HP S10614 HP Ground Bonding Rack Option Kit Installation Guide
HP S10614 Manual
View all HP S10614 manuals
Add to My Manuals
Save this manual to your list of manuals |
HP S10614 manual content summary:
- HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 1
HP Ground Bonding Rack Option Kit Installation Guide August 2006 (Second Edition) Part Number 391313-002 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 2
to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 3
Kit In this section About this device...3 Installing the ground bonding rack option kit on HP 10000 G2 Series Racks 4 Installing the ground bonding rack option kit on HP 10000 Series Racks 13 About this device The HP Ground Bonding Rack Option Kit can be used to reduce the level of electromagnetic - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 4
may become unstable if more than one component is extended for any reason. Installing the ground bonding rack option kit on HP 10000 G2 Series Racks Attach the appropriate grounding straps to the following locations: From the system chassis to the front door (without a grounding lug): 1. Remove the - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 5
the second hole below the upper front door hinge on the vertical frame member of the rack. Tighten the screw. 3. Replace the rack front door. 4. Insert a T-25 Torx screw through the other end of the strap, and secure it to the system chassis rail. Installing the HP Ground Bonding Rack Option Kit 5 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 6
left rear door and tighten. 3. Place the other end of the same grounding strap over the grounding lug on the cable access panel. Installing the HP Ground Bonding Rack Option Kit 6 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 7
. From the system chassis rail to the rack top: 1. Insert a T-25 Torx screw rack top. 3. Place an M8 internal serrated on the rack top and tighten. From the grounding lug on the rack top to rack top. 2. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the rack - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 8
slot. 4. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the egress slot and tighten. Installing the HP Ground Bonding Rack Option Kit 8 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 9
the rail) M8 hex nut M8 Belleville toothed washer Facility ground (not included with this kit) M8 x 20 bolt Installing the ground bonding rack option kit on HP 10000 G2 Series Rack side panels From the middle system chassis rail to the bottom side panel: 1. Connect a 36.83-cm (14.5-in) and a 15.24 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 10
system chassis rail. 3. Place the end of the 15.24-cm (6-in) grounding strap over the grounding lug on the top side panel. Installing the HP Ground Bonding Rack Option Kit 10 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 11
top side panel and tighten. 5. Repeat steps 1 through 4 for the other top side panel. Installing the ground bonding rack option kit on HP 10000 G2 Series Rack fan kits From the grounding lug on the rack top to the grounding lug on the fan kit: 1. Place one end of a 15.24-cm (6-in) grounding strap - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 12
internal serrated lock washer and an M8 hex nut over the grounding lug on the egress slot and tighten. Installing the ground bonding rack option kit on HP 10000 G2 Series Rack extension kits 1. Insert a T-25 Torx screw through one end of a 15.24-cm (6-in) grounding strap, and secure it to the rear - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 13
Installing the ground bonding rack option kit on HP 10000 Series Racks Attach the appropriate grounding straps to the following locations: From the system chassis rail to the the same grounding strap over the grounding lug on the right rear door. Installing the HP Ground Bonding Rack Option Kit 13 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 14
left rear door and tighten. 3. Place the other end of the same grounding strap over the grounding lug on the cable access panel. Installing the HP Ground Bonding Rack Option Kit 14 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 15
. From the system chassis rail to the rack top: 1. Insert a T-25 Torx screw rack top. 3. Place an M8 internal serrated on the rack top and tighten. From the grounding lug on the rack top to rack top. 2. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the rack - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 16
slot. 4. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the egress slot and tighten. Installing the HP Ground Bonding Rack Option Kit 16 - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 17
the rail) M8 hex nut M8 Belleville toothed washer Facility ground (not included with this kit) M8 x 20 bolt Installing the ground bonding rack option kit on HP 10000 Series Rack side panels From the system chassis rail to the side panel: 1. Connect a 36.83-cm (14.5-in) and a 15.24-cm (6-in - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 18
side panel. Installing the ground bonding rack option kit on HP 10000 Series Rack fan kits From the grounding lug on the rack top to the grounding lug on the fan kit: 1. Place one end of a 15.24-cm (6-in) grounding strap over the grounding lug on the rack top. 2. Place an M8 internal serrated - HP S10614 | HP Ground Bonding Rack Option Kit Installation Guide - Page 19
3. Place the other end of the same grounding strap over the grounding lug on the egress slot. 4. Place an M8 internal serrated lock washer and an M8 hex nut over the grounding lug on the egress slot and tighten. Installing the HP Ground Bonding Rack Option Kit 19
HP Ground Bonding Rack Option Kit
Installation Guide
August 2006 (Second Edition)
Part Number 391313-002