HP P6300 HP Controller Enclosure Cache DIMM Replacement Instructions (5697-134
HP P6300 Manual
View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P6300 manual content summary:
- HP P6300 | HP Controller Enclosure Cache DIMM Replacement Instructions (5697-134 - Page 1
the procedure in HP P6000 EVA Upgrade Instructions - P6300 to P6350 or P6500 to P6550. Observe the following precautions when replacing the cache DIMMs on a controller. CAUTION: HP recommends that you perform the replacement procedure within seven minutes. Ensure all necessary parts are available so - HP P6300 | HP Controller Enclosure Cache DIMM Replacement Instructions (5697-134 - Page 2
that you upgrade the firmware before you install the DIMM. Failure to do so results in failure of the array to boot. • Alloy (gray)-colored latches on components like the controller indicates that the component is warm-swappable. Halt the I/O of a controller being serviced with HP P6000 Command View - HP P6300 | HP Controller Enclosure Cache DIMM Replacement Instructions (5697-134 - Page 3
of the controller being serviced. Removing the wrong controller can result in data loss. 1. Halt I/O to the controller with HP P6000 Command View: a. In the navigation pane, select Storage System→Hardware→Controller Enclosure. b. Select the appropriate controller (Controller 1 or Controller 2) to - HP P6300 | HP Controller Enclosure Cache DIMM Replacement Instructions (5697-134 - Page 4
the socket (2, Figure 7 (page 4)). 3. Place the cover on the controller module rails and slide the cover over the controller until the latch clicks in place. Figure 8 Installing the controller cover Verifying operation After replacing the controller, check the following to verify the component is
HP Controller Enclosure
Cache DIMM Replacement
Instructions
© Copyright 2012 Hewlett-Packard Development Company, L.P.
Printed in Puerto Rico
*5697-1349*
HP Part Number: 5697-1349
Published: June 2012
Edition: 3
About this document
For the latest documentation, go to
h
t
tp://
w
w
w
.hp
.co
m/su
ppo
r
t/man
uals
, and select your
product.
The information contained herein is subject to change
without notice. The only warranties for HP products
and services are set forth in the express warranty
statements accompanying such products and services.
Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical
or editorial errors or omissions contained herein.
WARRANTY STATEMENT:
To obtain a copy of the warranty for this product, see
the warranty information website:
h
t
tp://w
w
w
.hp
.co
m/go/s
t
o
r
age
w
ar
r
an
t
y
Before you begin
XCS version 11001000 and later supports HP
P6350/P6550 EVAs with 2- or 4-GB DIMMs and large
capacity batteries. Upgrade kits are available that
include batteries, DIMMs, and an ABM. If you are
upgrading an HP P6300 to P6350 or an HP P6500
to P6550, HP recommends that you install an upgrade
kit. Because you must install the replacement
components in a specific order and the array must be
shutdown, follow the procedure in
HP P6000 EVA
Upgrade Instructions — P6300 to P6350 or P6500
to P6550
.
Observe the following precautions when replacing the
cache DIMMs on a controller.
CAUTION:
HP recommends that you perform
the replacement procedure within seven minutes.
Ensure all necessary parts are available so the
procedure can be completed without
interruption. Removing a controller module
significantly changes the air flow within the
enclosure. Both controllers must be installed for
the enclosure to cool properly. If a controller
fails, leave it in place in the enclosure until a
new module is available to install. The enclosure
could shut down due to overheating unless the
controller is replaced within the recommended
seven minutes.
Parts can be damaged by electrostatic
discharge. Use proper antistatic protection. See
to the documentation that shipped with your
system for additional information.
Page 1