HP P6300 HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins
HP P6300 Manual
View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P6300 manual content summary:
- HP P6300 | HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins - Page 1
/P6500 EVA Fibre Channel Controller Replacement Instructions About this document For the latest documentation, go to http:// www.hp.com/support/manuals, and select your product. The information contained herein is subject to change without notice. The only warranties for HP products and services - HP P6300 | HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins - Page 2
any failure messages received. HP Insight Remote Support Software provides a recommended fault monitoring solution. • Verify status using HP P6000 Command View: 1. In the navigation pane, select Storage system→Hardware→Controller Enclosure, and then select the controller. The status is displayed - HP P6300 | HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins - Page 3
DIMMs are being powered by battery (during AC power loss). Solid amber indicates a DIMM failure. 1. Halt I/O to the controller with HP P6000 Command View: a. In the navigation pane, select Storage System→Hardware→Controller Enclosure. b. Select the controller (Controller 1 or Controller 2) to halt - HP P6300 | HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins - Page 4
and slide the cover over the controller until the latch clicks into place. Figure 8 Installing the controller cover 4. Move the small form-factor pluggable (SFP) modules, installed in the unused FC host ports, from the controller being replaced to the new controller (if there are unused FC ports - HP P6300 | HP P6300/P6500 EVA Fibre Channel Controller Enclosure Replacement Ins - Page 5
properly: NOTE: Wait approximately 3 minutes for the system to check the component status. • Verify the controller health green LED is lit (see Table 1 (page 3)). If not, try reseating the controller in the enclosure. • From HP P6000 Command View, navigate to the component as described in the
HP P6300/P6500 EVA Fibre
Channel Controller
Replacement Instructions
© Copyright 2013 Hewlett-Packard Development Company, L.P.
Printed in Puerto Rico
*5697-2515*
HP Part Number: 5697-2515
Published: March 2013
Edition: 1
About this document
For the latest documentation, go to
h
t
tp://
w
w
w
.hp
.co
m/su
ppo
r
t/man
uals
, and select your
product.
The information contained herein is subject to change
without notice. The only warranties for HP products
and services are set forth in the express warranty
statements accompanying such products and services.
Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical
or editorial errors or omissions contained herein.
WARRANTY STATEMENT: To obtain a copy of the
warranty for this product, see the warranty information
website:
h
t
tp://w
w
w
.hp
.co
m/go/s
t
o
r
age
w
ar
r
an
t
y
NOTE:
All P6300/P6500 EVA documentation
also applies to P6350/P6550 storage systems.
Choosing a storage configuration
The P6300/P6350 EVA configuration details are:
•
Two HSV340 controllers per controller enclosure
•
Four SAS ports
•
Four 8 Gb FC ports per controller
•
1/10 (minimum/maximum) controller enclosures
•
8/120 (minimum/maximum) M6612 (LFF) disk
drives
•
8/250 (minimum/maximum) M6625 (SFF) disk
drives
The P6500/P6550 EVA configuration details are:
•
Two HSV360 controllers per controller enclosure
•
Eight SAS ports
•
Four 8 Gb FC ports per controller
•
2/20 (minimum/maximum) controller enclosures
•
8/240 (minimum/maximum) M6612 (LFF) disk
drives
•
8/450 (minimum/maximum) M6625 (SFF) disk
drives
Page 1