HP P6300 HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248
HP P6300 Manual
View all HP P6300 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP P6300 manual content summary:
- HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 1
versions of HP Command View EVA. This guide is intended for field personnel and customers who are experienced with these array models, storage area networks, HP P6000 Command View and associated software. This guide does not provide information about upgrading or replacing array hardware. The - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 2
HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP see the warranty information website: http://www.hp.com/go/storagewarranty Acknowledgments Microsoft® and - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 3
33 Verifying installation on the management module 35 Upgrading browsers and JRE 35 HP Insight Remote Support software 35 Upgrading HP P6000 Replication Solutions Manager (optional 36 Monitoring array stability...36 Preparing the HP P6000 Continuous Access environment for an upgrade 38 Contents - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 4
the controller software 45 Resetting the I/O module...54 Step 6. Upgrading the disk drive firmware 55 Upgrading firmware on all disks 56 Upgrading firmware on a single disk 60 Step 7. Entering array passwords 60 Step 8. Resuming array operation 61 4 Troubleshooting 62 HP P6000 Command View - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 5
perform the upgrade procedures, ensure that your system meets the requirements. IMPORTANT: HP P6000 Command View (formerly HP StorageWorks Command View EVA) supports all HP P6000 Enterprise Virtual Arrays, EVA4000/6000/8000, EVA4100/6100/8100, EVA4400/6400/8400, and P63x0/P65x0 EVA storage systems - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 6
.com/support/manuals Release Notes Click Storage Software under storage, and then HP P6000 Command View Software Suite User Guide Yes select HP P6000 Command View Software under Storage Device Management Software. HP P6000 Command View Software Suite Installation Guide Yes HP Storage System - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 7
a software DVD or an E-Delivery kit. IMPORTANT: XCS 11200000 requires HP P6000 Command View 10.3 or later. For the latest HP P6000 Command View and XCS compatibility information, see Table 2.0, HP P6000 Command View interoperability support, in the HP P6000 Enterprise Virtual Array Compatibility - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 8
If you have questions or need assistance, go to http://welcome.hp.com/country/us/en/ wwcontact_us.html and select your country/region. 8 Getting started - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 9
. The tasks you perform depend on your system configuration and the HP P6000 Command View implementation. These tasks focus on upgrading system components to ensure they meet the supported configuration for XCS 11200000. NOTE: Be sure to record the XCS controller software version you are using - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 10
to complete: About 5 minutes When to perform: Anytime before the upgrade To check your controller software version, follow these steps: 1. Open HP P6000 Command View. 2. In the navigation pane, select the array you plan to upgrade. The Initialized Storage System Properties window opens. The version - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 11
version information for your current software. NOTE: For details on array software compatibility, see Table 1.0, HP P6000 software solution compatibility and Table 2.0, HP P6000 Command View interoperability support, in the HP P6000 Enterprise Virtual Array Compatibility Reference. See "Reference - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 12
1 Initialized Storage System Properties 2. Click Help in the Session pane. The full version number is displayed at the top of the online help window (Figure 2 (page 12)). If the version is earlier than the minimum supported version, it must be upgraded. Figure 2 HP P6000 Command View online help - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 13
user guide for your array model. See Table 1 (page 6) for links to these documents. TIP: If you see a yellow attention icon, you may still be able to perform the upgrade (for example, when leveling is occurring). If any unusual icons are visible, check with your HP-authorized service representative - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 14
, to view specific support details, select the connectivity stream document for the switch model/series you are using. • Download the required HBA drivers, firmware and MPIO drivers. NOTE: Additionally, see the "P6000/EVA storage system rules" chapter in the HP SAN Design Reference Guide for general - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 15
to the array being upgraded and optionally the IP addresses of hosts. You must have SNMP access to the switches to collect information from them. The following procedure describes the steps for using SAN Visibility. For complete information about using this tool, see the SAN Visibility online - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 16
the IP address of the primary switch for the SAN for which you want a report. Information will perform data collection for a single switch. Checking this check box discovers and performs Click Discover Switch. This confirms the availability and accessibility of the switch. f. Click Add to add the - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 17
the SMTP address of your mail server. Select the SMTP address from the list. Use this method if you have external e-mail access from your environment. • Manually-Requires that you send your raw data manually to HP. The file will be in .hp format. Checking and upgrading your SAN infrastructure 17 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 18
performance data, it will take at least 10 additional minutes to collect the data. When data collection is complete, the raw data is sent to HP. (You can view the collected files that are sent to HP . If SAN Visibility does not find the SMTP server or if you want to create a report manually, follow - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 19
Manually attach the raw report created with the subject line: "HP Essentials SAN Visibility Report Request". Send the report to the email address: SAN_Visibility@hp on which SAN Visibility is installed. A sample report is shown in Figure 5 (page 19). Figure 5 Sample SAN Visibility report Reading - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 20
window opens (Figure 5 (page 19)). This report will identify the firmware and/or driver version that is currently running on your switches (including the HSV300-S embedded switch controller) and HBAs. 5. To review update recommendations for your switches and HBAs, select the applicable folder on the - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 21
connectivity to the array. An HP P6000 Command View discover operation may be required to re-establish communication with the array. XCS 11200000 upgrade considerations Before upgrading to XCS 11200000, consider the following: • Check that the Device Addition Policy is set to manual. If it is - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 22
the controller software upgrade is complete (including upgrading the firmware on the disk enclosure I/O modules), it may take up to 20 minutes to stabilize device port operations. (The I/O module firmware upgrades are performed sequentially to ensure that host I/O continues during the upgrade.) HP - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 23
the Disk Enclosure Properties page (in HP P6000 Command View) appear blank, specifically, Hardware type, Hardware revision, and Assembly serial number. These blank fields do not affect I/O module operation and do not mean that the upgrade was unsuccessful. HP recommends that you wait 20 minutes to - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 24
performance" in the HP P6000 Command View User Guide. See Table 1 (page 6) for the link to this document. IMPORTANT: If you have an array-based management system, you can install and run HP P6000 Performance Data Collector on a supported Windows host connected to the EVAx400, P63x0 EVA or P65x0 EVA - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 25
following configurations and performance levels have been validated by HP for online upgrade of controller software and disk drive firmware. All configurations include the use of HP P6000 Continuous Access. Table 4 Configurations upgraded from XCS 1000x000 and validated by HP Array Number of disks - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 26
to a host to be seen by HP P6000 Performance Data Collector. However, replication volumes on the replication system are visible without being presented. Because the array controllers are active/active, one controller is preferred (the owning controller) but requests can still be processed by - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 27
Table 5 HP P6000 Performance Data Collector virtual disk statistics (continued) Counter Description Read Miss Req/s The number of read requests per second that failed to complete from the array cache memory and were completed from physical disks instead. Read Miss MB/s The rate at which data - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 28
periods are sufficient for an online controller software upgrade. Native Linux Device-Mapper Multipath If you are using Native Linux Device-Mapper Multipath, see the Native Linux Device-Mapper Multipath for HP StorageWorks Disk Arrays reference guide for additional configuration details. The - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 29
/hp/ MPIO is installed and both paths are active and have access to the array. • Array boot devices are supported with online controller software upgrades, but the page-file disk must not be on the array being upgraded during an online upgrade. See your Windows documentation for instructions - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 30
set for these systems. Using HP P6000 Command View on a Windows 2008 guest system on ESX 4.1 or 5 When using HP P6000 Command View installed on a Windows guest system of ESX 4.1 or 5.0, use one of the following methods to upgrade the firmware to ensure a successful upgrade, or your array code load - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 31
if installed) If the array is in an SVSP configuration with SVSP synchronous mirrors, see the HP SAN Virtualization Services Platform Best Practices Guide for more information before upgrading. This document is available at http://www.hp.com/support/manuals. Select Storage Software under storage and - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 32
- HP P6000 Command View is installed on a management server connected to the array, providing management of multiple HP EVAs. All components of the software suite (HP P6000 Command View, HP P6000 Performance Data Collector, HP Storage System Scripting Utility, HP P6000 Performance Advisor, SMI-S EVA - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 33
verify that the software was installed successfully: 1. Ensure that the software icons for HP P6000 Command View , HP P6000 Performance Data Collector , and/or HP System Scripting Utility appear on the desktop. 2. Run HP P6000 Command View. 3. Verify the display of array resources in the interface - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 34
of HP P6000 Command View. Thus, when you upgrade HP P6000 Command View on the management module, you are also upgrading the management module software. Even if you are not using array-based management, you must complete the procedure in this section for the EVA4400, P63x0 EVA, or P65x0 EVA, to - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 35
Virtual Array Compatibility Reference. See "Reference documentation" (page 6) for the link to this document. NOTE: If you need to update the browser on remote computers, do so after you have upgraded HP P6000 Command View. HP Insight Remote Support software HP strongly recommends that you install HP - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 36
• HP Insight Remote Support Advanced: This software provides comprehensive remote monitoring and proactive service support for nearly all HP servers, storage, network, and SAN environments, plus selected non-HP servers that have a support obligation with HP. It is integrated with HP Systems Insight - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 37
be stable for 48 hours before the upgrade. Check the status of the array to ensure that it is stable, and continue monitoring status until the upgrade begins. 1. Open HP P6000 Command View and click the icon of the array you want to upgrade. 2. Examine the controller event log and check for any - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 38
you upgrade the controller software, you must upgrade HP P6000 Command View (and layered applications) to the required version on both the source and destination sites. • Before you upgrade an array in an HP P6000 Continuous Access environment, ensure that all arrays in the storage network are - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 39
. Continue with Step 2. 2. Restart Controller A: NOTE: HP P6000 Command View identifies the controllers as A and B for EVA 6400/8400 (1 and 2 in case of EVA 4400 and P6xx0 arrays). a. In the navigation pane, select the storage system that is being upgraded. b. Select System Options. c. Under Service - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 40
on the array. HP Storage System Scripting Utility (called the utility) is used to collect configuration data. You can perform this procedure from the management server where HP P6000 Command View is installed, or from any host running the utility to communicate with HP P6000 Command View. NOTE: You - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 41
problems when performing the XCS upgrade procedure, see "Troubleshooting" (page 62) for assistance. If you are still unable to resolve the problem, contact your HP-authorized service representative. IMPORTANT: For upgrade paths, see Tables 3.1.2 and 3.1.3 in the HP P6000 Enterprise Virtual Array - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 42
service representative for assistance. 3. Resolve any hardware component issues that have failed. NOTE: If you need to replace a component, see the replacement instructions for that component or the user guide for your array model. See Table 1 (page 6) for links to these documents. 42 Upgrading - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 43
to resolve the error, contact your HP-authorized service representative for assistance. 4. Using HP P6000 Command View, examine the controller event log and check for any critical events. a. In the navigation pane, click the icon of the array you want to upgrade in the navigation pane. b. Click - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 44
the upgrade, enable UISM in HP P6000 Command View. This will be used by HP Insight Remote Support to indicate the array is in service mode. 1. Open HP P6000 Command View and select the array for which you want to enable UISM. 2. Select System options. 3. Select Configure User-Initiated Service Mode - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 45
least 30 minutes before starting the controller software upgrade. • Before upgrading the controller software, ensure that the array configuration is stable and is not being modified. If configuration changes are in progress, monitor them using HP P6000 Command View and wait until they are complete - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 46
that recommends you to read the texts carefully. Check the box "I have completed the storage system and SAN checks outlined in the HP StorageWorks Enterprise Virtual Array Updating Product Software Guide for my storage system version." and click Next Step (which is disabled if the box is not checked - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 47
readiness checks. The Performing storage system checks window opens. The Code Load Storage System - Page 3 window opens, confirming verification. 11. Click Next step to proceed with the upgrade. The Code Load Storage System - Page 4 window opens. Step 5. Upgrading the controller software 47 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 48
Load Storage System - Page 4 window 12. Click Browse to navigate to the controller software image file (created from the downloaded ISO image) (see "Required kits" (page 7)) and select the appropriate file (Table 10 (page 48)). Table 10 Controller software For this array: P6000 EVA4400 EVA6400 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 49
Figure 19 Code Load Storage System - Page 5 window The new controller software is copied to the controllers and validated (Figure 20 (page 49)). Figure 20 Code load processing page The upgrade process begins and the Initiating firmware code load page opens (Figure 21 (page 50)). This page is - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 50
re-established between HP P6000 Command View and the array. When the array is available, the array appears as available in the navigation pane. Continue with Step 15 to verify that the upgrade completed successfully. After Figure 21 (page 50) appears, the controllers resynchronize and begin running - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 51
(all uppercase) and click Continue. 15. Select the array in the navigation pane and the Initialized Storage System Properties window appears (Figure 25 (page 52)). Verify the that the version of the controller software in the Attributes box is 11200000. Step 5. Upgrading the controller software 51 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 52
after upgrading IMPORTANT: After upgrading the controller software, consider the following: • If the array is initialized after the upgrade, the default data replication protocol will be HP SCSI FC Compliant Data Replication Protocol, which is not currently supported in HP P6000 Continuous Access - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 53
reset the I/O modules to clear the blank fields after the I/O module firmware upgrade has completed successfully. Note that blank fields do not affect the array's ability to process host I/O. See "Resetting the I/O module" (page 54) for more information. Step 5. Upgrading the controller software 53 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 54
instructions in "Resetting the I/O module" (page 54). After completing this second reset, repeat Step 16. If the same problems are detected, contact your HP-authorized service representative for assistance. If no further problems are detected, continue with "Step 6. Upgrading the disk drive firmware - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 55
CV - ServerName. On the content pane, click Discover Storage Systems to allow HP P6000 Command View to discover the array. d. Verify the status of each host before enabling access. Step 6. Upgrading the disk drive firmware Estimated time to complete: Varies depending on the number of disk drives - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 56
. 4. Open and log in to HP P6000 Command View. 5. In the navigation pane, select the array whose disk drive firmware you want to update. The Initialized Storage System Properties window opens. 6. Select the System Options tab. The System Options window opens. 56 Upgrading the Enterprise Virtual - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 57
(page 57). Figure 29 Confirm Disk Drive Code Load Warning Click Continue to proceed or Cancel to exit the procedure. The Code Load Disk Drive Online - Page 1window opens (Figure 30 (page 58)). In Step 1, Click Browse to select the bundled image zip file. Step 6. Upgrading the disk drive firmware 57 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 58
Disk Drives Online - Page 2 window. Figure 31 Code Load Disk Drives On Line - Page 2 window 10. Click Next step. The disk drive firmware upgrade begins. A status page opens, indicating the progress of the upgrade for each disk drive (Figure 32 (page 59)). 58 Upgrading the Enterprise Virtual Array - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 59
. Depending on the I/O load on the array, it can take from 30 seconds to 3.5 minutes per drive to upgrade the firmware. The status is updated at 45-second intervals. CAUTION: Do not select an array to manage it during the disk drive upgrade. If you select an array in the navigation pane to manage it - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 60
(other Vraid virtual disks can continue to service host I/O). TIP: Earlier versions of HP P6000 Command View required you to either delete the Vraid0 virtual disks or ungroup the disks individually before upgrading disk drive firmware. Step 7. Entering array passwords Estimated time to complete - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 61
on your configuration. After the controller software and disk drive firmware have been upgraded successfully, return the array to normal operation: 1. Using HP P6000 Command View, check the overall status of the array to ensure that there are no problems. For instructions, see "Step 1. Checking the - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 62
4 Troubleshooting This chapter provides information to help you solve problems you may encounter with different parts of your array after completing your upgrade. HP P6000 Command View This section describes issues that can impact HP P6000 Command View and its ability to communicate with the array. - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 63
unavailable when a browser makes a request to HP Command View are up. P6000 Command View. In this case, the browser will time out internally. Unknown storage system Symptom HP P6000 Command View reports an unknown storage system error for an array that should be displayed. HP P6000 Command View 63 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 64
, you can perform a Rediscover operation to initiate new commands to the controller. Unknown storage system- cause 2 HP P6000 Command View can only manage controllers that are running supported XCS versions. Corrective action Ensure that you are running the HP P6000 Command View version that is - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 65
be visible to HP P6000 Command View because the controllers are waiting for you to enter the World Wide ID (WWID). This condition occurs if the arraywas uninitialized and the rack is power cycled. Enter the WWID of your system. This can also occur if back-end problems are preventing access to the - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 66
(see "Analyzing array I/O using HP P6000 Performance Data Collector" (page 24)) for the online disk drive firmware upgrade, and restart the upgrade. Drive code load - Unable to determine the condition of the Check the drive properties in HP P6000 Command View volume for problems. Resolve the - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 67
page 67)). Click OK to return to the Initialized Storage System Properties window. Figure 36 Invalid firmware image file (Status code 21006) Bad image header (Status code 65) HP P6000 Command View transfers the XCS controller software to the controller in segments. As each segment is received, it is - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 68
image header (Status code 65) Offline array The controller software upgrade should take approximately 10 minutes to complete. If the array does not come back online within 10 minutes, check the following: • Determine if the problem is with HP P6000 Command View by answering the basic questions at - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 69
a disk group hardware problem • Bad Block Replacement (BBR) performed on a disk Every effort should be made to ensure that these events do not occur during the upgrade process. If controller termination occurs due to multiple resynchronizations, contact your HP-authorized service representative for - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 70
in this guide, see the Manuals page on the Business Support Center website: http://www.hp.com/support/manuals In the Storage section, click Disk Storage Systems or Storage Software, and then select your product. Websites • HP: http://www.hp.com • HP Storage: http://www.hp.com/go/storage • HP Partner - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 71
, and check boxes Text emphasis • File and directory names • System output • Code • Commands, their arguments, and argument values • Code variables • Command variables Emphasized monospace text Indication that the example continues. An alert that calls attention to important information that if not - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 72
VMware, 30 Xen Citrix, 31 HP Command View installing, 32 HP P6000 Command View checking hardware, 12, 41 disabling passwords, 44 online help, 12 web server interaction, 63 HP P6000 Performance Data Collector, 24 HP Passport, 7 HP Support Center, 7 HP technical support, 70 I I/O module resetting, 54 - HP P6300 | HP P6000 EVA Updating Product Software Guide (XCS 11200000) (5697-248 - Page 73
with HP P6000 Command View, 63 O OCP, 34 adding passwords, 60 clearing passwords, 44 offline upgrade, 5 online upgrade, 5 configuration evaluation, 21 considerations, 21 managing host I/O timeouts, 27 selecting when to do, 23 success factors, 21 P P6000 Control Panel, 34 P9000 XP array, 31
HP Enterprise Virtual Array Updating Product
Software Guide (XCS 11200000)
Abstract
This guide describes how to upgrade controller software, disk drive firmware, and related EVA management software on HP
EVA4400/6400/8400s and HP P63x0/P65x0 EVAs. General references to HP P6000 Command View can also refer to
earlier versions of HP Command View EVA.
This guide is intended for field personnel and customers who are experienced with these array models, storage area networks,
HP P6000 Command View and associated software. This guide does not provide information about upgrading or replacing
array hardware.
The information in this guide is subject to change. Please check for the latest version before starting an upgrade.
HP Part Number: 5697-2483
Published: September 2013
Edition: 1