HP ProLiant 2500 Compaq ProLiant 2500 Family of Servers Maintenance and Servic - Page 30

Replacing Non-Hot-Pluggable Hard Drives, MSG018.EPS

Get HP ProLiant 2500 PDF manuals and user guides View all HP ProLiant 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

2-17 To Install a Drive 1. Slide the hot-pluggable hard drive all the way into the drive cage. 2. Swing the ejector levers in to seat the drive tray into the backplane connector. Replacing Non-Hot-Pluggable Hard Drives MSG018.EPS Figure 2-15. Removing a Non-Hot-Pluggable Hard Drive 1. Remove the large access panel. 2. Disconnect the power and signal cables from the rear of the hard drive. 3. Squeeze the two release tabs on each side of the drive and slide the drive out. Reverse steps 1 to 3 to replace a non-hot-pluggable hard drive. IMPORTANT: Ensure that the SCSI ID setting on the replaced nonhot-pluggable drive matches the SCSI ID setting on the removed drive. Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
2-17
Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide
To Install a Drive
1.
Slide the hot-pluggable hard drive all the way into the drive cage.
2.
Swing the ejector levers in to seat the drive tray into the backplane connector.
Replacing Non-Hot-Pluggable Hard Drives
MSG018.EPS
Figure 2-15.
Removing a Non-Hot-Pluggable Hard Drive
1.
Remove the large access panel.
2.
Disconnect the power and signal cables from the rear of the hard drive.
3.
Squeeze the two release tabs on each side of the drive and slide the drive out.
Reverse steps 1 to 3 to replace a non-hot-pluggable hard drive.
IMPORTANT:
Ensure that the SCSI ID setting on the replaced non-
hot-pluggable drive matches the SCSI ID setting on the removed
drive.