HP ProLiant 2500 Compaq ProLiant 2500 Family of Servers Maintenance and Servic - Page 71

Match the Array, Replace the Array

Get HP ProLiant 2500 PDF manuals and user guides View all HP ProLiant 2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

3-19 POST Error Messages Continued Error Code Beeps Probable Source of Problem 1794-Drive Array - None This is a warning that Array Accelerator the battery charge is Battery Charge below 75%. Posted Low. writes are disabled. Array Accelerator is temporarily disabled. Array Accelerator will be re-enabled when battery reaches full charge. 1795-Drive Array - None This indicates that while Array Accelerator the system was in use, Configuration Error. power was interrupted Data does not while data was in the correspond to this Array Accelerator drive array. Array memory. Accelerator is The data stored in the temporarily Array Accelerator does disabled. not correspond to this drive array. 1796-Drive Array - None Array Accelerator is Array Accelerator defective or has been Not Responding. removed. Array Accelerator is temporarily disabled. 1797-Drive Array Array Accelerator Read Error Occurred. Data in Array Accelerator has been lost. Array Accelerator is disabled. None Hard parity error while reading data from posted writes memory. Action Replace the Array Accelerator board if batteries do not recharge within 36 power-on hours. 1. Match the Array Accelerator to the correct drive array. -Or2. Run the System Configuration Utility to clear the data in the Array Accelerator. 1. Check that the Array Accelerator is properly seated. 2. Run the System Configuration Utility to re-configure the array controller without the Array Accelerator. Enable Array Accelerator. Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
3-19
Compaq ProLiant 2500 Family of Servers Maintenance and Service Guide
POST Error Messages
Continued
Error Code
Beeps
Probable Source of
Problem
Action
1794-Drive Array -
Array Accelerator
Battery Charge
Low.
Array Accelerator
is temporarily
disabled.
Array Accelerator
will be re-enabled
when battery
reaches full
charge.
None
This is a warning that
the battery charge is
below 75%. Posted
writes are disabled.
Replace the Array
Accelerator board if
batteries do not
recharge within 36
power-on hours.
1795-Drive Array -
Array Accelerator
Configuration Error.
Data does not
correspond to this
drive array. Array
Accelerator is
temporarily
disabled.
None
This indicates that while
the system was in use,
power was interrupted
while data was in the
Array Accelerator
memory.
The data stored in the
Array Accelerator does
not correspond to this
drive array.
1.
Match the Array
Accelerator to the
correct drive array.
-Or-
2.
Run the System
Configuration Utility
to clear the data in
the Array
Accelerator.
1796-Drive Array -
Array Accelerator
Not Responding.
Array Accelerator
is temporarily
disabled.
None
Array Accelerator is
defective or has been
removed.
1.
Check that the
Array Accelerator is
properly seated.
2.
Run the System
Configuration Utility
to re-configure the
array controller
without the Array
Accelerator.
1797-Drive Array -
Array Accelerator
Read Error
Occurred.
Data in Array
Accelerator has
been lost.
Array Accelerator
is disabled.
None
Hard parity error while
reading data from
posted writes memory.
Enable Array
Accelerator.