HP Photosmart eStation All-in-One Printer - C510 User Guide - Page 62

Bending the tab out, Closing the printhead latch

Get HP Photosmart eStation All-in-One Printer - C510 PDF manuals and user guides View all HP Photosmart eStation All-in-One Printer - C510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Chapter 1 e. Repeat steps c and d for each of the remaining cartridges. f. Run a finger along the top of the ink cartridges to locate any cartridges that are not snapped completely down. g. If any cartridge was sticking up and does not snap back down into place, the cartridge tab might need to be readjusted. Solution two: Readjust the cartridge tab ▲ Remove the ink cartridge from the carriage. Readjust the cartridge tab a. Gently bend the tab away from the ink cartridge. Be careful not to bend the tab out more than about 1.27 cm (0.5 inches). Figure 1-20 Bending the tab out b. Reinstall the ink cartridge. It should now snap down into place. c. Close the access door, and check if the error message has gone away. d. If you still receive the error message, turn the product off, and then on again. Solution three: Make sure the printhead latch is closed ▲ Make sure the printhead latch is closed ▲ Make sure that the latch securing the printhead is securely closed. Leaving the latch handle raised can result in incorrectly seated ink cartridges and problems printing. The latch must remain down in order to correctly install the ink cartridges. Figure 1-21 Closing the printhead latch 60 Online Topics

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
e
.
Repeat steps c and d for each of the remaining cartridges.
f
.
Run a finger along the top of the ink cartridges to locate any cartridges that are
not snapped completely down.
g
.
If any cartridge was sticking up and does not snap back down into place, the
cartridge tab might need to be readjusted.
Solution two: Readjust the cartridge tab
▲
Remove the ink cartridge from the carriage.
Readjust the cartridge tab
a
.
Gently bend the tab away from the ink cartridge. Be careful not to bend the tab
out more than about 1.27 cm (0.5 inches).
Figure 1-20 Bending the tab out
b
.
Reinstall the ink cartridge. It should now snap down into place.
c
.
Close the access door, and check if the error message has gone away.
d
.
If you still receive the error message, turn the product off, and then on again.
Solution three: Make sure the printhead latch is closed
▲
Make sure the printhead latch is closed
▲
Make sure that the latch securing the printhead is securely closed. Leaving the
latch handle raised can result in incorrectly seated ink cartridges and problems
printing. The latch must remain down in order to correctly install the ink
cartridges.
Figure 1-21 Closing the printhead latch
Chapter 1
60
Online Topics