating expansion-module firmware
A drive enclosure can contain one or two expansion modules. Each expansion module contains an
enclosure management processor (EMP). All modules of the same model should run the same firmware
version.
You can update the firmware in each expansion module by loading a firmware file obtained from the HP
web download site,
. To install an HP ROM Flash Component or firmware
Smart Component, follow the instructions on the HP web site; otherwise, to install a firmware binary file,
follow the steps below.
You can specify to update all expansion modules or only specific expansion modules. If you specify to
update all expansion modules and the system contains more than one type of enclosure, the update will be
attempted on all enclosures in the system. The update will only succeed for enclosures whose type matches
the file, and will fail for enclosures of other types.