HP SN3000B HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc
HP SN3000B Manual
View all HP SN3000B manuals
Add to My Manuals
Save this manual to your list of manuals |
HP SN3000B manual content summary:
- HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 1
series 16Gb Switches Hardware Reference Guide Abstract This document provides information on installing, configuring, and maintaining the HP SN6000B Fibre Channel Switch and the HP SN3000B Fibre Channel Switch. It is intended for system administrators and technicians with knowledge of SANs and HP FC - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 2
-Packard Development Company, L.P. © Copyright 2011, 2012 Brocade Communications Systems, Incorporated Confidential computer software. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial Computer Software, Computer Software Documentation - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 3
...11 HP SN3000B 16Gb FC Switch 12 Overview...12 Platform capabilities...12 Platform components...13 Port side of the switch...13 Nonport side of the switch 14 Software options...14 ISL Trunking...14 Hardware options...15 SFP transceivers...16 2 Installing and configuring HP 16Gb FC Switches 17 - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 4
assembly 39 Determining the status of a power supply and fan assembly 40 Removing a power supply and fan assembly 40 Installing a power supply and fan assembly 42 4 Support and other resources 43 HP technical support...43 Subscription service...43 Documentation feedback...43 Related information - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 5
TS/HS dual language sheet 53 Japanese notices...54 Japanese VCCI-A notice...54 Japanese VCCI-B notice...55 Japanese VCCI marking...55 Japanese power cord statement 55 Korean notices...55 KCC statement...55 Class B equipment...55 Taiwanese notices...55 BSMI Class A notice...55 Taiwan battery - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 6
Grounding methods...66 Glossary...67 Index...69 6 Contents - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 7
POD licensing. Base models of the switch contain 24 ports, and up to two additional 12-port POD licenses can be purchased. The switch provides excellent value as the foundation of a SAN and can grow to meet an organization's SAN needs. The HP SN6000B 16Gb FC Switch can be configured in AG mode - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 8
for initial switch setup and factory default restoration. (The integral LEDs remain unlit at all times.) • A USB port that provides storage for firmware updates, supportsave command output, and storage for configuration uploads and downloads. • Two hot-swappable, redundant power supply and fan - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 9
the HP SN6000B 16Gb FC Switch 1. Power supply/fan assembly #2 3. Power supply and fan assembly #1 5. On/off switch 7. Thumbscrew 2. Airflow label 4. Power supply and fan assembly LED 6. Power plug receptacle (with plug retainer) 8. Handle Software options The following optional software kits and - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 10
Integrated Routing • SN6000B 16Gb 24-48 12-port FC Upgrade LTU NOTE: For the latest information on supported software components, see the product QuickSpecs available from the HP website: http://www.hp.com/go/sn6000b/quickspecs ISL Trunking HP ISL Trunking is optional software that enables creating - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 11
the latest information on supported hardware components, see the product QuickSpecs available from the HP website: http://www.hp.com/go/sn6000b/quickspecs SFP transceivers Table 2 SFP transceiver options Option 8Gb Transceivers 10Gb Transceivers 16Gb Transceivers 16Gb Long Wave Transceivers Part - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 12
HP SN3000B 16Gb FC Switch also offers POD licensing. Base models of the switch contain 12 ports, and an additional 12-port POD license can be purchased. NOTE: The base model of the HP SN3000B 16Gb FC Switch includes a single power supply and fan module assembly. An optional second power supply and - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 13
initial switch setup and factory default restoration. (The integral LEDs remain unlit at all times.) • A USB port that provides storage for firmware updates, supportsave command output, and storage for configuration uploads and downloads. • One power supply and fan assembly in the base model. There - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 14
SAN Switch ISL Trunking LTU • HP SN3000B 16Gb 24/12 Fibre Channel Switch 12-port Upgrade LTU NOTE: For the latest information on supported software components, see the product QuickSpecs available from the HP website: http://www.hp.com/go/sn3000b/quickspecs ISL Trunking ISL Trunking is optional - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 15
Ports 8-15 For more information about ISL Trunking, see the Fabric OS 7.0.x Administrator's Guide for the firmware version you are running. Hardware options Table 3 Optional hardware kits Hardware kit Part number HP OM3 LC-LC Optical Cables 0.5m HP OM3 LC/LC Multi-mode Optical Cable AJ833A 1m - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 16
go/sn3000b/quickspecs SFP transceivers Table 4 SFP transceiver options Option 8 Gb Transceivers 16 Gb Transceivers 16 Gb Long Wave Transceivers Part number AJ716B HP 8Gb Shortwave B-series FC SFP+ AJ717A HP 8Gb LW B-series 10km FC SFP+ AW538A HP B-series 8Gb LW 25km FC SFP QK724A HP B-series 16Gb - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 17
during shipping: • One HP SN6000B 16Gb FC Switch with two integrated power supply/fan assemblies, or one HP SN3000B 16Gb FC Switch with one integrated power supply/fan assembly NOTE: The HP SN3000B 16Gb FC Switch can, as an option, be configured with a second power supply/fan assembly, which must - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 18
provides instructions for installing the HP SN6000B 16Gb FC Switch and the HP SN3000B 16Gb FC Switch. Items required for installation To set up the switch for the first time, you will need the following: • Workstation with an installed terminal emulator (such as HyperTerminal) • Unused IP address - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 19
rack using the Rack Mount Kit Use the SN6000B and the SN3000B Switch Rack Mount Kits to install the switch in an HP 10000 Series Rack. CAUTION: Install the Rack Mount Kits as described in this section so that when the switch is installed, the port side faces the rear of the rack. This configuration - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 20
switch power cords through these holes later in this procedure. 3. Attach each rear mounting bracket to a rear rack upright column using two Phillips screws and adapter washers. See Figure 8 (page 20). Figure 8 Installing the rear mounting brackets 20 Installing and configuring HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 21
to designate the left side and right side of the rack as viewed from the front of the cabinet. Figure Attach the front of the rail to a front rack upright column using two Phillips screws and adapter TIP: Tighten the rear screws just enough for the end of the screw to go through the rear brackets - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 22
SN3000B 24-port switch. See Figure 11 (page 23). IMPORTANT: Make sure that the power cords do not come in contact with any sharp edges. NOTE: If you are configuring the second (optional) power supply, the SN3000B 24-port switch will also have two power cords. 22 Installing and configuring HP 16Gb FC - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 23
end of the power cords to power sources on separate circuits to protect against AC failure. (Make sure that two power cords are connected to the SN6000B 48-port switch and one power cord is connected to the SN3000B 24-port switch.) NOTE: If you are configuring the second (optional) power supply - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 24
. NOTE: If you are configuring the second (optional) power supply on the SN3000B switch, it will also have two power cords. Ensure that the cords have a minimum service loop of 6 inches available and are routed to avoid stress. 5. Power on the power supplies by setting both AC switches to the on - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 25
power LEDs return to a normal state. 2. When the terminal emulator stops reporting information, press Enter to display the login prompt. 3. Log in to the switch as admin, using the default password, password. You are prompted to change the default password at initial login. NOTE: You can configure - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 26
not affect switch operation. However, setting the date and time accurately is important because these values are used for logging, error detection, and troubleshooting. Setting the date 1. Log in to the switch using the default password, password. 26 Installing and configuring HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 27
are interpreted as 2000-2069.) For example: switch:admin> date Fri Sep 30 17:01:48 UTC 2011 switch:admin> date "0929123011" Thu Sep 29 12:30:00 UTC 2011 switch:admin> Setting the time zone Users with administrative permissions can set the time zone for the switch by the zone name (such as PST), by - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 28
server fails. The principal or primary FCS switch synchronizes its time with the NTP server every 64 seconds. Synchronizing local time using NTP To synchronize the local time using NTP: 1. Log in to the switch using the default password, password. 28 Installing and configuring HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 29
the principal or primary FCS switch are propagated to all switches in the fabric. For more information on using an NTP server, and IPv6 considerations, see the Fabric OS Administrator's Guide. Configuring the zones and selecting devices See the Network Advisor User Manual, available from the storage - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 30
SFP+ transceivers in the FC ports on the switch to match the ports displayed in the Device Connection window . If you Figure 14 Inserting an SFP+ transceiver with no pull tab in an FC port Figure 15 Inserting a 16 Gb/s SFP+ transceiver in an FC port 30 Installing and configuring HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 31
the Fabric OS 7.0.x Administrator's Guide and the Fabric OS 7.0.x Command Reference Manual for detailed instructions on setting all supported switch features. Switch status policy Switch status policy is a feature that monitors different switch parameters such as power supplies and fan units, and - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 32
. This command uploads the switch configuration to the server, making it available for downloading to a replacement switch, if necessary. For instructions on backing up the configuration, see the Fabric OS Administrator's Guide. 2. Follow the on-screen prompts. Installing and activating Port Upgrade - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 33
is not available for the switch. See the Access Gateway Administrator's Guide for details on any restrictions. • In Native mode, the SN6000B switch provides up to 48 external FC ports and the SN3000B switch provides up to 24 external FC ports. These universal self-configuring ports are capable of - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 34
the fabric switch configuration. The AG parameters, such as F_Port-to-N_Port mapping, Failover, and Failback are removed automatically. When the switch reboots, it starts in Native mode. For instructions on adding the switch back to the core fabric, see the Access Gateway Administrator's Guide. To - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 35
16Gb FC Switches This chapter discusses switch power, LEDs, maintenance, and management. Powering the switch on and off • Power switches are located on the nonport side of the switch. • If the switch is mounted in a rack, you must remove the plenum to access the power switches. • Power is supplied - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 36
is off or there is an internal power supply failure. Recommended action Verify that the system is powered on (power supply switches set to I), the power cables are attached, and the power source is live. The unit may be faulty. Contact your switch service provider. Steady green System is on and - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 37
configuration of the HP SN3000B 16Gb FC Switch includes a single power supply/fan assembly. Table 6 (page 37) describes the status. Figure 17 Power supply/fan status LEDs 1. Power supply commands, see the Fabric OS 7.0.x Command Reference Manual. POST You can monitor the results of the diagnostic - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 38
tests can temporarily lock the transmit and receive speed of the links. • HP does not support 2Gb connectivity to the SN6000B or the SN3000B switches. For information about specific diagnostic tests, see the Fabric OS Troubleshooting and Diagnostics Guide. 38 Operating HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 39
Fabric OS Administrator's Guide and the Fabric OS 7.0.x Command Reference Manual. Native in-band interface (over HBA only) Network Advisor (option to purchase) See the Network Advisor documentation set. Ethernet or serial connection IP over FC FRU removal and replacement The power supply and fan - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 40
19 (page 41)): 1. If the switch is rack mounted, remove the plenum. 2. If the switch has two power supply and fan assemblies, go to step 3. When replacing the power supply and fan assembly in an HP SN3000B 16Gb FC Switch that has only one assembly, the switch must be powered off before removing the - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 41
to be replaced by setting the AC power switch to the off (O) position. The fans in the other power supply automatically switch to high speed to maintain adequate cooling. 4. Unplug the power cord from the power supply and fan assembly being replaced. 5. Unscrew the captive screw using a Phillips - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 42
seated properly. 7. If the switch is installed in a rack, replace the plenum. 8. Optional: If you are using the CLI, enter the psshow command at the command-line prompt to display the status. Power supply and fan assembly status can also be viewed using Web Tools. 42 Operating HP 16Gb FC Switches - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 43
of HP. Related information The following documents provide related information. See the appropriate document version for your operating environment. • Network Advisor User Manual • Fabric OS 7.0.x Administrator's Guide • Fabric OS 7.0.x Command Reference Manual • SAN TECH NOTE - Preparing to Install - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 44
/manuals • http://www.hp.com/support/downloads Rack stability Rack stability protects personnel and equipment. WARNING! To reduce the risk of personal injury or damage to equipment: • Extend leveling jacks to the floor. • Ensure that the full weight of the rack rests on the leveling jacks. • Install - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 45
information or specific instructions. NOTE: Provides additional information. TIP: Provides helpful hints and shortcuts. Customer self repair HP CSR programs allow you to repair your HP product. If a CSR part needs replacing, HP ships the part directly to you so that you can install it at your - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 46
. They meet IEC 61000-4-5 surge voltage requirements and support autoranging to accommodate input voltages and line frequencies. Each power supply has built-in fans for cooling. Table 11 HP SN6000B 16Gb FC Switch power supply specifications Specification Input voltage Input frequency Values Range - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 47
12 HP SN3000B 16Gb FC Switch power supply specifications Specification Input voltage Input frequency Inrush current Single power supply output Input line protection System power Heat dissipation 338 BTU/hr (32-port configuration) 375 BTU/hr (48-port configuration) N/A Environmental requirements 47 - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 48
F frames for the 48 port chassis) Table 15 HP SN3000B 16Gb FC Switch general specifications Specification Configurable port types System architecture System processor ANSI FC protocol Modes of operation Fabric initialization FC-IP Aggregate switch I/O bandwidth FC port-to-port latency Aggregate - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 49
The ports operate at 2, 4, 8, or 16 Gb/s, depending on SFP+ models, and are able to autonegotiate to the maximum link speed. NOTE: HP does not support 2 Gb/s connectivity to the HP SN6000B 16Gb FC Switch or the HP SN3000B 16Gb FC Switch. Serial port specifications The serial port is located on the - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 50
supported 8 Not supported Description N/A N/A AG default port mapping Table 19 (page 50) lists the port mappings of F_Ports to N_Ports. Table 19 HP SN6000B 16Gb FC Switch AG default 20 HP SN3000B 16Gb FC Switch AG default port mapping Total ports 24 F_Ports 0-15 N_Ports 16-23 Default port - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 51
may reasonably be expected to be installed in a residential environment (for example, personal computers). The FCC requires devices in both classes to bear a label indicating the interference potential of the device as well as additional operating instructions for the user. FCC rating label The FCC - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 52
or telephone: • Hewlett-Packard Company P.O. Box 692000, Mail Stop 510101 Houston, Texas 77269-2000 • Or call 1-281-514-3333 Modification The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 53
be obtained from http://www.hp.com/go/certificates. Hewlett interference in which case the user may be required to take Brocade provides with respect to its products as set forth in the applicable contract between Brocade and its customer. Brocade accordance with the operating manual of the product. - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 54
Japanese notices Japanese VCCI-A notice 54 Regulatory compliance notices - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 55
notice Japanese VCCI marking Japanese power cord statement Korean notices KCC statement Class A device (Broadcasting Communication Device for Office Use): This device obtained EMC registration for office use (Class A), and may be used in places other than home. Sellers and/or users need to take note - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 56
other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of HP Authorized Service technicians to repair the unit. The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 57
Dutch laser notice French laser notice German laser notice Laser compliance notices 57 - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 58
Italian laser notice Japanese laser notice Spanish laser notice 58 Regulatory compliance notices - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 59
English recycling notice Disposal of waste equipment by users in private household in the European Union This electronic equipment. For more information, please contact your household waste disposal service Bulgarian recycling notice Czech recycling notice Likvidace zařízení v domácnostech - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 60
remettant à une déchetterie effectuant le recyclage des équipements électriques et électroniques. Pour de plus amples informations, prenez contact avec votre service d'élimination des ordures ménagères. German recycling notice Entsorgung von Altgeräten von Benutzern in privaten Haushalten in der EU - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 61
Italian recycling notice Smaltimento di apparecchiature usate da parte di utenti privati nell'Unione Europea Questo simbolo avvisa di non smaltire il prodotto con i normali rifi uti domestici. Rispettare la salute umana e l'ambiente conferendo l'apparecchiatura dismessa a un centro di raccolta - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 62
Romanian recycling notice Casarea echipamentului uzat de către utilizatorii casnici din Uniunea Europeană Acest simbol înseamnă să nu se arunce produsul cu alte deşeuri menajere. În schimb, trebuie să protejaţi sănătatea umană şi mediul predând echipamentul uzat la un punct de colectare desemnat - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 63
Battery replacement notices Dutch battery notice French battery notice Battery replacement notices 63 - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 64
German battery notice Italian battery notice 64 Regulatory compliance notices - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 65
Japanese battery notice Spanish battery notice Battery replacement notices 65 - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 66
. This type of damage can reduce the life expectancy of the device. To prevent electrostatic service tools. • Use a portable field service kit with a folding static-dissipating work mat. If you do not have any of the suggested equipment for proper grounding, have an HP authorized reseller install - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 67
. Fibre Channel. Fibre Channel Physical and Signaling Interface. Fibre Channel over Internet Protocol. Fibre Channel Routing. Fabric Configuration Server. Fibre Connection or Fibre Connectivity. Field replaceable unit. File Transfer Protocol. Greenwich Mean Time. Host Bus Adapter. Inter-Switch Link - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 68
UTC VF WWN Coordinated Universal Time. Virtual Fabric. World Wide Name. 68 Glossary - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 69
configuring the switch, 17 ISL trunking groups HP SN3000B 16Gb FC Switch, 14 HP SN6000B 16Gb FC Switch, 10 J Japanese notices, 54 K Korean notices, 55 L laser compliance notices, 56 licenseadd command, 32 licenseshow command, 32 O optional hardware kits HP SN3000B 16Gb FC Switch, 15 HP SN6000B 16Gb - HP SN3000B | HP B-series 16Gb Switches Hardware Reference Guide (5697-1522, Marc - Page 70
installing and configuring, 17 SN6000B 16Gb FC Switch installing and configuring, 17 status policy, 31 Subscriber's Choice, HP, 43 switch status policy, 31 symbols in text, 45 T Taiwanese notices, 55 technical support HP, 43 service locator website, 44 text symbols, 45 W warning rack stability, 44
HP B-series 16Gb Switches Hardware
Reference Guide
Abstract
This document provides information on installing, configuring, and maintaining the HP SN6000B Fibre Channel Switch and
the HP SN3000B Fibre Channel Switch. It is intended for system administrators and technicians with knowledge of SANs and
HP FC switches.
HP Part Number: 5697-1522
Published: March 2012
Edition: 2