HP R12000XR HP UPS R5000 Installation Instructions
HP R12000XR Manual
 |
View all HP R12000XR manuals
Add to My Manuals
Save this manual to your list of manuals |
HP R12000XR manual content summary:
- HP R12000XR | HP UPS R5000 Installation Instructions - Page 1
HP UPS R5000 Installation Instructions Part Number 637911-001 - HP R12000XR | HP UPS R5000 Installation Instructions - Page 2
see the HP UPS R5000 User Guide on the HP website (http://www.hp.com/support/UPSR5000_Manuals). Precautions Save these instructions. This document contains important safety instructions that should be followed during installation, operation, and maintenance of the UPS and batteries. WARNING: A risk - HP R12000XR | HP UPS R5000 Installation Instructions - Page 3
specifications" in the user guide. Readying the equipment 1. Check the battery recharge date specified on battery recharge date label has passed without the battery being recharged, contact an HP authorized service representative for directions. 2. Transport the packaged unit to its installation - HP R12000XR | HP UPS R5000 Installation Instructions - Page 4
through the mounting rail into the clip nuts. 2. Insert screws through the rack into the mounting rail and the front of each mounting bracket. 5. Install the rail reinforcement plates and tighten using hex nuts with captive washers included in the kit, instead of the nuts included with the rail - HP R12000XR | HP UPS R5000 Installation Instructions - Page 5
port to the host computer. IMPORTANT: Power protector software requires the communications port to be appropriately cabled to the host computer. NOTE: This port is only used for firmware upgrades. For additional information, see the HP UPS R5000 User Guide. 4. With one person on each side, lift the - HP R12000XR | HP UPS R5000 Installation Instructions - Page 6
procedure was tested on the Windows® XP Professional, Windows Server® 2003, and Windows® Vista Enterprise operating systems using the HP USB to serial converter (part number 304098-001). Depending on your system configuration, a driver download might be required to successfully install the converter - HP R12000XR | HP UPS R5000 Installation Instructions - Page 7
: This port is only used for firmware upgrades. For additional information, see the HP UPS R5000 User Guide. • Use tie wraps and tie wrap requirements stated in NEC (NFPA 70) Articles 645-10 and 645-11, a UPS installed in a computer equipment room must be connected to a REPO circuit. IMPORTANT: The - HP R12000XR | HP UPS R5000 Installation Instructions - Page 8
part of load segment 1 and can be turned off and on using power management software that is installed near user guide batteries With the UPS in Standby mode, allow the batteries to charge before putting the UPS into service. IMPORTANT: Charge the batteries HP Infrastructure Management Pack software - HP R12000XR | HP UPS R5000 Installation Instructions - Page 9
xxx.xxx.xxx.xxx -or- https://xxx.xxx.xxx.xxx where xxx.xxx.xxx.xxx is the static IP address of the UPS Network Module. The log in screen appears. 3. Enter the user name in the User Name field. The default user name is admin. 4. Enter the password in the Password field. The default password is admin. - HP R12000XR | HP UPS R5000 Installation Instructions - Page 10
web interface appears. Configuring the UPS Network Module settings Use the Settings screens of the HP UPS Network Module web interface to configure the UPS Network Module. For more information, see the HP UPS Network Module User Guide on the HP website (http://www.hp.com/support/HPNM_Manuals). - HP R12000XR | HP UPS R5000 Installation Instructions - Page 11
products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein. Microsoft®, Windows®, and Windows Server® are U.S. registered trademarks of Microsoft Corporation. Part Number
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
 |
 |
HP UPS R5000
Installation Instructions
Part Number 637911-001