HP ProLiant 2500 Compaq ProLiant 2500 Family of Servers Maintenance and Servic - Page 27

Hot-Pluggable Hard Drives, Important Guidelines For Replacing

Page 27 highlights

2-14 Removal and Replacement Procedures Hot-Pluggable Hard Drives Hot-pluggable hard drives used in combination with the integrated Wide-Ultra SCSI Controller can be replaced while the power is on. NOTE: It is not necessary to set the SCSI ID jumpers on a Compaq replacement hot-pluggable hard drive. The SCSI ID is set automatically by the backplane board and the hotpluggable tray (to a SCSI ID matching the bay number) when the drive is installed. CAUTION: Before removing any hot-pluggable hard drive, read the guidelines listed in the following section. Important Guidelines For Replacing Hot-Pluggable Hard Drives When you replace a drive configured for fault tolerance, the replacement drive will automatically begin to be restored. When a drive is being restored, the Online LED will flash green. The LED will continue to flash until the drive is completely restored. MSG029.EPS Online Drive Access Drive Failure Figure 2-12.Hot-Pluggable Hard Drive LED Indicators

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140

.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-14
Removal and Replacement Procedures
Hot-Pluggable Hard Drives
Hot-pluggable hard drives used in combination with the integrated Wide-Ultra SCSI
Controller can be replaced while the power is on.
NOTE:
It is not necessary to set the SCSI ID jumpers on a
Compaq replacement hot-pluggable hard drive.
The SCSI
ID is set automatically by the backplane board and the hot-
pluggable tray (to a SCSI ID matching the bay number)
when the drive is installed.
CAUTION:
Before removing any hot-pluggable hard drive,
read the guidelines listed in the following section.
Important Guidelines For Replacing
Hot-Pluggable Hard Drives
When you replace a drive configured for fault tolerance, the replacement drive will
automatically begin to be restored.
When a drive is being restored, the
Online
LED will
flash green.
The LED will continue to flash until the drive is completely restored.
Online
Drive Access
Drive Failure
MSG029.EPS
Figure 2-12.
Hot-Pluggable Hard Drive LED Indicators